• Journal of Electrical Engineering and Technology
• /
• v.12 no.4
• /
• pp.1566-1574
• /
• 2017

When the inter-turn short circuit (ITSC) fault occurs, the distortion of the magnetic field is serious. The motor loss variations of each part are obvious, and the motor temperature field is also affected. In order to obtain the influence of the ITSC fault on the motor temperature distribution, firstly, the normal and the fault finite element models of the permanent magnet synchronous motor (PMSM) were established. The magnetic density distribution and the eddy current density distribution were analyzed, and the mechanism of loss change was revealed. The effects of different forms and degrees of the fault on the loss were obtained. Based on the loss analysis, the motor temperature field calculation model was established, and the motor temperature change considering the loop current was analyzed. The influence of the fault on the motor temperature distribution was revealed. The sensitivity factors that limit the motor continuous operation were obtained. Finally, the correctness of the simulation was verified by experiments. The conclusions obtained are of great significance for the fault and high temperature demagnetization of the permanent magnet analysis.

• Asian Journal of Atmospheric Environment
• /
• v.11 no.4
• /
• pp.270-282
• /
• 2017

To evaluate the deposition amount on a ground surface, mesoscale numerical models coupled with atmospheric chemistry are widely used for larger horizontal domains ranging from a few to several hundreds of kilometers; however, these models are rarely applied to high-resolution simulations. In this study, the performance of a dry and wet deposition model is investigated to estimate the amount of deposition via computational fluid dynamics (CFD) models with high grid resolution. Reynolds-averaged Navier-Stokes (RANS) simulations are implemented for a cone and a two-dimensional ridge to estimate the dry deposition rate, and a constant deposition velocity is used to obtain the dry deposition flux. The results show that the dry deposition rate of RANS generally corresponds to that observed in wind-tunnel experiments. For the wet deposition model, the transport equation of a new scalar concentration scavenged by rain droplets is developed and used instead of the scalar concentration scavenged by raindrops falling to the ground surface just below the scavenging point, which is normally used in mesoscale numerical models. A sensitivity analysis of the proposed wet deposition procedure is implemented. The result indicates the applicability of RANS for high-resolution grids considering the effect of terrains on the wet deposition.

• The Journal of Information Systems
• /
• v.25 no.3
• /
• pp.147-173
• /
• 2016

Purpose The purpose of this study was to investigate the relationship between the 6th industrial entrepreneurship and business performances on social capital. The 6th industry based on its social capital can have a significant impact on business performances. Design/Methodology/Approach For this reason, we examined the relationship between entrepreneurship and business performance using the moderator variables of social capital and the Sixth industry certification. As a result, the 6th industrial entrepreneurship affects significant positive business performance. In particular, the authenticity, communication skills, social responsibility, collaborative, risk susceptibility, and challenging mind have a positive effect on business performances. As a result of moderation effect analysis, the 6th industry certification has no interaction effect of entrepreneurship, and only challenging mind and communication skills, the authenticity showed that the positive effect on business performances. Findings Social capital has interaction effects on the 6th industry entrepreneurship. Low level of social capital improves business performance through a strong challenging mind and social responsibility. High level of social capital are more demanding authenticity, collaboration, and risk sensitivity. And the higher level of social capital, the lower the communication ability, electrical conductivity, and social responsibility.

• IE interfaces
• /
• v.25 no.2
• /
• pp.255-263
• /
• 2012

In order to ensure the reliability and specialty of weapon system test results, a policy of extending certified testing service institutions has been driven by applying accreditation system of the ones in defense industry. Bass and Logistic models are used to apply the policy effectively and forecast the diffusion pattern of certified testing service institutions. The parameters for diffusion forecast are estimated using the diffusion pattern of certified testing service institutions in non-defense industry, and these are applied to forecast the diffusion of certified ones in defense industry. Coefficients of innovation and imitation of Bass model are analyzed to derive the factors influencing the early adoption and diffusion patterns. The more increasing the coefficients, the earlier adoption occurred. Diffusion pattern due to coefficient of imitation, internal factor, has larger effect on sensitivity of diffusion pattern. This means that the self recognition of necessity is more effectively worked than the policy or regulations driven by government.

