• 제목/요약/키워드: LED(Light Emitted Diode)

Search Result 30, Processing Time 0.033 seconds

Thermal Flow Analysis for Development of LED Fog Lamp for Vehicle (차량 LED 안개등 개발을 위한 열유동 해석)

  • Lee, Suk Young
    • Journal of Energy Engineering
    • /
    • v.28 no.4
    • /
    • pp.35-41
    • /
    • 2019
  • In order to overcome these disadvantages, the halogen light source, which was previously used as a vehicle fog light, has increased power consumption and a short lifetime, and thus, an automobile light source is gradually being replaced with an LED. However, when the vehicle LED fog light is turned on, there is a disadvantage in reducing the life of the fog lamp due to the high heat generated from the LED. The heat generated by the LED inside the fog lamp is mainly emitted by the heatsink, but most of the remaining heat is released to the outside through convection. When cooling efficiency decreases due to convection, thermal energy generates heat to lenses, reflectors, and bezels, which are the main parts of lamps, or generates high temperatures in LED, thereby shortening the life of LED fog lights. In this study, we tried to improve the heat dissipation performance by convection in addition to the heat dissipation method by heat sink, and to determine the installation location of vents that can discharge the internal air or intake the external air of LED fog lamp for vehicle. Thermal fluid analysis was performed to ensure that the optimal data were reflected in the design. The average velocity of air increased in the order of Case3 and Case2 compared to Case1, which is the existing prototype, and the increase rate of Case3 was relatively higher than that of other cases. This is because the vents installed above and below the fog lamps induce the convective phenomena generated according to the temperature difference, and the heat is efficiently discharged with the increase of the air speed.

Influence of Blue-Emission Peak Wavelength on the Reliability of LED Device (청색 피크 파장이 LED 소자에 미치는 영향)

  • Han, S.H.;Kim, Y.J.;Kim, J.H.;Jung, J.Y.;Kim, H.C.;Cho, G.S.
    • Journal of the Korean Vacuum Society
    • /
    • v.21 no.3
    • /
    • pp.164-170
    • /
    • 2012
  • The dependance of degradation on the blue-peak wavelength is investigated with the blue light-emitting diode (LED) of InGaN/GaN with respect to the optical and the electrical characteristics of the devices. The LED devices emitting the blue-peak wavelength ranging from 437 nm to 452 nm is prepared to be stressed for a long aging time with three different currents of 60 mA, 75 mA and 90 mA, respectively. The degradation of optical intensity is observed with and without phosphor in the devices. The device without phosphor has been degraded significantly as the wavelength of blue-peak is decreased while the optical intensity of LED device with phosphor become less sensitive than that of device without phosphor. The electrical property does not depend on the emission peak wavelength. However, the series-resistance of LED device is slowly increased as the aging time is increased. The deformation of device is observed severely the short wavelength of blue-peak even with the same current since the short wavelength is absorbed substantially at the materials of device during the aging time. Consequently, in order to enhance the lifetime of LED devices, it is important to understand the optical degradation property of the materials against the specific wavelengths emitted from the blue chip.

A Study on Machining Electrode for LED Mold with Shaped End-Mill (형상 엔드밀 공구를 이용한 LED금형의 방전전극 가공에 관한 연구)

  • Kim, Hyeong-Chan;Lee, Hui-Gwan;Hwang, Geum-Jong;Gong, Yeong-Sik;Yang, Gyun-Ui
    • Journal of the Korean Society for Precision Engineering
    • /
    • v.19 no.10
    • /
    • pp.187-194
    • /
    • 2002
  • A study on machining electrode for LED (Light Emitted Diode) mold with shaped end-mill is presented. The electrode machining by shaped end-mill has been used for maximizing the productivity in manufacturing semiconductor mold. However, it has not been researched systematically for many difficulties such as the making of shaped end-mill, generation of tool path due to distinctive tool geometry, and so on. Tool path is generated on geometry of the shaped end-mill and cutting force to provide accurate and efficient machining of electrode. The verification program can drive enhancement of productivity, selecting cutting conditions from experiment function of cutting force. Also, compensation of tooling and maching error can make the electrode accurately by modifying tool path. Therefore, the research on machining with shaped end-mill can contribute to enhancement of accuracy and productivity in building semiconductor mold.

