• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.8
• /
• pp.1885-1890
• /
• 2013

In this paper, the electrical properties of nanoscale junctionless p-channel MuGFET at cryogenic temperature have been analyzed experimentally. The experiment was performed using a cryogenic probe station which uses the liquid Helium. It has been observed that the drain current oscillation at low drain voltage and cryogenic temperature was more pronounced in junctionless transistor than in accumulation mode transistor. The reason for more marked oscillation is due to the smaller electrical cross section area of the inversion channel which is formed at the center of silicon film in junctionless transistor. It was also observed that the drain current and maximum transconductance were increased as the measurement temperature increased. This is resulted from the increase of hole mobility and the decrease of the threshold voltage as the measurement temperature increases. The drain current oscillation due to the quantum effects can be occurred up to the room temperature when the device size scales down to the nanometer level.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.1 no.1
• /
• pp.37-42
• /
• 2000

Copper thin films have been prepared by a metal organic chemical vapor deposition (MOCVD) technology on polyimide and TiN substrates. The Cu-MOCVD technology has advantages of the high deposition rate and the good step coverage compared with the conventional physical vapor deposition (PVD) technology in several industrial applications. The Cu films have been deposited with varying the experimental conditions of substrate temperatures and copper source vapor pressures. The films were annealed in a vacuum condition after the deposition, and the annealing effect on the electrical properties of the films was measured. The crystallinity and the microstructures of the films were observed by scanning electron microscopy (SEM), and the electrical resistivity was measured by 4-point probe. In the case of the Cu deposition on TiN substrate, the best electrical property of the films was measured for the samples prepared at 18$0^{\circ}C$. Very high deposition rate of the Cu film up to 250 nm/min was obtained on the polyimide substrate when the mixture of liquid and vapour precursor was used.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.639-642
• /
• 2005

HTS Transformer developing is developing a power distribution and transmission class HTS transformer that is one of the 21st century superconducting frontier projects. Therefore, we prepared the model, that is Z continuous winding from Kapton insulated Cu tape for a small simulated the HTS transformer. For the development of electrical insulation design of a HTS transformer with Z continuous winding, we have been discussed insulation composition and investigated breakdown characteristics such as breakdown of liquid $N_2(LN_2)$, polymer and surface flashover on FRP and breakdown-surface combination in $LN_2$. Also we have been designed and manufactured a bobbin that has spiral slot for the Z continuous winding. The Z continuous winding mini-model from Kapton film insulated Cu tape for simulated 22.9kV class HTS transformer has been constructed using 0.1 % breakdown strength obtained by Weibull distribution. The widing model was measured their insulation characteristics such as ac (50kV, 1min) and impulse (154kV, $1.2\times50{\mu}s$ full wave, 3 times) withstand test and its excellent performance was confirmed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.5 s.248
• /
• pp.413-421
• /
• 2006

The bubble dynamics induced by direct laser heating is experimentally analyzed as a first step to assess the technical feasibility of laser-based ink-jet technology. To understand the interaction between laser light and ink, the absorption spectrum is measured for various ink colors and concentrations. The hydrodynamics of laser-generated bubbles is examined by the laser-flash photography. When an Ar ion laser pulse (wavelength 488 nm) with an output power up to 600 mW is incident on the ink solution through a transparent window, a hemispherical bubble with a diameter up to ${\sim}100{\mu}m$ can be formed with a lifetime in a few tens of microsecond depending on the laser power and the focal-spot size. Parametric study has been performed to reveal the effect of laser pulse width, output power, ink concentration, and color on the bubble dynamics. The results show that the bubble generated by a laser pulse is largely similar to that produced by a thin-film heater. Consequently, the present work demonstrates the feasibility of developing a laser-actuated droplet generation mechanism for applications in ink-jet print heads. Furthermore, the results of this work indicate that the droplet generation frequency is likely to be further increased by optimizing the process parameters.

