• 한국세라믹학회지
• /
• 제38권11호
• /
• pp.973-979
• /
• 2001

Sn을 도핑한 In$_2$O$_3$(ITO) 박막을 R.F. 마그네트론 반응성 스퍼터링법에 의해서 증착하였다. 동일한 마그네트론 스퍼터링 조건에서 증착위치에 따른 ITO 박막의 저항, 자유 전하 농도 및 이동도 전기적 특성을 조사하였다. 동일한 마그네트론 스퍼터링 조건임에도 불구하고, ITO 박막의 전기적 특성은 증착위치에 따라 불균질성을 나타내었다. 타겟의 중심에 위치한 기판위에 증착된 ITO 박막의 저항은 최소 값인 2~4$\times$$10^{-4}$ $\Omega$.cm인 반면, 중심에서 멀어질수록 박막의 전기 저항은 대칭적으로 증가하였다. ITO 박막의 밀도 측정 결과도 중심에서 이론 밀도 값의 97%에 해당하는 7.0g/$cm^3$를 나타내나, 위치가 중심에서 멀어질수록 박막의 밀도가 대칭적으로 감소하였다. ITO 박막에서 이동도와 전도도는 밀도에 직접적으로 영향을 받는 것이 실험적으로 확인되었다. ITO 박막의 밀도가 7.0g/$cm^3$(이론 밀도의 97%)인 경우, 자유행정거리와 입자크기(=주상의 직경)가 동일한 값을 가지나, 밀도가 이 보다 감소하면 자유행정거리와 입자크기의 차이는 더욱 증가하였다. 이 결과는 ITO 박막의 밀도가 7.0g/$cm^3$인 경우는 입계가 자유 전자의 전도에 중요한 산란 원으로 작용하는 반면, 그 외의 경우는 결정 내의 공격자점, 공공, 기공 등이 다른 산란 원으로 작용하고 있다는 것을 나타낸다.

• Journal of the Optical Society of Korea
• /
• 제13권1호
• /
• pp.65-74
• /
• 2009

Device quality indium tin oxide (ITO) films are deposited on glass substrates and ultra-thin diamond-like carbon films are deposited as a buffer layer on ITO by a pulsed Nd:YAG laser at 355 nm and 532 nm wavelength. ITO films deposited at room temperature are largely amorphous although their optical transmittances in the visible range are > 90%. The resistivity of their amorphous ITO films is too high to enable an efficient organic light-emitting device (OLED), in contrast to that deposited by a KrF laser. Substrate heating at $200^{\circ}C$ with laser wavelength of 355 nm, the ITO film resistivity decreases by almost an order of magnitude to $2{\times}10^{-4}\;{\Omega}\;cm$ while its optical transmittance is maintained at > 90%. The thermally induced crystallization of ITO has a preferred <111> directional orientation texture which largely accounts for the lowering of film resistivity. The background gas and deposition distance, that between the ITO target and the glass substrate, influence the thin-film microstructures. The optical and electrical properties are compared to published results using other nanosecond lasers and other fluence, as well as the use of ultra fast lasers. Molecularly doped, single-layer OLEDs of ITO/(PVK+TPD+$Alq_3$)/Al which are fabricated using pulsed-laser deposited ITO samples are compared to those fabricated using the commercial ITO. Effects such as surface texture and roughness of ITO and the insertion of DLC as a buffer layer into ITO/DLC/(PVK+TPD+$Alq_3$)/Al devices are investigated. The effects of DLC-on-ITO on OLED improvement such as better turn-on voltage and brightness are explained by a possible reduction of energy barrier to the hole injection from ITO into the light-emitting layer.

• 한국표면공학회지
• /
• 제41권5호
• /
• pp.214-219
• /
• 2008

Indium tin oxide (ITO) films were deposited on PET substrate by RF superimposed DC magnetron sputtering using ITO (doped with 10 wt% $SnO_2$) target. Substrate temperature was maintained below $750^{\circ}C$ without intentionally substrate heating during the deposition. The discharge voltage of DC power supply was decreased from 280 V to 100 V when superimposed RF power was increased from 0 W to 150 W. The electrical properties of the ITO films were improved with increasing of superimposed RF power. In the result of cyclic bending test, relatively high mechanical property was obtained for the ITO film deposited with RF power of 75 W under DC current of 0.75 A which could be attributed to the decrease of internal stress caused by decrease in both deposition rate and plasma impedance.

