• Structural Engineering and Mechanics
• /
• v.44 no.6
• /
• pp.815-837
• /
• 2012

A plated beam is strengthened by bonding a thin plate to the tension face; it often fails because of premature debonding of the thin plate from the original beam in a brittle manner. A sound understanding of the mechanism of such debonding failure is very important for the effective use of this strengthening technique. This paper presents an improved analytical solution for interfacial stresses that incorporates multiple loading conditions simultaneously, including prestress, mechanical and thermal loads, and the effects of adherend shear deformations and curvature mismatches between the beam and the plate. Simply supported beams bonded with a thin prestressing plate and subjected to both mechanical and thermal loading were considered in the present work. The effects of the curvature mismatch and adherend shear deformations of the beam and plate were investigated and compared. The main mechanisms affecting the distribution of interfacial stresses were analyzed. Both the normal and shear stresses were found to be significantly influenced by the coupled effects of the elastic moduli with the ratios $E_a/E_b$ and $E_a/E_p$.

• Advances in materials Research
• /
• v.7 no.2
• /
• pp.83-103
• /
• 2018

In this paper, the problem of interfacial stresses in damaged reinforced concrete beams strengthened with bonded prestressed functionally graded material plate and subjected to a uniformly distributed load, arbitrarily positioned single point load, or two symmetric point loads is developed using linear elastic theory. The adopted model takes into account the adherend shear deformations by assuming a linear shear stress through the depth of the damaged RC beam. This solution is intended for application to beams made of all kinds of materials bonded with a thin FGM plate. The results show that there exists a high concentration of both shear and normal stress at the ends of the functionally graded material plate, which might result in premature failure of the strengthening scheme at these locations. Finally, numerical comparisons between the existing solutions and the present new solution enable a clear appreciation of the effects of various parameters of the beams on the distributions of the interfacial stresses.

• Advances in materials Research
• /
• v.11 no.2
• /
• pp.91-109
• /
• 2022

This paper presents a closed-form higher-order analysis of interfacial shear stresses in RC continuous beams strengthened with bonded prestressed laminates. For retrofitting reinforced concrete continuous beams is to bond fiber reinforced prestressed composite plates to their tensile faces. An important failure mode of such plated beams is the debonding of the composite plates from the concrete due to high level of stress concentration in the adhesive at the ends of the composite plate. The model is based on equilibrium and deformations compatibility requirements in and all parts of the strengthened beam, where both the shear and normal stresses are assumed to be invariant across the adhesive layer thickness. In the present theoretical analysis, the adherend shear deformations are taken into account by assuming a parabolic shear stress through the thickness of both the RC continuous beams strengthened with bonded prestressed laminates. The theoretical predictions are compared with other existing solutions. A parametric study has been conducted to investigate the sensitivity of interface behavior to parameters such as laminate stiffness and the thickness of the laminate where all were found to have a marked effect on the magnitude of maximum shear and normal stress in the composite member.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.11
• /
• pp.1035-1042
• /
• 2005

In the present study, the principle of minimum energy is employed to configure the shape of rivulet flowing down an inclined surface. The profile of laminar rivulet is determined by numerical integration. The maximum center thickness, which corresponds to the minimum thickness of falling film, is found to exist regardless of liquid flow rate and is compared with the analytical and experimental data. At small liquid flow rate the center thickness of rivulet and its width increase almost linearly with flow rate. Once the center thickness of rivulet becomes very close to its maximum value, its growth rate retards abruptly. However the width of rivulet increases proportionally to the liquid flow rate and most part of its free surface is as flat as that of stable film. The growth rate of rivulet thickness with respect to liquid flow rate becomes larger at bigger contact angle. The width of rivulet increases rapidly with its flow rate especially at small contact angle, As the liquid-vapor interfacial shear stress increases, the center thickness of rivulet decreases with its flow rate, which is remarkable at small contact angle. However the effect of interfacial shear stress on the width of rivulet is almost negligible.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.22 no.2
• /
• pp.167-173
• /
• 1996

The stability of gel structured emulsion and the effect of polyols on it have been studied by rheological property and interfacial tension. In this paper, three types of gel structured emulsions were prepared by using three polyols respectively(glycerine for sample 1, 1.3 BG for sample 2, PG for sample 3). And both complex modulus($G^*$) and loss angle[$\delta$ = tan-1(G"/G')] of samples were investigated against oscillating shear stress and frequency($\omega$). The results show sample 1 is most highly consistent with oscillating shear stress. And the results were compared with those of accelerated tests concerning storage stability of gel structured emulsion. To correlate consistency of rheological property with storage stability, interfacial tension from which adsorption efficiency of surfactant(Octyldodecyl Ether) could be known was measured. Sample 1 showed the largest value of [$d{\gamma}/dIn_{Cconc. of surfactant}$] in Gibbs equation. In summary, the prediction of stability could be correctly made by the consistency of rheological property(G*,$\gamma$) of gel structured emulsion against oscillating shear stress and it could be supported by measuring interfacial tension. And polyol affected the value of [$d{\gamma}/dIn_{Cconc. of surfactant}$], consequently affected the stability.lity.