• Journal of Korean Neurosurgical Society
• /
• v.39 no.6
• /
• pp.471-474
• /
• 2006

Objective : Neuroimaging data are of paramount importance in making correct diagnosis. We herein evaluate the clinical usefulness of image transfer using cellular phones to facilitate neurological diagnosis and decision-making. Methods : Selected images from CT, MRI scans, and plain films obtained from 50 neurosurgical patients were transferred by cellular phones. A cellular phone with a built-in 1,300,000-pixel digital camera was used to capture and send the images. A cellular phone with a 262,000 color thin-film transistor liquid crystal display was used to receive the images. Communication between both cellular phones was operated by the same wireless protocol and the same wireless internet service. We compared the concordance of diagnoses and treatment plans between a house staff who could review full-scale original films and a consultant who could only review transferred images. These finding were later analyzed by a third observer. Results : The mean time of complete transfer was $2{\sim}3\;minutes$. The quality of all images received was good enough to make precise diagnosis and to select treatment options. Transferred images were helpful in making correct diagnosis and decision making in 49/50 [98%] cases. Discordant result was caused in one patient by improper selection of images by the house staff. Conclusion : The cellular phone system was useful for image transfer and delivery patient's information, leading to earlier diagnosis and initiation of treatment. This usefulness was due to sufficient resolution of the built-in camera and the TFT-LCD, the user-friendly features of the devices, and their low cost.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2003.05a
• /
• pp.41-41
• /
• 2003

텅스텐(W)은 높은 thermal stability 와 process compatibility 및 우수한 corrosion r resistance 둥으로 integrated circuit (IC)의 gate 및 interconnection 둥으로의 활용이 대두되고 있으며, 차세대 thin film transistor liquid crystal display (TFT-LCD)의 gate 및 interconnection m materials 둥으로 사용되고 았다. 그러나, 이러한 장점을 가지고 있는 팅스텐 박막이 실제 공정상에 적용되가 위해서는 건식 식각이 주로 사용되는데, 이는 wet chemical 을 이용한 습식 식각을 사용할 경우 낮은 etch rate, line width 의 감소 및 postetch residue 잔류 동의 문제가 발생하기 때문이다. 또한 W interconnection etching 을 하기 위해서는 높은 텅스텐 박막의 etch rate 과 하부 layer ( (amorphous silicon 또는 poly-SD와의 높은 etch selectivity 가 필수적 이 라 할 수 있다. 그러 나, 지금까지 연구되어온 결과에 따르면 텅스탠과 하부 layer 와의 etch selectivity 는 2 이하로 매우 낮게 관찰되고 았으며, 텅스텐의 etch rate 또한 150nm/min 이하로 낮은 값을 나타내고 있다. 따라서 본 연구에서는 halogen-based inductively coupled plasma 를 이용하여 텅스텐 박막 식각시 여러 가지 첨가 가스에 따른 높은 텅스탠 박막의 etch rate 과 하부 layer 와의 높은 etch s selectivity 를 얻고자 하였으며, 그에 따른 식각 메커니즘에 대하여 알아보고자 하였다. $CF_4/Cl_2$ gas chemistry 에 첨 가 가스로 $N_2$와 Ar을 첨 가할 경 우 텅 스텐 박막과 하부 layer 간의 etch selectivity 증가는 관찰되지 않았으며, 반면에 첨가 가스로 $O_2$를 사용할 경우, $O_2$의 첨가량이 증가함에 따라 etch s selectivity 는 계속적으로 증가렴을 관찰할 수 있었다. 이는 $O_2$ 첨가에 따라 형성되는 WOF4 에 의한 텅스텐의 etch rates 의 감소에 비하여, $Si0_2$ 등의 형성에 의한 poly-Si etch rates 이 더욱 크게 감소하였기 때문으로 사료된다. W 과 poly-Si 의 식각 특성을 이해하기 위하여 X -ray photoelectron spectroscopy (XPS)를 사용하였으며, 식각 전후의 etch depth 를 측정하기 위하여 stylus p pmfilometeT 를 이용하였다.

• Journal of Adhesion and Interface
• /
• v.20 no.3
• /
• pp.110-115
• /
• 2019

Graphene oxide has been gathering interests as a way to exfoliate graphene. Since the oxidation group of graphene oxide can hydrogen bond with various functional groups, tremendous efforts have been actively conducted to apply various applications. However, graphene oxide alone cannot substantially possess the mechanical properties required for the practical application. Therefore, in this study, polydopamine, which is a bio-mimetic mussel protein-inspired material, was combined with graphene oxide to form a large-area composite membrane at the liquid-gas interface. In addition, the morphology of the polydopamine-graphene oxide composite thin film was also controlled to obtain a composite membrane having a nano-wrinkle structure. It can be expected to be used in the next generation seawater desalination membranes or carbon composites because it can form mechanically superior and sophisticated nanostructures.