• Journal of Sensor Science and Technology
• /
• v.33 no.2
• /
• pp.93-97
• /
• 2024

With the development of promising future mobility and urban air mobility (UAM) technologies, the demand for LIDAR sensors has increased. The SWIR photodetector is a sensor that detects lasers for the 3D mapping of lidar sensor and is the most important technology of LIDAR sensor. An SWIR photodetector based on QDs in an eye-safe wavelength band of over 1400 nm has been reported. QDs-based SWIR photodetectors can be synthesized and processed through a solution process and have the advantages of low cost and simple processing. However, the organic ligands of QDs have insulating properties that limit their ability to improve the sensitivity and stability of photodetectors. Therefore, the technology to replace organic ligands with inorganic ligands must be developed. In this study, the organic ligand of the synthesized PbS QDs was replaced with a MAPI inorganic ligand, and an SWIR photodetector was fabricated. The analysis of the characteristics of the manufactured photodetector confirmed that the photodetector based on MAPI-capped PbS QDs exhibited up to 26.5% higher responsivity than that based on organic ligand PbS QDs.

• The Journal of the Korea Contents Association
• /
• v.13 no.12
• /
• pp.945-956
• /
• 2013

The character industry is a high value-added industry, and is one of the strategic industries to be fostered. However, the character industry is struggling due to the lack of national consensus on the importance and value of the character industry. Therefore, in order to resolve this issue, the study used the character Input-Output Table of year 2009 of korea to analyze how much the character industry(Toys and games, Models and decorations) contributes to the national economy by measuring economic spreading effects of character industry on national economy. The results shows that character industry shows that production inducement coefficient is column 1.602, row 1.007, index of the sensitivity of dispersion is 0.543, Index of the power of dispersion is 0.864, value-added coefficient is 0.620, income inducement coefficient is 0.334, tax inducement coefficient is 0.066, employment inducement coefficient is 0.008.

• Journal of Industrial Technology
• /
• v.28 no.A
• /
• pp.149-153
• /
• 2008

$C_p$ and other process capability indices are used extensively in industry, However, They are inadequate and widely misused. In a practical application, process average ${\mu}$ is almost always drifted by various assignable causes in process. And control charts will not detect these shifts in process average. In this study, incorporating these undetected shifts, a new capability analysis method is introduced.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.571-576
• /
• 2001

Hydroforming, the new production technology, has been used to manufacture many parts of vehicle in the recent auto industry. When Hydroforming is applied, it is possible to make parts simplification and flexible alteration of section shape in many advantages such as weight reduction, number of parts reduction or performance improvement. This research into shape optimization which reduces number of parts and weight maintaining performance was achieved. In this paper, the COWL CROSS BAA and MT'g BAKT parts of A car STEERING support SYSTEM was introduced by using Hydroforming.

• 중국학논총
• /
• no.69
• /
• pp.167-186
• /
• 2021

在本研究中, 爲了分析自加入WTO以来中國金融業的生産誘導效應, 我們使用2007年, 2012年和2017年的中國投入産出表分析了与其他行業交换了哪些政策影響。主要分析結果如下。首先, 影響力系數而言, 在2007年和2012年, 對中國經濟發展産生影響的傳統制造業正逐渐向具備技術的專業裝備制造業轉移。分析表明, 由于出现冲突迹象, 中國金融業的發展已通過實施擴大内需的政策影響了中國的内需相關行業。其次, 感應度系數, 2007年是2006年加入WTO的五年。由于所有部門的全面開放, 對外貿易總额平均每年增長30％。結果, 認爲金融業已經受到金融業的影響, 幷受到其影響, 從而形成了良性循环。在2012年和2017年获得的結果相似, 在全球金融危机之后, 中國政府与基础設施的建設和重建有關, 例如《中國制造2025》和"一带一路", 以及中部地區, 東北振興和西部等區域均衡發展的政策。分析表明該行業已經影響了金融業。

• Journal of the Korean Statistical Society
• /
• v.5 no.2
• /
• pp.101-107
• /
• 1976

One of the important properties of a 'good' response surface design is that the design should be insensitive to wild observations. In this note, a measure of sensitivity to wild observations is studied. It is shown that designs are made robust to wild observations by making $Tr[X'X)^{-1}M]$ small where M is a moment matrix over some region of interest. The proposed criterion is compared with that suggested by Box and Draper. Some about robust two-variable response surface designs are given.