• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.11
• /
• pp.1171-1177
• /
• 2013

In this study, the torque transmitting capability of a flexible disk coupling was investigated. Flexible disc coupling is used to transmit power between two axes, and there exist mis-alignments such as angle of deviation and end play between two shafts. A disk is an important part in the flexible disk coupling because the disk has to transmit power between two mis-aligned shafts. To investigate the effect of mis-alignment on load carrying capacity, finite element analyses were carried out. Analyses were carried out for two types of disk; i.e., circular and square disks. The rotational and bending stiffness of disk plates was predicted to investigate the effect of mis-alignment on stress. As a result, it was shown that the mis-alignment can cause severe decrease in load-carrying capacity. And, the square disk showed better performance than the circular disk.

• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.874-877
• /
• 2018

Many SMDs (surface mount device) are mounted and mutually connected on a PCB (printed circuit board). System performance degrades when their transmission characteristics are bad. Pads connecting a PCB and SMDs affects PCB transmission characteristics significantly, so pad should be properly aligned to optimize impedance matching. In this paper, effects on PCB transmission characteristics are simulated by pad alignment. When frequency is relatively low, pad alignment seldom affect PCB transmission characteristics, but it affects more and more when frequency or pad size becomes larger. Therefore, pad alignment should be carefully chosen based on target frequency and pad size. Especially, the proposed edge-aligned pad is generally more advantageous over the conventional centered-aligned pad in 12~16 GHz Ku-band frequency.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.26 no.6
• /
• pp.611-616
• /
• 2008

When extracting geo-referenced 3D data from cameras mounted on Mobile Mapping Systems, one of important properties for accuracy of extracted data is the alignment of the relative translation(lever-arm) and rotation(bore-sight) between the coordinate systems of Inertial Measurement Unit(IMU)/Ground Positioning System(GPS) and cameras. Since the conventional method calculates absolute camera orientation using ground control points (GCP), the alignment is determined in one Coordinated System (GPS Coordinated System). It basically require GCP. We proposed a mathematical model for the alignment using the initially uncoupled data of cameras and IMU/GPS without GCPs.

• Journal of Advanced Navigation Technology
• /
• v.22 no.6
• /
• pp.500-506
• /
• 2018

In this paper, we considered the one-shot alignment using master inertial navigation system (MINS) and slave inertial navigation system (SINS) in the missile to find the exact posture of a missile. In order to perform one-shot alignment, the tilt angle between MINS and SINS must be obtained, which can be compensated by obtaining the tilt angle between missile round and SINS. The tilt angle was calculated by using the roll rotation of missile round, jig for rotating the missile round and interface structure to measure the horizontal state by using a horizontal angle meter were constructed. As a result of the tilt angle save (TAS) inspection, the tilt angle ${\alpha}$, ${\beta}$, ${\gamma}$ is normal range and it is possible to perform one-shot alignment by compensating this value.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.11
• /
• pp.1399-1404
• /
• 2012

Because satellites operate in space, it is impossible to repair them when they malfunction. Therefore, to ensure the normal function of the payload used in the satellites, accurate assembly and installation of parts are crucial. To prevent abnormal functioning in the extreme environments during launch and in space, it is essential to test changes at the parts and system levels by performing alignment measurement before and after the launch environment test and the space environment test. Recently, noncontact three-dimensional precision machinery for medium- and large-sized parts has been developed. One of these is the theodolite measurement system, which is widely used in the aerospace industry. This study measures the angle of the dual thruster module that is used to control the attitude of KOMPSAT by using a theodolite, and alignment measurement and a reliability analysis are performed.

• 제어로봇시스템학회:학술대회논문집
• /
• 1994.10a
• /
• pp.665-671
• /
• 1994

Some extended results in the study of two-position alignment for strapdown inertial navigation system are presented. In [1], an observability analysis for two-position alignment was done by analytic rank test of the stripped observability matrix and numerical calculation of the error covariance propagation using ten-state error model. In this paper, it is done by an analytic approach which utilizes the nonsingular condition of the determinant of simplified stripped observability matrix and by numerical calculation of the error covariance propagation accomplished in more cases than [1], and the twelve-state error model including vertical channel is used instead of ten-state error model. In addition, it is confirmed that this approach more clearly produces the same result as shown in the original work in terms of complete observability and there exist some better two-position configurations than [1] using the twelve-state error model.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.9
• /
• pp.617-625
• /
• 2022

This study investigates the use of movable calibration target for gyroscopic and accelerometer bias compensation of inertial measurement units for firing lane alignment. Calibration source is detected with the help of vision sensor and its information in fused with other sensors on launcher for error correction. An algorithm is proposed and tested in simulation. It has been shown that it is possible to compensate sensor biases in firing launcher in few seconds by accurately estimating the location of calibration target in inertial frame of reference.

• Management & Information Systems Review
• /
• v.6
• /
• pp.45-61
• /
• 2001

Among the changes of the management environments surrounding enterprises, one of the most important reasons that affect the organization management in the future would be the rapid development in the field of information technology(IT). And every company takes the speed to be important to maintain the competitive superiority of its own especially. To meet this kind of circumstances, the expectations to reorganize the business processes using the IT become higher. The IT is worth when the companies manifest their own potential powers by taking advantage of the it and when they evolve and apply the novel ways to the business as well. Even though they, therefore, introduce the information system to realize their strategic superiorities, it is difficult to achieve their initial aims. Moreover, in the phase of IT introduction, it is necessary to include the property of alignment between the IT and the conventional management fields containing the management strategy and the organization planning. In the case the company revolution by IT is carried out, the two facts we should note to maintain the alignment between the management strategy and the target of organization are as follows. First. it is required to share the common and underlying recognition on the IT between the chief executive officers(CEOs) and the system part. Second. it is important to exchange information with other companies by utilizing the IT.

• Journal of KIISE:Software and Applications
• /
• v.32 no.4
• /
• pp.300-311
• /
• 2005

Terms are linguistic realization of technical concepts. Term constituents are important elements used for representing the concept. Since many new terms are created from the modification or combination of existing constituents, it is important to analyze term constituents for understanding the concept of the term. It means that term constituents offer clues for understanding the concept of terms. However, there are a couple of difficulties in matching concept unit and term constituents such as mismatching between a term constituent and a concept unit, homonym of term constituents and synonym of term constituents. To solve them, it is necessary to recognize concept units of term constituents. In this paper, we define an English term constituent as the concept unit and use an alignment algorithm between English-Korean term constituents in order to recognize concept units of term constituents. By our alignment algorithm we recognize Korean term constituents corresponding to an English term constituent with about $93\%$ precision.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.21 no.4
• /
• pp.293-299
• /
• 2003

In the future, the design of road should be convenient in using of high-technology information and it needs the design of alignment that is able to make the maximum vehicles inducement function appropriated for CNS(Car Navigation System). So it needs to analysis appropriately the alignment of road for the improvement design of road which is established and to make the design of road and the coordinate of the main points. Therefore, this research had acquired the road data by RTK-GPS to accurate the analysis of road alignment and compared with Total Station. As the result, we could acquire the design source of the road alignment using RTK-GPS. Also, it was estimated the accuracy after comparing the design with RTK-GPS coordinates. We made an analysis of the degree of slant or the ups and downs of surface. We made an analysis of three dimensional visual information which was included in GSIS concept and estimated the accuracy. Finally, we analyzed the earth volume calculation by comparing with Total Station.