• Transactions on Electrical and Electronic Materials
• /
• 제10권4호
• /
• pp.131-134
• /
• 2009

The electrical properties and the microstructure of nitrogen-doped poly 3C-SiC films used for micro thermal sensors were studied according to different thicknesses. Poly 3C-SiC films were deposited by LPCVD (low pressure chemical vapor deposition) at $900^{\circ}C$ with a pressure of 4 torr using $SiH_2Cl_2$ (100%, 35 sccm) and $C_2H_2$ (5% in $H_2$, 180 sccm) as the Si and C precursors, and $NH_3$ (5% in $H_2$, 64 sccm) as the dopant source gas. The resistivity of the poly SiC films with a 1,530 ${\AA}$ thickness was 32.7 ${\Omega}-cm$ and decreased to 0.0129 ${\Omega}-cm$ at 16,963 ${\AA}$. The measurement of the resistance variations at different thicknesses were carried out within the $25^{\circ}C$ to $350^{\circ}C$ temperature range. While the size of the resistance variation decreased when the films thickness increased, the linearity of the resistance variation improved. Micro heaters and RTD sensors were fabricated on a $Si_3N_4$ membrane by using poly 3C-SiC with a 1um thickness using a surface MEMS process. The heating temperature of the SiC micro heater, fabricated on 250 ${\mu}m$${\times}$250 ${\mu}m$ $Si_3N_4$ membrane was $410^{\circ}C$ at an 80 mW input power. These 3C-SiC heaters and RTD sensors, fabricated by surface MEMS, have a low power consumption and deliver a good long term stability for the various thermal sensors requiring thermal stability.

• 신재생에너지
• /
• 제18권1호
• /
• pp.29-34
• /
• 2022

The most prevalent cause of solar cell efficiency loss is reduced recombination at the metal electrode and silicon junction. To boost efficiency, a a SiO_X/poly-Si passivating interface is being developed. Poly-Si for passivating contact is formed by various deposition methods (sputtering, PECVD, LPCVD, HWCVD) where the ploy-Si characterization depends on the deposition method. The sputtering process forms a dense Si film at a low deposition rate of 2.6 nm/min and develops a low passivation characteristic of 690 mV. The PECVD process offers a deposition rate of 28 nm/min with satisfactory passivation characteristics. The LPCVD process is the slowest with a deposition rate of 1.4 nm/min, and can prevent blistering if deposited at high temperatures. The HWCVD process has the fastest deposition rate at 150 nm/min with excellent passivation characteristics. However, the uniformity of the deposited film decreases as the area increases. Also, the best passivation characteristics are obtained at high doping. Thus, it is necessary to optimize the doping process depending on the deposition method.

• 센서학회지
• /
• 제18권2호
• /
• pp.147-153
• /
• 2009

A thermal flow sensor has been fabricated and characterized, consisting of a center resistive heater surrounded by two upstream and one downstream temperature sensing resistors. The heater and temperature sensing resistors are fabricated from nitrogen-doped(n-type) polycrystalline silicon carbide(poly-SiC) deposited by LPCVD(low pressure chemical vapor deposition) on LPCVD silicon nitride films on a Si substrate. Cavities were etched into the Si substrate from the front side to create suspended silicon nitride membranes carrying the poly-SiC elements. One upstream sensor is located $50{\mu}m$ from the heater and has a sensitivity of $0.73{\Omega}$/sccm with ${\sim}15\;ms$ rise time in a dynamic range of 1000 sccm. N-type poly-SiC has a linear negative temperature coefficient and a TCR(temperature coefficient of resistance) of $-1.24{\times}10^{-3}/^{\circ}C$ from room temperature to $100^{\circ}C$.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권1호
• /
• pp.24-29
• /
• 2000

We propose a simple method to control the crystallization depth of amorphous silicon (a-Si) deposited by PECVD or LPCVD during the excimer laser annealing (ELA). Employing the new method, we have formed poly-Si/a-Si double film and fabricated a new poly-Si TFT with vertical a-Si offsets between the poly-Si channel and the source/drain of TFT without any additional photo-lithography process. The maximum leakage current of the new poly-Si TFT decreased about 80% due to the highly resistive vertical a-Si offsets which reduce the peak electric field in drain depletion region and suppress electron-hole pair generation. In ON state, current flows spreading down through broad a-Si cross-section in the vertical a-Si offsets and the current density in the drain depletion region where large electric field is applied is reduced. The stability of poly-Si TFT has been improved noticeably by suppressing trap state generation in drain region which is caused by high current density and large electric field. For example, ON current of the new TFT decreased only 7% at a stress condition where ON current of conventional TFT decreased 89%.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.356-356
• /
• 2010

In this paper, Poly silicon thin-film transistors (poly-Si TFTs) with employed the SPC (Solid phase crystallization) and ELA (Excimer laser annealing) methods on glass panel substrate are fabricated to investigate the electrical poperies. Poly-Si TFTs have recess-channel structure with formated source/drain regions by LPCVD n+ poly Si in low $650^{\circ}C$ temperature. the ELA-TFT show higher on/off current ratio and subthreshold swing than a-Si and SPC TFT that therefore, these results showed that the ELA-TFT might be beneficial for practical embedded TFT memory device application.

