• Earthquakes and Structures
• /
• 제26권6호
• /
• pp.449-461
• /
• 2024

The vertical reinforcement connection between the precast reinforced concrete shear wall and the cast-in-place reinforced concrete member is vital to the performance of shear walls under seismic loading. This paper investigated the structural behavior of three precast reinforced concrete shear walls, with different levels of connection (i.e., full connection, partial connection, and no connection), subjected to quasi-static lateral loading. The specimens were subjected to a constant vertical load, resulting in an axial load ratio of 0.4. The crack pattern, failure modes, load-displacement relationships, ductility, and energy dissipation characteristics are presented and discussed. The resultant seismic performances of the three tested specimens were compared in terms of skeleton curve, load-bearing capacity, stiffness, ductility, energy dissipation capacity, and viscous damping. The seismic performance of the partially connected shear wall was found to be comparable to that of the fully connected shear wall, exhibiting 1.7% and 3.5% higher yield and peak load capacities, 9.2% higher deformability, and similar variation in stiffness, energy dissipation capacity and viscous damping at increasing load levels. In comparison, the seismic performance of the non-connected shear wall was inferior, exhibiting 12.8% and 16.4% lower loads at the yield and peak load stages, 3.6% lower deformability, and significantly lower energy dissipation capacity at lower displacement and lower viscous damping.

• Steel and Composite Structures
• /
• 제28권1호
• /
• pp.73-82
• /
• 2018

This paper experimentally and analytically elucidates the shear behavior and shear bearing capacity of partially prefabricated steel reinforced concrete (PPSRC) columns and hollow partially prefabricated steel reinforced concrete (HPSRC) columns. Seven specimens including five PPSRC column specimens and two HPSRC column specimens were tested under static monotonic loading. In the test, the influences of shear span aspect ratio and difference of cast-in-place concrete strength on the shear behavior of PPSRC and HPSRC columns were investigated. Based on the test results, the failure pattern, the load-displacement behavior and the shear capacity were focused and analyzed. The test results demonstrated that all the column specimens failed in shear failure mode with high bearing capacity and good deformability. Smaller shear span aspect ratio and higher strength of inner concrete resulted in higher shear bearing capacity, with more ductile and better deformability. Furthermore, calculation formula for predicting the ultimate shear capacity of the PPSRC and HPSRC columns were proposed on the basis of the experimental results.

• 콘크리트학회논문집
• /
• 제16권5호
• /
• pp.627-634
• /
• 2004

이 연구에서는 벽식 구조 아파트 건물을 대상으로 장변 방향 내력벽 시스템의 내진 성능을 평가하기 위하여 1/3 축소모형시험체를 제작하여 정적반복가력실험을 실시하였으며, 실험결과와 비선형 해석결과로부터 내력벽 시스템의 거동 특성과 내진성능에 대한 평가 결과 및 논의를 다루고 있다 일반적으로 내력벽구조시스템은 초기강성 및 항복강도는 매우 크지만, 변형능력이 부족한 것으로 인식되고 있지만 실험결과에 의하면 지붕층 부재각 $2.0\%$까지 급격한 강도 저하를 보이지 않고 안정된 이력거동을 보여주고 있다. IDARC 5.0을 사용하여 수행한 비선형 해석결과는 시험체의 하중-변위 관계를 양호하게 예측할 수 있는 수준이라고 판단하였다.

• 한국융합학회논문지
• /
• 제11권11호
• /
• pp.239-247
• /
• 2020

본 연구는 풍력발전기용 베어링의 응력저감을 위한 설계와 검증에 관한 것이다. 일반적인 4점 접촉 볼베어링의 구조를 가지고 있는 슬루잉 베어링은 큰 모멘트 하중이 작용하면 접촉점이 레이스웨이 끝단부로 이동하여 국부적인 응력상승 문제가 발생한다. 본 연구에서는 이러한 접점 이동을 줄이기 위한 베어링을 설계하였다. 전통적인 볼베어링과 새로인 설계된 베어링의 극한하중 하에서의 변형거동을 볼을 스프링요소로 치환하여 유한요소해석을 통하여 계산하였다. 볼과 레이스웨이의 접촉응력은 변형거동 해석결과를 경계조건으로 입력하여 유한요소해석으로 계산하였다. 베어링 구조에 따른 접촉부 응력 비교를 통하여 베어링의 응력해석 방법의 효용성을 검증하였다.

• Tribology and Lubricants
• /
• 제40권1호
• /
• pp.17-23
• /
• 2024

This study analyzes the thermal effects on the performance of an air foil thrust bearing (AFTB) using COMSOL Multiphysics to approximate actual bearing behavior under real conditions. An AFTB is a sliding-thrust bearing that uses air as a lubricant to support the axial load. The AFTB consists of top and bump foils and supports the rotating disk through the hydrodynamic pressure generated by the wedge effect from the inclined surface of the top foil and the elastic deformation of the bump foils, similar to a spring. The use of air as a lubricant has some advantages such as low friction loss and less heat generation, enabling air bearings to be widely used in high-speed rotating systems. However, even in AFTB, the effects of energy loss due to viscosity at high speeds, interface frictional heat, and thermal deformation of the foil caused by temperature increase cannot be ignored. Foil deformation derived from the thermal effect influences the minimum decay in film thickness and enhances the film pressure. For these reasons, performance analyses of isothermal AFTBs have shown few discrepancies with real bearing behavior. To account for this phenomenon, a thermal-fluid-structure analysis is conducted to describe the combined mechanics. Results show that the load capacity under the thermal effect is slightly higher than that obtained from isothermal analysis. In addition, the push and pull effects on the top foil and bump foil-free edges can be simulated. The differences between the isothermal and thermal behaviors are discussed.