A Study on the Optimal Position of Vehicle Side Mirrors according to the Perception of Visual Information (시각정보의 인식도에 의한 자동차 Side Mirror의 최적 위치결정에 관한 연구)

  • 김도회;이근희
    • Journal of Korean Society of Industrial and Systems Engineering
    • /
    • v.14 no.24
    • /
    • pp.123-132
    • /
    • 1991
  • This study deals with the experiment of perceiving visual information according to the positions of vehicle side mirrors. In the design of vehicle, the consideration of safety is very important. Therefore we consider the positions of side mirrors to use visual information effectively which is important factor to driver. This paper presents the position of side mirror to elevate the degree of visual perception for the circumstances of danger by experiments. To exhibit the circumstances of danger. 4 LED(Light Emitted Diode) art located at each side(right. left front. hack) of vehicle. A subject pushes the LED switch to see that if he perceives the circumstance of danger. To record the circumstance of randomly generated danger, computer interface card is used to control 4 LED and swithch on IBM PC/AT Experiments are divided into 2 parts. The 1st experiment present the independence of right & left side mirror. The 2nd experiment present optimal position of right & left side mirror. The vehicle used in experiment is model EL of H Co.. Statistical process of experimental data using SPSS(Statistical Package for Social Sciences)/PC package concludes that 1) the optimal position of right side mirror is 54cm forward of exist position. 2) for the left side mirror, the position of 120cm forward of exist position shows the worst degree of perception. and the optimal position does not exist in statistical meaning.

  • PDF

Effect of Light Wavelengths on the Mycelial Browning of Lentinula edodes Strain Sanjo 701ho (광 파장이 표고 품종 산조 701호 균사의 갈변에 미치는 영향)

  • Seo, Dong-Seok;Koo, Chang-Duck
    • The Korean Journal of Mycology
    • /
    • v.47 no.1
    • /
    • pp.63-73
    • /
    • 2019
  • Mycelial browning, which protects the organism from contamination and moisture loss, is essential for sawdust cultivation of Lentinula edodes. The effects of light and light wavelengths on the mycelial browning of the L. edodes Sanjo 701ho strain, and the characteristics of its brown hyphae, were investigated. After the mycelia were cultured on potato dextrose agar medium under fluorescent lamps covered with colored cellophane filters (red, green, and blue) or under light emitted diodes (LED), with wavelengths ranging from 400 to 700 nm (far-red, red, green, and blue), for 14 h per day for 40 days, the mycelial browning rate was measured. The wavelength of fluorescent lamps, which range from 300 to 1,100 nm, was reduced to 360 to 1,022 nm with the use of three colored cellophane filters and the photosynthetic photon flux density was reduced by 42 to 71 % depending on the light wavelength. The browning rate by colony area of mycelia exposed to light was at an average of 64 %, whereas, that of unexposed mycelia was only 5 %. The browning rate was 0.02 % in far-red, 1.5 % in red, 53.8 % in green, 57.3 % in blue, and 64.0 % in fluorescent light. The white mycelia were resilient with actively growing hyphae, filled with cytoplasm, and thin cell walls less than $1{\mu}m$ thick. Conversely, the brown mycelia possessed dead, hard hyphal structures without cytoplasm, but with approximately $2-4{\mu}m-thick$-thick cell walls. In conclusion, lights of varying wavelengths, especially short-wavelength LEDs, are effective for forming dead, brown mycelia of L. edodes, thus, forming a protective functional layer for its living white mycelia.