• 한국진공학회지
• /
• 제11권1호
• /
• pp.16-21
• /
• 2002

$Si_2H_6$가스를 이용한 LPCVD내에서의 실리콘의 선택적 에피텍시 성장을 $1000^{\circ}C$ 이하의 초청정 분위기하의 저온에서 수행하였다. HCI 첨가없이 초청정 공정으로 인한 양질의 에피텍시 Si층이 균일하게 얻어 졌으며, $SiO_2$위에 증착된 실리콘의 잠복기를 발견할 수 있었다. 단결정위의 에피텍시 층은 산화물 층위 보다 더 두껍게 증착되었다. 산소첨가로 잠복기가 20~30초간 증가하였다. 증착된 박막의 절단면과 표면 형상은 SEM으로 관찰되었으며, XRD를 통해 막질을 평가하였다.

• 한국세라믹학회지
• /
• 제41권9호
• /
• pp.637-641
• /
• 2004

We investigated the effects of SiH$_4$ gas on the surface of Hf-silicate films during the deposition of polycrystalline (poly) Si films and the thermal stability of sputtered Hf-silicate films in poly Si/Hf-silicate structure by using High Resolution Transmission Electron Microscopy (HR-TEM) and X-ray Photoelectron Spectroscopy (XPS). Hf-silicate films were deposited by using DC-mag-netron sputtering with Hf target and Si target and poly Si films were deposited at 600$^{\circ}C$ by using Low Pressure Chemical Vapor Deposition (LPCVD) with SiH$_4$ gas. After poly Si film deposition at 600$^{\circ}C$, Hf silicide layer was observed between poly Si and Hf-silicate films due to the reaction between active SiH$_4$ gas and Hf-silicate films. After annealing at 900$^{\circ}C$, Hf silicide, formed during the deposition of poly Si, changed to Hf-silicate and the phase separation of the silicate was not observed. In addition, the Hf-silicate films remain amorphous phase.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.144-144
• /
• 2010

다결정 실리콘 박막트랜지스터 (poly-Si TFTs)는 벌크실리콘을 이용한 MOSFET소자에 비해 실리콘 박막의 형성이 간단하므로 대면적의 공정이 가능하며 다양한 기판위에 적용이 가능하여 LCD, OLED 등의 디스플레이 기기에 많이 이용되고 있다. 또한 poly-Si TFT는 3차원으로 적층된 소자의 제작이 가능하여 고집적의 한계를 극복할 소자로 주목받고 있다. 최근, DRAM은 캐패시터의 축소화와 구조적 공정이 한계점에 도달했으며 이를 극복하기 위하여 SOI 기판을 사용한 하나의 트랜지스터로 DRAM의 동작을 수행하는 1T-DRAM의 연구가 활발히 진행 중이다. 이러한 1T-DRAM 소자를 대면적과 다층구조의 공정이 가능한 poly-Si TFT를 이용하여 구현하면 초고집적의 메모리 소자를 제작 가능할 것이다. 따라서, 본 연구에서는 다결정 실리콘 박막트랜지스터 (poly-Si TFTs)를 이용한 1T-DRAM의 동작 특성을 연구하였다. 소자의 제작 방법으로는 200 nm의 열산화막이 성장된 p-type 실리콘 기판위에 상부실리콘으로 사용될 비정질 실리콘 박막을 LPCVD 방법으로 증착하였다. 다음으로 248 nm의 파장을 가지는 KrF 레이저를 이용한 eximer laser annealing (ELA) 공정을 통하여 결정화된 상부실리콘층에 TFT 소자를 제작하여 전기적 특성을 평가하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.408-409
• /
• 2006

The polycrystalline 3C-SiC thin films heteroepitaxially grown by LPCVD method using single precursor 1. 3-disilabutane at $850^{\circ}C$. The crystallinity of the 3C-SiC thin film. was analyzed by XPS. Residual strain was investigated by Raman scattering. The surface morphology and voids between SiC and $SiO_2$ were measured by SEM. The grown poly 3C-SiC thin film is very good crystalline quality, surface like mirror, and low defect and strain. Therefore, the polycrystalline 3C-SiC is suitable for harsh environment MEMS applications.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2008년도 하계종합학술대회
• /
• pp.489-490
• /
• 2008

As anodizing method using poly-Si (polycrystalline silicon) grown by LPCVD (Low Pressure Chemical Vapor Deposition), a ballistic electron emitter was made. An OPPS (Oxidized Porous Poly-Si) structure can generate ballistic electron which can pass through without scattering owing to electric field of oxide layer wrapped around nanocrystal due to applied voltage of between surface and bottom electrode. As electrode, (Al, Au and Pt/ti) were used. In this case, there were the better characteristics in Al and Pt/ti than in Al and Au.