• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.16 no.28
• /
• pp.181-186
• /
• 1993

The objective of this paper is to present a method for synthetic performance and quality evaluation of dial up network modem in users place. In the past, universally recognized criteria have not been available to model switched network modem performance. Reasonable assurance of modem performance on the public switched telephone network by standardized test channel which is suggested by ELA(Electronic Industries Association). These tests of modem from a variety manufacturers more reflective of actual performance on the network.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.1346-1349
• /
• 2002

This paper presents the design and implementation of 16-QAM modem that can be applied to fixed broadband wireless access systenm. It is implemented in the hardware prototype that consist of FPGA(Field Programmable Gate Array) for digital signal processing and analog front end module for analog signal processing. We provide 20.48Mbps data rate using implemented modem and test the modem in KOREA 26㎓ broadband wireless local loop system including IFU(Intermediate Frequency Unit) and RFU(Radio Frequency Unit) via air interface.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.4
• /
• pp.59-64
• /
• 2020

Occasionally, MODEM test in satellite communication systems are needed. But Rx terminals in satellite communications are designed to obtain high SNR generally, therefore artificial bad conditions and environments are demanded for the test. One of the typical method is satellite output power reduction. Using noise generator can be another method. However, these costs a lot of money, time, and procedures in reality. In order to overcome these problems, this paper proposes an artificial noise generation method for MODEM test in satellite communication systems. First of all, SNR of a general heterodyne Rx terminal is calculated. Based on the calculation, a new model which is including variable attenuator is proposed to increase noise level. Simulation results illustrate the variable attenuator can control SNR, and these show that MODEM test in satellite communication systems be possible.

• Journal of IKEEE
• /
• v.18 no.4
• /
• pp.495-501
• /
• 2014

In this paper, we designed a diversity modem hardware architecture for IEEE802.11p WAVE and tested the modem on the road with car attached shark antenna. One of the dual channel modem and the diversity single modem with maximum ratio combining algorithm can be selected on the designed architecture. The designed modem have been implemented on the Xillinx Kintex7 FPGA. We tested the modem performance on the smart highway experience road. As experimental results, we can verify the performance of the diversity modem on real road and the enlarged communication range by more than 30%.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.2
• /
• pp.205-211
• /
• 2008

This paper describes the method aimed at establishing the equipment measuring the parameter of Cable Network by Best proper Cable Modem and PDA through RS232 interface. In this paper, we propose our creative experimental configuration and develope the Cable Modem (DOCSIS 2.0) superior more performing than the referred Cable Modem (DOCSIS 1.0, 1.1) and the measuring equipment of HFC network compositing of Cable Modem and PDA through RS232 interface. This equipment analyzes Upstream (U/S) and Downstream (D/S) Signal quality and generates the signal of Upstream by CW signal. The paper also provides the experimental results to check the Best Proper Cable Modem and the displayed screen for parameters for SNR, BER and the demodulated IQ diagram of 256QAM through LCD of PDA. Henceforth, it'll be possible to support a variety of the functions for E-mail, Internet, the speed test of WEB connection and the transmission of the measured result real time by PDA.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.12 no.6
• /
• pp.612-620
• /
• 1987

In this paper, the optical modem for data link realization is designed with the advantages of optical fiber, large bandwidth, high speed and long haul communication. Modem interface, CCITT V.24 and EIA RS-232C is adopted for the compatibility with existing systems, and biphase coding format is used for digital modulation. And also, modem has serveral loopback test facility in order to diagnose system itself. Optical transmitter and receiver are designed to have the receiving sensitivity of -30dBm at $10^-9$BER in the short wavelength region. Developed system is capable of transmitting data rate at 1200bps up to 57.6Kbps in sync., and at any bps within DC to 200Kbps in async transmission.

• Journal of Communications and Networks
• /
• v.13 no.1
• /
• pp.70-76
• /
• 2011

This paper presents the unified user equipment (UE) baseband modulation and demodulation (modem) hardware platform architecture to support multiple radio access technologies. In particular, this platform selectively supports two systems; one is HEDGE system, which is the combination of third generation partnership project (3GPP) Release 7 high speed packet access evolution (HSPA+) and global system for mobile communication (GSM)/general packet radio service (GPRS)/enhanced data rates for GSM evolution (EDGE), while the other is LEDGE system, which is the combination of 3GPP Release 8 long term evolution (LTE) and GSM/GPRS/EDGE. This is done by applying the flexible pin multiplexing scheme to a hardwired pin mapping process. On the other hand, to provide stable connection, high portability, and high debugging ability, the stacking structure is employed. Here, a layered board architecture grouped by functional classifications is applied instead of the conventional one flatten board. Based on this proposed configuration, we provide a framework for the verification step in wireless cellular communications. Also, modem function/scenario test and inter-operability test with various base station equipments are verified by system requirements and scenarios.

• Journal of IKEEE
• /
• v.19 no.3
• /
• pp.400-406
• /
• 2015

In this paper, we designed a decision feedback based diversity modem hardware architecture for IEEE802.11p WAVE and tested the modem on the road with car attached shark antenna. One of the dual channel modem and the diversity single modem with maximum ratio combining algorithm can be selected on the designed architecture. The designed modem have been implemented on the Xillinx Kintex7 FPGA. We tested the modem performance on the smart highway experience road. As experimental results, we can verify the performance of the diversity modem on real road and the enlarged communication range by more than 100%.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.2
• /
• pp.24-30
• /
• 2009

In this paper, the FPGA modem platform complying with 3GPP Release 7 eHSPA specifications and its regularized verification flow are proposed. The FFGA platform consists of modem board supporting physical layer requirements, MCU and DSP core embedded control board to drive the modem board, and peripheral boards for RF interfacing and various equipment interfaces. On the other hand, the proposed verification flow has been regularized into three categories according to the correlation degrees of hardware-software inter-operation, such as simple function test, scenario test call processing and system-level performance test. When it comes to real implementations, the emulation verification strategy for low power mobile SoC is also introduced.

• Journal of Korea Multimedia Society
• /
• v.8 no.5
• /
• pp.660-669
• /
• 2005

In this paper 10Mbps master-slave based PLC modems are tested for measuring and analyzing both network and application level performances in the general buildings. The devices under test consist of one master PLC modem and three slave modems. The selected parameters for inspecting the performances are throughput, latency and frame loss rate from the RFC 2544, and one-to-many and many-to-one throughput from the RFC 2285. The results of the performance test show that the PLC modems have Performed better in data transmission when the frame size is increased and the transmission speed is decreased. It is expected that these results will be useful to analyze the effect of noise sources when compared to the performance test under the noiseless environments.