• Journal of Ocean Engineering and Technology
• /
• v.35 no.1
• /
• pp.38-49
• /
• 2021

Slug flow is the most common multi-phase flow encountered in oil and gas industry. In this study, the hydrodynamic features of flow in pipes investigated numerically using computational fluid dynamic (CFD) simulations for the effect of slug flow on the vertical and bent pipeline. The compressible Reynold averaged Navier-Stokes (RANS) equation was used as the governing equation, with the volume of fluid (VOF) method to capture the outline of the bubble in a pipeline. The simulations were tested for the grid and time step convergence, and validated with the experimental and theoretical results for the main hydrodynamic characteristics of the Taylor bubble, i.e., bubble shape, terminal velocity of bubble, and the liquid film velocity. The slug flow was simulated with various air and water injection velocities in the pipeline. The simulations revealed the effect of slug flow as the pressure occurring in the wall of the pipeline. The peak pressure and pressure oscillations were observed, and those magnitudes and trends were compared with the change in air and water injection velocities. The mechanism of the peak pressures was studied in relation with the change in bubble length, and the maximum peak pressures were investigated for the different positions and velocities of the air and water in the pipeline. The pressure oscillations were investigated in comparison with the bubble length in the pipe and the oscillation was provided with the application of damping. The pressures were compared with the case of a bent pipe, and a 1.5 times higher pressures was observed due to the compression of the bubbles at the corner of the bent. These findings can be used as a basic data for further studies and designs on pipeline systems with multi-phase flow.

• Journal of Powder Materials
• /
• v.29 no.3
• /
• pp.240-246
• /
• 2022

Novel Ni- and Fe-based alloys are developed to impart improved mechanical properties and corrosion resistance. The designed alloys are manufactured as a powder and deposited on a steel substrate using a high-velocity oxygen-fuel process. The coating layer demonstrates good corrosion resistance, and the thus-formed passive film is beneficial because of the Cr contained in the alloy system. Furthermore, during low-temperature heat treatment, factors that deteriorate the properties and which may arise during high-temperature heat treatment, are avoided. For the heattreated coating layers, the hardness increases by up to 32% and the corrosion resistance improves. The influence of the heat treatment is investigated through various methods and is considered to enhance the mechanical properties and corrosion resistance of the coating layer.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2001.11a
• /
• pp.68-68
• /
• 2001

Thin films of polycrystalline silicon (poly-Si) is a promising material for use in large-area electronic devices. Especially, the poly-Si can be used in high resolution and integrated active-matrix liquid-crystal displays (AMLCDs) and active matrix organic light-emitting diodes (AMOLEDs) because of its high mobility compared to hydrogenated _amorphous silicon (a-Si:H). A number of techniques have been proposed during the past several years to achieve poly-Si on large-area glass substrate. However, the conventional method for fabrication of poly-Si could not apply for glass instead of wafer or quartz substrate. Because the conventional method, low pressure chemical vapor deposition (LPCVD) has a high deposition temperature ($600^{\circ}C-1000^{\circ}C$) and solid phase crystallization (SPC) has a high annealing temperature ($600^{\circ}C-700^{\circ}C$). And also these are required time-consuming processes, which are too long to prevent the thermal damage of corning glass such as bending and fracture. The deposition of silicon thin films on low-cost foreign substrates has recently become a major objective in the search for processes having energy consumption and reaching a better cost evaluation. Hence, combining inexpensive deposition techniques with the growth of crystalline silicon seems to be a straightforward way of ensuring reduced production costs of large-area electronic devices. We have deposited crystalline poly-Si thin films on soda -lime glass and SiOz glass substrate as deposited by PVD at low substrate temperature using high power, magnetron sputtering method. The epitaxial orientation, microstructual characteristics and surface properties of the films were analyzed by TEM, XRD, and AFM. For the electrical characterization of these films, its properties were obtained from the Hall effect measurement by the Van der Pauw measurement.