• 한국재료학회지
• /
• 제19권9호
• /
• pp.499-503
• /
• 2009

Transparent ITO films were deposited on a polycarbonate substrate with RF magnetron sputtering in a pure argon (Ar) and oxygen ($O_2$) gas atmosphere, and then post deposition electro annealed for 20 minutes in a $4{\times}10^{-1}$ Pa vacuum. Electron bombardment with an accelerating voltage of 100 V increased the substrate temperature to $120^{\circ}C$. XRD analysis of the deposited ITO films did not show any diffraction peaks, while electro annealed films indicated the growth of crystallites on the (211), (222), and (400) planes. The sheet resistance of ITO films decreased from 103 to $82{\Omega}/\square$. The optical transmittance of ITO films in the visible wavelength region increased from 85 to 87%. Observation of the work function demonstrated that the electro-annealing increased the work function of ITO films from 4.4 to 4.6 eV. The electro annealed films demonstrated a larger figure of merit of $3.0{\times}10^{-3}{\Omega}^{-1}$ than that of as deposited films. Therefore, the electro annealed films had better optoelectrical performances than as deposited ITO films.

• 한국표면공학회지
• /
• 제38권2호
• /
• pp.69-72
• /
• 2005

ITO-Al-ITO multi-layers were deposited at room temperature by RF magnetron sputtering on polyethylene terephthalate (PET). The films were deposited at various pressures of $8\times10^{-4},\;1\times10^{-3},\;4\times10^{-3},\;8\times10^{-3}\;and\;1\times10^{-2}$ Torr. A correlation between microstructure and electro-optical properties was studied. Films deposited? at low pressure have higher transmission, and lower reflectance and resistance than film deposited at high pressure. Sheet resistance, transmission, and reflectance were $141.6\Omega/\Box\;88\%\;and\;6.8\%$ resectively when the deposition pressure was $8\times10^{-4}$ torr, that was the optimum condition.

• 반도체디스플레이기술학회지
• /
• 제7권2호
• /
• pp.59-62
• /
• 2008

The Lifetime of OLEDs by ITO/glass substrates cleaning method and cathode deposition method were investigated in the fabrication of green light emitting OLEDs with $Alq_3$-C545T fluorescent system. In our experiments, the optimum cleaning method was obtained at last processing of boiling IPA(isopropyl alcohol). And the optimum deposition methode was obtained at 3 steps deposition rate of Al. The deposition rate of 3 steps progressed changing from $0.5\AA$/sec to $3\AA$/ sec. The green light emitting OLED with plasma treatment at 150W for 2 minutes showed the highest luminance and efficiency of 20000 cd/$m^2$ and 16 lm/W. On the contrary, the OLED device without plasma treatment showed much lower performance with the luminance and efficiency of 3500 cd/$m^2$ and 2 lm/W.

• 한국재료학회지
• /
• 제21권5호
• /
• pp.255-262
• /
• 2011

This paper has relatively high technical standard and experimental skill. The fabrication of TCO film with high transparency, low resistance and low chromaticity require exact control of several competing factors. This paper has resolved these problems reasonably well, thus recommended for publication. Indium tin oxide(ITO) thin films were by D.C. magnetron roll-to-roll sputter system utilizing ITO and $SiO_2$ targets of ITO and $SiO_2$. In this experiment, the effect of D.C. power, winding speed, and oxygen flow rate on electrical and optical properties of ITO thin films were investigated from the view point of sheet resistance, transmittance, and chromaticity($b^*$). The deposition of $SiO_2$ was performed with RF power of 400W, Ar gas of 50 sccm and the deposition of ITO, DC power of 600W, Ar gas of 50 sccm, $O^2$ gas of 0.2 sccm, and winding speed of 0.56m/min. High quality ITO thin films without $SiO_2$ layer had chromaticity of 2.87, sheet resistivity of 400 ohm/square, and transmittance of 88% and $SiO_2$-doped ITO Thin film with chromaticity of 2.01, sheet resistivity of 709 ohm/square, and transmittance of more than 90% were obtained. As a result, $SiO_2$ was coated on PET before deposition of ITO, their chromaticity($b^*$) and transmittance were better than previous results of ITO films. These results show that coating of $SiO_2$ induced arising chromaticity($b^*$) and transmittance. If the thickness of $SiO_2$ is controlled, sheet resistance value of ITO film will be expected to be better for touch screen. A four point probe and spectrophotometer are used to investigate the properties of ITO thin films.

