• Transactions on Electrical and Electronic Materials
• /
• 제11권2호
• /
• pp.77-80
• /
• 2010

Indium tin oxide (ITO) films with a 5 nm thick Au interlayer were prepared on glass substrates. The effects of the Au interlayer on the gas sensitivity for detecting methanol vapors were investigated at room temperature. The conductivity of the film sensor increased upon exposure to methanol vapor and the sensitivity also increased proportionally with the methanol vapor concentration. In terms of the sensitivity measurements, the ITO film sensor with an Au interlayer shows a higher sensitivity than that of the conventional ITO film sensor. This approach is promising in gaining improvement in the performance of ITO gas sensors used for the detection of methanol vapor at room temperature.

• 한국재료학회지
• /
• 제17권4호
• /
• pp.232-235
• /
• 2007

Indium tin oxide (ITO) films were deposited on polycarbonate CR39 substrate using DC magnetron sputtering. ITO thin films were deposited at room temperature because glass-transition temperature of CR39 substrate is $130^{circ}C$ ITO thin films are used as bottom and top electrodes and for organic thin film transparent transistor (OTFT). The electrodes electrical properties of ITO thin films and their optical transparency properties in the visible wavelength range (300-800 nm) strongly depend on the volume of oxygen percent. The optimum resistivity and transparency of ITO thin film electrode was achieved with a 75 W plasma power, 10 % volume of oxygen and a 27 nm/min deposition rate. Above 85% transparency in the visible wavelength range (300-800 nm) was measured without post annealing process, and resistivity as low as $9.83{\times}^{TM}10^{-4}{\Omega}$ cm was measured at thickness of 300 nm.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권7호
• /
• pp.700-705
• /
• 1997

Transparent conducting indium tin oxide (TC-ITO) thin films are deposited on soda lime glass by a dc magnetron sputtering technique having the unbalanced-magnet structure in order to improve the electrical/material characteristics and to avoid the surface damages. The material properties are measured by the x-ray diffractometer (XRD) and atomic force microscope (AFM). The (400) peak as the preferred orientation of <100> direction for ITO thin films is stabilized with the increase of substrate temperature. The surface roughness estimated by AFM 3D image at the substrate temperature of 40$0^{\circ}C$ is extremely uniform. The best resistivity of ITO films (5500 $\AA$ thick) at 40$0^{\circ}C$ is about 1.3$\times$10$^{-4}$ $\Omega$cm on the position of 4 cm from substrate center.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1992년도 춘계학술대회 논문집
• /
• pp.114-116
• /
• 1992

ITO/TiO$_2$/Se solar cell were fabricated by vacuum deposition method, the Se and TiO$_2$were deposited on the ITO/Glass. Prior to the electrical properties of film, the provide Te between the ITO and the Se film were deposited by substrate temperature 20[$^{\circ}C$] and evaporation time 15[min], next time TiO$_2$ were treated by rf-magnetron sputtering in substrate temperature 250[$^{\circ}C$]. Fabricated ITO/TiO$_2$/Se solar cell were as follows : Open Voltage V$\_$oc/=848[mV], Short Circuit Current I$\_$sc/=10.79[mA/$\textrm{cm}^2$]. Fill Factor FF=0.518, energy conversion efficiency η=4.74[%] under the illumination of AM 1.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.1042-1045
• /
• 2004

ITO thin films ($\sim150nm$) are deposited on glass substrates by different deposition condition. The sheet resistance of ITO thin films measured by using a four probe station. The microstructure of these films is determined using a X-ray diffractometer (XRD) and a scanning electron microscope (SEM) and a atomic force microscope (AEM). The sheet resistance of ITO thin films compared $s_11$ values by using a near field scanning microwave microscope.

• Transactions on Electrical and Electronic Materials
• /
• 제4권2호
• /
• pp.10-14
• /
• 2003

Flexible displays such as plastic-based liquid crystal displays (LCDs) and organic light-emitting diode displays (OLEDDs) have been researched and developed at KETI since 1997. The plastic film substrate is very weak to heat and pressure compared to glass substrate, that its fabrication process is limited to 110$^{\circ}C$ and low pressure. The ITO films were deposited on the bare plastic film substrate by rf-magnetron sputtering. Moreover, in order to maintain uniform cell gap and pressure on the plastic film substrate, we utilized newly-invented jig and fabrication process. Electro-optical characteristics were better than or equivalent to those of typical glass LCDs though it is thinner, lighter-weight, and more robust than glass LCDs.