• Earthquakes and Structures
• /
• 제18권5호
• /
• pp.599-607
• /
• 2020

This paper deals with the experimental investigation on the behavior of RCS beam-column exterior joints. Two full-scale specimens of joints between reinforced concrete columns and steel beams are tested under cyclic loading. The objective of the test is to study the effect of steel fiber reinforced concrete (SFRC) on the seismic behavior of RCS joints. The load bearing capacity, story drift capacity, ductility, energy dissipation, and stiffness degradation of specimens are evaluated. The experimental results point out that the FRC joint is increased 20% of load carrying capacity and 30% of energy dissipation capacity in comparison with the RC joint. Besides, the FRC joint shown lower damage and better ductility than RC joint.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2000년도 학술발표회 발표논문집
• /
• pp.438-443
• /
• 2000

A wide range of problems geotechnical engineering have been analyzed by using the finite element method. In order to establish confidence in a numerical procedure, it is desirable that numerical solution be verified against field or laboratory observations, or both, and in order to aid the user in applying the method to practical problems, it is necessary to examine effects of various parameters that influence the behavior of engineering structures. Often it can be profitable to translate numerical solutions in formats that can be used readily for design analysis. The allowable bearing capacity of concrete piles is mainly governed by settlement rather than by strength of soil. Therefore, the load-displacement behavior of piles should be well understood at the design stage. This paper deals with some of these goals by considering the problem of load-displacement behavior of axially-loaded pile foundations.

• 한국지반공학회논문집
• /
• 제34권11호
• /
• pp.107-119
• /
• 2018

PHC말뚝, 확장판 선단부착 PHC말뚝, 강관 선단부착 PHC말뚝을 현장 시험 부지에서 시험시공하였다. 이들 선단변형 PHC말뚝들에 대하여 하중전이측정이 수반된 연직압축정재하시험을 실시하였으며 시공직후 항타후 동재하시험을 수행하였다. 또한 선단부만 그라우팅한 선단변형PHC말뚝에 대한 연직압축정재하시험도 실시하였다. 3가지 다양한 선단말뚝들 즉, PHC말뚝, 확장판 선단부착 PHC말뚝, 강관 선단부착 PHC말뚝의 하중-침하량 거동은 거의 동일한 양상을 나타내었다. 따라서 말뚝이 선단지지층에 근입된 길이가 동일하고 말뚝 본체의 직경이 동일할 경우 확장판 선단부착 PHC말뚝 및 강관 선단부착 PHC말뚝의 지지력 증대 효과는 거의 없는 것으로 나타났다. 최종재하하중단계에서 PHC말뚝, 확장판 선단부착 PHC말뚝, 강관 선단부착 PHC말뚝의 주면마찰력은 각각 전체 재하하중의 95.8%, 95.6%, 97.8%를 분담하였으며, 선단지지력은 전체 재하하중의 4.2%, 4.4%, 2.2%를 분담하였다.

• 한국가스학회지
• /
• 제20권3호
• /
• pp.73-77
• /
• 2016

본 연구에서는 여러 가지의 절단면 형상을 구비한 중공축이 동등한 최적을 갖는 경우에 대한 변위거동 안전성을 유한요소법으로 해석하였다. FEM 해석결과에 의하면, 외측튜브, 중간튜브, 내측튜브와 이들 튜브 사이를 연결하기 위해 X-타입 또는 Y-타입의 칼럼을 설치하였을 때 중공축 길이의 중간부에서 발생하는 최대 변위량을 줄여주는 것으로 나타났다. 특히, 하중을 지지하기 위해 구비된 X-타입 또는 Y-타입의 칼럼을 위상차 없이 외측튜브와 내측튜브를 중심축을 향해 직접 연결하면 중공축의 변위량을 줄이는 효과가 있는 것으로 나타났다. 그리고 동등한 체적을 갖는 중공축에서 발생하는 수직 변위량을 줄여주고, 변위거동 안전성을 높이기 위해서는 하중을 지지하기 위한 칼럼의 두께를 두껍게 설계하는 것이 바람직함을 알 수 있다.

• 산업기술연구
• /
• 제18권
• /
• pp.7-16
• /
• 1998

This paper is an experimental study of investigating the reinforcing effect and the behavior of cohesionless slope installed with reticulated root pils. Reduced scale model tests with plane strain conditions were performed to study the behavior of the strip footing located on the surface of cohesionless slopes reinforced with root piles. Model tests were carried out with Jumunjin Standard Sand of 45% relative density prepared by raining method to have an uniform slope foundation during tests. Slope of model foundation was 1 : 1.5 and a rigid model slop. Parametric model tests were performed with changing location of model footing, arrangements of root piles and angles of pile installation. On the other hands, the technique with camera shooting was used to monitor sliding surface formed with discontinuty of dyed sand prepared during formation o foudation. From test results, parameters affecting the behavior of model footing were analyzed qualitatively to evaluate their effects on the characteristic of load - settlement, ultimate bearing capacity of model footing and failure mechanism based on the formation of failure surface.