• Current Photovoltaic Research
• /
• v.5 no.4
• /
• pp.135-139
• /
• 2017

We fabricated two different transparent conducting oxide thin films of ZnO doped with Ga ($Ga_2O_3$ 0.9 wt%) as well as Al ($Al_2O_3$ 2.1 wt%) (GAZO) and ZnO doped only with Al ($Al_2O_3$ 3 wt%) (AZO). It was investigated how it affects the moisture resistance of the transparent electrode. In addition, $Cu(In,Ga)Se_2$ thin film solar cells with two transparent oxides as front electrodes were fabricated, and the correlation between humidity resistance of transparent electrodes and device performance of solar cells was examined. When both transparent electrodes were exposed to high temperature distilled water, they showed a rapid increase in sheet resistance and a decrease in the fill factor of the solar cell. However, AZO showed a drastic decrease in efficiency at the beginning of exposure, while GAZO showed that the deterioration of efficiency occurred over a long period of time and that the long term moisture resistance of GAZO was better.

• Korean Journal of Materials Research
• /
• v.15 no.3
• /
• pp.161-165
• /
• 2005

We investigated selective dry etching of GaAs over AlGaAs and InGaP in high density planar inductively coupled $BCl_3/SF_6$ plasmas. The process parameters were ICP source power (0-500 W), RE chuck power (0-30W) and gas composition $(60-100\%\;BCl_3\;in\;BCl_3/SF_6)$. The process results were characterized in terms of etch rate, selectivities of GaAs over AlGaAs and InGaP, surface morphology, surface roughness and residues after etching. $BCl_3/SF_6$ selective etching of GaAs showed quite good results in this study. Selectivities of GaAs $(GaAs:AlGaAs\~36:1,\;GaAs:InGaP\~45:1)$ were superior at $18BCl_3/2SF_6$, 20 W RF chuck power, 300 W ICP source power and 7.5 mTorr. Addition of $(5-15\%)SF_6\;to\;BCl_3$ produced relatively high selectivities of GaAs over AlGaAs and InGaP during etching due to decrease of etch rates of AlGaAs and InGaP (boiling points of etch products: $AlF_3\~1300^{\circ}C,\;InF_3>1200^{\circ}C$ at atmosphere) at the condition. SEM and AFM data showed slightly sloped sidewall and somewhat rough surface$(RMS\~9nm)$. XPS study on the surface of processed GaAs proved a very clean surface after dry etching. It shows that planar inductively coupled $BCl_3/SF_6$ plasmas could be a good candidate for selective dry etching of GaAs over AlGaAs and InGaP.

• Korean Journal of Optics and Photonics
• /
• v.7 no.3
• /
• pp.287-294
• /
• 1996

An optical phase modulator is fabricated in GaAs/AlGaAs doble heterostructure wafer grown by MOCVD. A self-aligned process, in which the same photoresist pattern is used for both the waveguide etching and the insulation layer formation, is developed and is found to be very useful, Fabry-Perot interference technique is applied to the measurement and the phase modulation efficiency is measured to be 22.5$^{\circ}$/Vmm at 1.31 ${\mu}{\textrm}{m}$ for TE polarization.

• Journal of the Korean Vacuum Society
• /
• v.8 no.3B
• /
• pp.308-314
• /
• 1999

We used the photoreflectance spectroscopy for characterization of the infrared photodetector structure we GaAs/$Al_{0.3}Ga_{0.7}As$ multi-quantum well (MQW) structures grown by molecular beam epitaxy (MBE) method. Energy gap related transitions in GaAS and AlGaAs were observed. The Al composition(x) was determined b Sek's composition formula. MQW related transition energies were identify the transitions, the experimentally observed energies were compare with results of the envelope function approximation for a rectangular quantum well.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.3
• /
• pp.118-123
• /
• 1995

We have successfully fabricated a super low noise pseudomorphic HEMT(PHEMT) device with AlGaAs/InGaAs/GaAs sturcture by using improved T-Gate which have increased a large gaet cross-sectional area about two times in comparision with those of conventional T-gate processes. The PHEMSTs with 0.15$\mu$m-long and 140$\mu$m-wide gates have eshibited a super low noise characteristics, the noise figure of 0.45dB with associated gain of 10.87dB at 12GHz. The cut-off rewuqncy of the device is 94gHz with a transconductance of 418mS/mm.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.13-16
• /
• 2000

A quantum-wire field effect transistor(QW-FET) using asymmetric double InGaAs channel and Si-delta doped barrier has been fabricated. It exhibited good modulation and saturation characteristic in the range of ${\mu}\textrm{A}$ current level. For estimated channel width of 150nm QW-FET, maximum transconductance was about 400 mS/mm which is higher than a conventional heterostructure FET(HFET) with the same epi-structure.

• Proceedings of the Optical Society of Korea Conference
• /
• 1995.06a
• /
• pp.127-137
• /
• 1995

Anomalously large real space charge transfer through thick barries in GaAs asymmetric double quantum wells is studied by photoluminesence exitation. This inter-well excitonic transfer is very large when the barrier is the Al0.3Ga0.7As alloy, but disappears when the barrier is GaAs/AlAs digital alloy with an equivalent Al concentration of 0.28. These resilts combined with observed x and barrier thickness depence suggest that the spatial fluctuation of the atomic arrangment of Ga and Al in the alloy may be responsible for this transfer. This picture is supported by the quantum mechanical calculation in three dimensions which takes into account the side fluctuation effects.

• Journal of the Korean Vacuum Society
• /
• v.15 no.2
• /
• pp.201-208
• /
• 2006

Optical characteristics of InGaAs quantum dot (QD) laser structures with an Al native oxide (AlOx) layer as a current-blocking layer were studied by means of photoluminescence (PL), PL excitation, and spatially-resolved micro-PL techniques. The InGaAs QD samples were first grown by molecular-beam epitaxy (MBE), and then prepared by wet oxidation and thermal annealing techniques. For the InGaAs QD structures treated by the wet oxidation and thermal annealing processes, a broad PL emission due to the intermixing effect of the AlOx layer was observed at PL emission energy higher than that of the non-intermixed region. We observed a dominant InGaAs QD emission at about 1.1 eV in the non-oxide AlAs region, while InGaAs QD-related emissions at about 1.16 eV and $1.18{\sim}1.20eV$ were observed for the AlOx and the SiNx regions, respectively. We conclude that the intermixing effect of the InGaAs QD region under an AlOx layer is stronger than that of the InGaAs QD region under a non-oxided AlAs layer.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.1
• /
• pp.30-36
• /
• 2001

0.35 ${\mu}{\textrm}{m}$-gate AlGaAs/InGaAs PHEMTs have been fabricated using electron beam lithography. DC and AC characteristics of PHEMTs having different gate widths and number of fingers were measured at various bias conditions. An MIMIC power amplifier operating at 35 GHz has been designed and fabricated using passive element library. The power amplifier showed gain and input reflection coefficient of 7.9 ㏈ and -15 ㏈, respectively, at 27.6 GHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.9
• /
• pp.19-24
• /
• 2004

In this paper, we have demonstrated the fabrication of a 70 nm foot print of the T-gate by using a positive resist ZEP520/P(MMA-MAA)/PMMA trilayer by double exposure method without a thin dielectric supporting layer on the substrate. The device performance was characterized by DC and RF measurement. The fabricated 70 nm InGaAs/InAlAs MHEMTS with 70 ${\mu}{\textrm}{m}$ unit gate width and 2 fingers showed good DC and RF characteristics of Idss, max =228.6 mA/mm, gm =645 mS/mm, and fT =255 GHz, respectively.