• 한국안광학회지
• /
• 제7권2호
• /
• pp.163-167
• /
• 2002

$Ni(OH)_2/Ni$ Glass 박막에서 전기변색 속도 개선에 대한 연구를 수행하였다. 이는 선글라스의 변색속도가 수분 이상 소요되는 단점을 해결하고자 e-beam evaporator를 이용하여 니켈 금속 박막을 증착시킨 후, 전기화학적 산화-환원 반응으로 $Ni(OH)_2$에 대한 전기변색 특성을 연구하였다. 전기전도성을 갖는 ITO 에서보다 Glass 위에서의 $Ni(OH)_2$의 변색 속도가 오히려 빠르다. 이는 전위와 투과율을 측정함으로서 알 수 있다. XPS를 이용하여 Glass와 $Ni(OH)_2$ 사이의 초박막(${\sim}10{\AA}$) Ni 금속의 존재를 확인하였고, 이 나노 박막은 전기변색 장치의 응답 속도에 영향을 마쳤다. 기존의 선글라스가 5분 정도 소요되는 반면 니켈 나노 박막을 이용한 변색소자에서는 1~2초 정도 소요된다. 이론적으로는 수 ms 이내이지만 전기적 저항으로 인해 초 단위의 응답속도를 보이고 있다.

• 한국정밀공학회지
• /
• 제21권12호
• /
• pp.92-99
• /
• 2004

The formation degree of sustain (ITO pattern) decides quality of PDP (Plasma Display Panel). For this reason, it makes efforts in searching defects more than 30 un as 100%. Now, the existing inspection is dependent upon naked eye or microscope in off-line PDP manufacturing process. In this study developed prototype inspection system of PDP 170 glass is based on line-scan mechanism. Developed system creates information that detects and sorts kinds of defect automatically. Designed inspection technology adopts multi-vision method by slip-beam formation for the minimum of inspection time and detection algorithm is embodied in detection ability of developed system. Designed algorithm had to make good use of kernel matrix that draws up an approach to geometry. A characteristic of defects, as pin hole, substance, protrusion, are extracted from blob analysis method. Defects, as open, short, spots and et al, are distinguished by line type inspection algorithm. In experiment, we could have ensured ability of inspection that can be detected with reliability of up to 95% in about 60 seconds.

• International Journal of Precision Engineering and Manufacturing
• /
• 제7권3호
• /
• pp.18-23
• /
• 2006

The formation degree of sustain (ITO pattern) determines the quality of a PDP (Plasma Display Panel). Thus, in the present study, we attempt to detect 100% of the defects that are larger than $30{\mu}m$. Currently, the inspection method in the PDP manufacturing process is dependent upon the naked eye or a microscope in off-line mode. In this study, a prototype inspection system for PDP ITO patterned glass is developed. The developed system, which is based on a line-scan mechanism, obtains information on the defects and sorts the defects by type automatically. The developed inspection system adopts a multi-vision method using slit-beam formation for minimum inspection time and the detection algorithm is embodied in the detection ability. Characteristic defects such as pin holes, substances, and protrusions are extracted using the blob analysis method. Defects such as open, short, spots and others are distinguished by the line type inspection algorithm. It was experimentally verified that the developed inspection system can detect defects with reliability of up to 95% in about 60 seconds for the 42-inch PDP panel.

• 한국전기전자재료학회논문지
• /
• 제19권11호
• /
• pp.1044-1049
• /
• 2006

We reported on characteristics of the fluorescent OLED fabricated on commercial ITO/glass and BCS grown IZO/glass substrate, respectively. The amorphous IZO anode film grown by box cathode sputtering(BCS) exhibited similar electrical and optical characteristics to commercial ITO anode even though it was deposited at room temperature. In addition, the amorphous IZO anode showed higher workfunction (5.2 eV) than that of the commercial ITO anode (5.0 eV) after ozone treatment for 10 min. Furthermore, fluorescent OLED fabricated on amorphous IZO anode film showed improved current-voltage-luminance characteristics, external quantum efficiency and power efficiency en contrast with fluorescent OLED fabricated on commercial ITO anode film. It was thought that smooth surface and high workfunction of amorphous IZO anode lead to more efficient hole injection by reduction of interface barrier height between anode and organic layers.