Quality Characteristics of Pleurotus eryngii Cultivated with Different Wavelength of LED Lights (LED광의 파장을 달리하여 재배한 새송이버섯의 품질특성)

  • Kim, Do-Hee;Choi, Hye-Jin;Jo, Woo-Sik;Moon, Kwang-Deog
    • Food Science and Preservation
    • /
    • v.19 no.3
    • /
    • pp.354-360
    • /
    • 2012
  • The effect of the wavelength of the light emitted by the light-emitting diode (LED) on the growth characteristics and physicochemical and sensory qualities of Pleurotus eryngii were investigated. Pleurotus eryngii were grown under different light sources: blue light (450 nm), red light (650 nm), green light (525 nm), UV-A (365 nm), and mixed light ($B^*R$, $B^*G$, $R^*G$, $B^*R^*G^*UV-A$). The quantity of LED light was set up at 50% (LED: 64.9-108.0 $pmolm-2{\cdot}s-1$;fluorescentlight:11.7lux). Fluorescent light was used as control. There were no significant differences in the flesh firmness. In the case of the Pleurotuseryngii cultivated under red, green, and mixed light ($R^*G$), the color of the pileus and the length of the stipe were similar to those of the control group. The sensory scores were not significantly different between the LED lights (red, green, and $R^*G$) and the control. Among the three LED light conditions, the sample cultivated under red light recorded the highest score. The samples under UV-A, blue, and mixed light ($B^*R$, $B^*G$, $B^*R^*G^*U$) had a dark pileus color and had a short stipe. These results showed that the wavelength of LED light affected the growth and quality characteristics of Pleurotus eryngii, and that using red LED light is preferable for the cultivation of Pleurotus eryngii with better quality.

EFFECT OF VARIOUS LINERS ON THE POLYMERIZATION SHRINKAGE OF COMPOSITE RESIN (수종의 이장재가 복합레진의 중합수축에 미치는 영향)

  • Choi, Ji-Won;Lee, Sang-Ho;Lee, Nan-Young
    • Journal of the korean academy of Pediatric Dentistry
    • /
    • v.33 no.4
    • /
    • pp.606-614
    • /
    • 2006
  • The purpose of this study was to evaluate the polymerization contraction of composite resin(Tetric $ceram^{(R)}$, Ivoclar Vivadent Liechtenstein) according to various liners(Tetric $flow^{(R)}$, Ivoclar Vivadent, Liechtenstein/$Ionosit^{(R)}$, DMG, German/ $Vitrebond,^{TM}$ 3M-ESPE, USA). The strain gauge method was used for measurement of polymerization shrinkage strain. Specimens were divided by 8 groups according to curing units and liners. Group A, E: Tetric $ceram^{(R)}$ bulk filing, Group B, F: Tetric $flow^{(R)}$ lining, Tetric $ceram^{(R)}$ filling, Group C, G: $Ionosit^{(R)}$ lining, Tetric $ceram^{(R)}$ filling, Group D, H: $Vitrebond^{TM}$ lining, Tetric $ceram^{(R)}$ filling. Group A, B, C and D were cured using the conventional halogen light($XL3000^{TM}$ 3M ESPE, USA) for 40 seconds at $400mW/cm^2$. Group E, F G and H were cured using light emitted diode(LED) light(Elipar Freelight $2^{TM}$, 3M-ESPE, USA) for 15 seconds at 800 $mW/cm^2$. Strain gauge attached to each sample was connected to a strainmeter. Measurements were recorded at each second for the total of 750 seconds including the periods of light application. Obtained data were analyzed statistically using Repeated measures ANOVA and Tukey test. The results of this were as follows : 1. Contraction stresses in flowable resin and glass ionomer lining group were lower than that in compomer lining group(p<0.05). 2, Contraction stresses in LED curing light groups were higher than that in halogen curing light groups, but there was no significant difference (p>0.05).