• KCI Concrete Journal
• /
• v.12 no.1
• /
• pp.113-120
• /
• 2000

This paper presents the behavior and strengthening effect of reinforced concrete rectangular beams strengthened using CFRP sheets with different strengthening level. In general, normally strengthened beams are failed by interfacial shear failure (delamination) within concrete, instead of by tensile failure of the CFRP sheets. The delamination occurred suddenly and the concrete cover cracked vertically by flexure was spalled off due to the release energy. The strengthened beams were stiffer than the control beam before and after reinforcement yielding. The ultimate load considerably increased with an increase of strengthening level, while the ultimate deflection significantly decreased. The tensile force of CFRP sheets and average shear stress of concrete at delamination failure were curvilinearly proportional to the strengthening level. Therefore, the increment of ultimate load obtained by strengthening was curvilinearly proportional to the strengthening level. The averaged horizontal shear stress of concrete at the interface ranges between (equation omitted) and (equation omitted) (in kg/$\textrm{cm}^2$) depending on strengthening level.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.7
• /
• pp.1384-1392
• /
• 2002

Single fiber pull-out technique has been commonly used to characterize the mechanical behavior of interface in fiber reinforced composite materials. An improved analysis considering the effects of transversely isotropic properties of fiber and the effects of thermal residual stresses in both radial and axial directions along the fiber/matrix interface is developed for the single fiber pull-out test. Although the stress transfer properties across the interface is not much affected by considering the transversely isotropic properties of fiber, interfacial debonding is notably encouraged by the effect. The interfacial shear stress that plays an important role in interfacial debonding is very much affected by the component of axial thermal residual stress in the bonded region, which can induce a two-way debonding mechanism.

• Steel and Composite Structures
• /
• v.20 no.6
• /
• pp.1275-1303
• /
• 2016

Steel plates and carbon-fiber-reinforced polymer (CFRP) laminates or plates bonded to concrete substrates have been widely used for concrete strengthening. However, this technique cause plate debonding, which makes the strengthening system inefficient. The main objective of this study is to enhance the bond strength of externally bonded steel plates and CFRP laminates to the concrete surface by proposing new embedded adhesive and steel connectors. The effects of these new embedded connectors were investigated through the tests on 36 prism specimens. Parameters such as interfacial shear stress, fracture energy and the maximum strains in plates were also determined in this study and compared with the maximum value of debonding stresses using a relevant failure criterion by means of pullout test. The study indicates that the interfacial bond strength between the externally bonded plates and concrete can be increased remarkably by using these connectors. The investigation verifies that steel connectors increase the shear bond strength by 48% compared to 38% for the adhesive connectors. Thus, steel connectors are more effective than adhesive connectors in increasing shear bond strength. Results also show that the use of double connectors significantly increases interfacial shear stress and decrease debonding failure. Finally, a new proposed formula is modified to predict the maximum bond strength of steel plates and CFRP laminates adhesively glued to concrete in the presence of the embedded connectors.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.8
• /
• pp.677-682
• /
• 2015

We simulate an emulsion system under simple shear rates to analyze its rheological characteristics using the lattice Boltzmann method (LBM). We calculate the relative viscosity of an emulsion under a simple shear flow along with changes in temperature, shear rate, and surfactant concentration. The relative viscosity of emulsions decreased with an increase in temperature. We observed the shear-thinning phenomena, which is responsible for the inverse proportion between the shear rate and viscosity. An increase in the interfacial tension caused a decrease in the relative viscosity of the decane-in-water emulsion because the increased deformation caused by the decreased interfacial tension significantly influenced the wall shear stress.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.10a
• /
• pp.158-162
• /
• 2001

The effects of chemical treatment on Kevlar-29 fibers have been studied in a composite system. The surface characteristics of the Kevlar-29 fibers were characterized by pH, acid-base value and X-ray photoelectron spectroscopy (XPS). The mechanical interfacial properties of final composites were studied by interlaminar shear strength (ILSS) and critical stress intensity factor ($K_{IC}$). Also, the impact properties of the composites were investigated in the differentiating studies between initiation and propagation energies, and ductile index (DI) along with maximum farce and total energy. It was found that the chemical treatment with phosphoric acid ($H_3PO_4$) solution significantly affected the degree of adhesion at interfaces between fibers and resin matrix, resulting in improving the mechanical interfacial strength of the composites. This was probably due to the presence of chemical polar groups on Kevlar surfaces, leading to an increment of interfacial binding force in a composite system.