• 분석과학
• /
• 제6권2호
• /
• pp.239-246
• /
• 1993

ITO coated glass, bare glass, 그리고 (100)Si 기판 위에 증착된 $(BaSr)TiO_3$ 박막의 구조는 기판의 종류에 관계없이 변하지 않았으나 결정성은 다결정 ITO층과 (100)Si 기판에 있어서 증대되었다. ITO coated glass 기판 위에 증착된 $(BaSr)TiO_3$ 박막의 조성은 거의 화학양론적으로 일치하였으며 ((Ba+Sr)/Ti=1.08~1.09) 증착 중 상당히 치밀하고 균질하였다. 그러나 증착온도가 증가함에 따라 성장한 박막과 ITO층 사이에, 그리고 ITO층과 base glass 사이에 확산이 보다 심화되었다. ITO coated glass 기판 위에 증착된 $(BaSr)TiO_3$ 박막은 상당히 투명하였으며(투과율 약 80%) 굴절률($n_f$)은 기판온도의 증가에 따라 2.138~2.286이었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.7-7
• /
• 2010

Indium tin oxide (ITO) - SWNT nano crystalline composites was synthesized at low temperature(${\sim}250^{\circ}C$)using Nano Cluster Deposition technique by Metal Orhoganic Chemical Vapor Deposition method. XRD patterns of ITO- SWNT composite shows pure cubic phases without any secondary phase. I-V measurement gives resistance of 12 ohms for Sn doped (3 wt %) indium oxide-SWNT composites. The electrical conductivity of the nano composites is significantly enhanced compared to the SWNT.

• 한국진공학회지
• /
• 제21권4호
• /
• pp.205-211
• /
• 2012

인듐주석산화막/폴리에틸렌 테레프탈레이트(ITO/PET: indium tin oxide/polyethylene terephthalate) 유연 기판 위에 성장된 산화아연(ZnO) 나노로드(nanorods)를 이용하여 형성된 은(Ag) 입자의 광학적 특성 및 소수성 표면에 대해 조사하였다. 시료를 준비하기 위해 스퍼터링법(sputtering)으로 코팅된 산화아연 씨드층(seed layer)을 이용하여 전기화학증착법(electrochemical deposition)으로 산화아연 나노로드를 성장시킨 후, 열증발증착법(thermal evaporation)을 사용하여 은을 증착하였다. 산화아연 나노로드의 불연속적인 표면 특성 때문에 은이 증착되면서 나노크기를 갖는 입자로 형성되었다. 비교를 위해 같은 조건으로 은을 평평한 ITO/PET에 증착하여 시료를 준비하였으며, 증착되는 은의 양을 조절하기 위해 100초에서 600초까지 열증발증착시간을 변화시켰다. 은 증착시간이 증가할수록 산화아연 나노로드 표면에 형성되는 은 입자의 크기와 양이 증가하였으며, 또한 빛의 흡수율이 가시광 영역에서 크게 증가하는 것을 확인하였다. 이는 은 입자의 국소표면플라즈몬공명(localized surface plasmon resonance)에서 기인된 것으로 짐작한다. 또한 물방울 테스트실험에서 평평한 ITO/PET에 증착된 은에서의 접촉각(contact angle)보다 산화아연 나노로드에 증착된 은 입자에서의 접촉각이 크게 증가함을 보여, 개선된 소수성 표면을 가질 수 있음을 확인하였다. 이러한 광학적 특성과 소수성 표면 결과는 산화아연 나노로드의 기반의 염료감응형 태양전지 또는 자정효과(self-cleaning)를 갖는 표면구조로 유연소자에 유용하게 응용할 수 있을 것으로 기대된다.