  • PDF

Laser Micro-drilling of Sapphire/silicon Wafer using Nano-second Pulsed Laser (나노초 펄스 레이저 응용 사파이어/실리콘 웨이퍼 미세 드릴링)

  • Kim, Nam-Sung;Chung, Young-Dae;Seong, Chun-Yah
    • Journal of the Korean Society for Precision Engineering
    • /
    • v.27 no.2
    • /
    • pp.13-19
    • /
    • 2010
  • Due to the rapid spread of mobile handheld devices, industrial demands for micro-scale holes with a diameter of even smaller than $10{\mu}m$ in sapphire/silicon wafers have been increasing. Holes in sapphire wafers are for heat dissipation from LEDs; and those in silicon wafers for interlayer communication in three-dimensional integrated circuit (IC). We have developed a sapphire wafer driller equipped with a 532nm laser in which a cooling chuck is employed to minimize local heat accumulation in wafer. Through the optimization of process parameters (pulse energy, repetition rate, number of pulses), quality holes with a diameter of $30{\mu}m$ and a depth of $100{\mu}m$ can be drilled at a rate of 30holes/sec. We also have developed a silicon wafer driller equipped with a 355nm laser. It is able to drill quality through-holes of $15{\mu}m$ in diameter and $150{\mu}m$ in depth at a rate of 100holes/sec.

Study on Wireless Control of a Board Robot Using a Sensing Glove (장갑 센서를 이용한 보드로봇의 무선제어 연구)

  • Ryu, Jaemyung;Kim, Dong Hun
    • Journal of the Korean Institute of Intelligent Systems
    • /
    • v.23 no.4
    • /
    • pp.341-347
    • /
    • 2013
  • This study presents the remote control of a board robot using a Sensing glove based on Bluetooth communication. The board robot is a kind of riding robot controlled by an user. The user wears the proposed remote glove controller, and changes a direction of the robot by different kinds of finger actions. Bluetooth is used for wireless communication between the board robot and its user. CdS cell Sensors and a LED in the glove are used for recognition of a number of finger actions, which are measured as analog signals. The finger actions have five commands ('1'right '2'neutrality '3'left '4'operation '5'stop), which are transmitted from the user to the board robot through Bluetooth communication. Experimental results show that proposed a Sensing glove can effectively control the board robot.

Inverted CdSe/ZnS Quantum Dots Light-Emitting Diode Using Low-Work Function Organic Material Polythylenimine Ethoylated

  • Kim, HongHee;Son, DongIck;Jin, ChangKyu;Hwang, DoKyung;Yoo, Tae-Hee;Park, CheolMin;Choi, Won Kook
    • Proceedings of the Korean Vacuum Society Conference
    • /
    • 2014.02a
    • /
    • pp.246.1-246.1
    • /
    • 2014
  • Over the past several years, colloidal core/shell type quantum dots lighting-emitting diodes (QDLEDs) have been extensively studied and developed for the future of optoelectronic applications. In the work, we fabricate an inverted CdSe/ZnS quantum dot (QD) based light-emitting diodes (QDLED). In order to reduce work function of indium tin oxide (ITO) electrode for inverted structure, a very thin (<10 nm) polyethylenimine ethoxylated (PEIE) is used as surface modifier[1] instead of conventional metal oxide electron injection layer. The PEIE layer substantially reduces the work function of ITO electrodes which is estimated to be 3.08 eV by ultraviolet photoemission spectroscopy (UPS). From transmission electron microscopy (TEM) study, CdSe/ZnS QDs are uniformly distributed and formed by a monolayer on PEIE layer. In this inverted QDLEDs, blend of poly (9,9-di-n-octyl-fluorene-alt-benzothiadiazolo) and poly(N,N'-bis(4-butylphenyl)-N,N'-bis(phenyl)benzidine] are used as hole transporting layer (HTL) to improve hole transporting property. At the operating voltage of 8 V, the QDLED device emitted spectrally orange color lights with high luminance up to 2450 cd/m2, and showed current efficacy of 0.6 cd/A, respectively.

  • PDF