• 한국전기전자재료학회논문지
• /
• 제14권2호
• /
• pp.158-162
• /
• 2001

In this report, a new process for patterning of YBaCuO thin films, ICP(inductively coupled plasma) method, is described by comparing with existing wet etching method. Two 100㎛ wide and 2mm long YBaCuO striplines on LaAlO$_3$ substrates have been fabricated using two patterning techniques. And the properties were compared with the critical temperature and the SEM photography. Then, the critical temperatures of two samples were about 88 K, but the cross section of sample using ICP method was shaper than that using the wet etching method. ICP method can be used as a good etching technique process for patterning of YBaCuO superconductor.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.608-611
• /
• 2000

Large area plasma source becomes important as the substrate size increases. In this work, four inductively coupled plasma(ICP) unit sources are distributed 2${\times}$2 array. E-ICP concept is applied to the 2${\times}$2 array ICP and its effect is examined. Characteristics of the plasma are measured, and photoresist etching is performed with oxygen plasma. Good etching characteristic in terms of etching rate and uniformity can be obtained with E-ICP.

• 한국산학기술학회논문지
• /
• 제5권2호
• /
• pp.128-131
• /
• 2004

본 연구에서는 STS-ICP ASEHR을 이용하여 Etch와 Deposition 공정을 반복하여 에칭을 하는 Bosch 식각에 관하여 연구하였다. 기본적인 Etch rate의 변화는 Etching하고자 하는 Wafer에 Deposition된 PR 또는 SiO₂의 두께와 Etching하고자 하는 Wafer의 Depth 및 Pattern size가 영향을 준다. 그러나 이러한 기본적인 변수 외에 STS-ICP ASEHR 장비의 Platen power, Coil power 및 Process pressure에 다양한 변화를 주어 각 변수에 따른 Etch rate을 관찰하였다. 각 공정별 변수를 준 결과 Platen power 12W, Coil power 500W, Etch/Passivation Cycle 6/7sec 일 경우 Etch rate은 1.2㎛/min 이었고, Sidewall prpfile은 90±0.2˚로 나타나 매우 우수한 결과를 보였다. 이는 ICP를 이용한 Bosch Process에 의한 결과임을 확인할 수 있었다.

• 마이크로전자및패키징학회지
• /
• 제9권4호
• /
• pp.11-16
• /
• 2002

본 연구에서는 $SrBi_2Ta_2O_9$ (SBT)박막의 고속식각에 따른 잔류물질 및 식각 손상의 영향을 조사하였다. ICP-RIE (inductively coupled plasma reactive ion etching) 의 ICP power와 CCP(capacitively coupled plasma) power를 변화시키면서 고속식각에 따른 박막의 손상과 열화를 XPS 분석과 Capacitance-Voltage (C-V) 측정을 통하여 알아보았다. ICP와 CCP의 power가 증가함에 따라 식각율이 증가하였고 ICP power가 700 W, CCP power가 200 W 일때 식각율은 900$\AA$/min이었다. 강유전체의 건식식각에 있어서 문제점이 플라즈마에 의한 강유전체 박막의 열화인데 반응가스 $Ar/C1_2/CHF_3$를 20/14/2의 비율로 사용하고 ICP와 CCP power를 각각 700w와 200w로 사용하였을 때 전혀 열화되지 않는 강유전체 박막의 특성을 얻을 수 있었다. 본 연구 결과는 Metal-Ferroelectric-Semiconductor (MFS) 또는 Metal-Ferroelectric-Insulator-Semiconductor (MFIS) 구조를 가지는 단일 트랜지스터형 강유전체 메모리 소자를 만드는데 건식 식각이 응용될 수 있음을 보여준다

• 한국전기전자재료학회논문지
• /
• 제17권7호
• /
• pp.782-787
• /
• 2004

Superconducting flux flow transistor (SFFT) is based on a control of the Abrikosov vortex flowing along a channel. The induced voltage by moving of the Abrikosov vortex in an SFFT is greatly affected by the thickness, the width, and the length of channel. In order to fabricate a reproducible channel in the SFFT, we studied the variation of the critical characteristics of ${YBa}_2{Cu}_3{O}_7-\delta(YBCO)$ thin films with the etching time using ICP (Inductively coupled plasma) system. From the simulation, it was certified that the vortex velocity was increased in a low pinning energy at channel width 0,5 mm. The surfaces of YBCO thin film were etched by ICP etching system. We observed the etched channel surfaces by AFM (Atomic Force Microscope) and measured the critical current density with etching time. As a measured results, the etching thickness of channel should be optimized to fabricated a flux flow transistor with specified characteristics.

• 센서학회지
• /
• 제16권2호
• /
• pp.126-131
• /
• 2007

In this paper, we fabricated piezoresistive pressure sensor with dry etching technology which used ICP-RIE (inductively coupled plasma reactive ion etching) and etching delay technology which used SOI (silicon-on-insulator). Structure of the fabricated pressure sensor shows a square diaphragm connected to a frame which was vertically fabricated by dry etching process and a single-element four-terminal gauge arranged at diaphragm edge. Sensitivity of the fabricated sensor was about 3.5 mV/V kPa at 1 kPa full-scale. Measurable resolution of the sensor was not exceeding 20 Pa. The nonlinearity of the fabricated pressure sensor was less than 0.5 %F.S.O. at 1 kPa full-scale.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.612-615
• /
• 2000

The etch rate of $SiO_2$ in Enhanced - Inductive Coupled Plasma (E-ICP) and CW-ICP systems are investigated. As addition of $O_2$ to $CF_4$ gas increases oxide etch rate, E-ICP etching shows the highest etch rate (about 6000A) at an optimized condition with 30% $O_2$ in $CF_4$ 70Hz at the modulation frequency of 70Hz. E-ICP also shows better etch profile than CW-ICP.

• Corrosion Science and Technology
• /
• 제2권5호
• /
• pp.238-242
• /
• 2003

The characteristics of Ru etching using $O_2/Cl_2$ plasmas were investigated by employing inductively coupled plasma (ICP) etcher. The changes of Ru etch rate, Ru to $SiO_2$ etch selectivity and Ru electrode etching slope with the gas flow ratio, bias power, total gas flow rate, and source power were scrutinized. A high etching slope (${\sim}86^{\circ}$) and a smooth surface after etching was attained using $O_2/Cl_2$ inductively coupled plasma.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.259-262
• /
• 2003

Superconducting flux flow transistor(SFFT) is based on a control of the Abrikosov vortex flowing along a channel. The induced voltage by moving of the Abrikosov vortex in SFFT is greatly affected by the thickness and width, of channel. In order to fabricate a reproducibility channel in SFFT, we have researched the variation of the critical characteristics of YBCO thin films with the etching time using ICP(Inductively coupled plasma) system. It was certified that the velocity of vortex decreased with increasing the width of channel and was saturated faster in low bias from a simulation. An etching mechanism of YBCO thin films by ICP system was also certified by AFM(Atomic Force Microscope) and by measuring the critical current density with etching time. As measurement result, we could analyze that we should optimize the etching thickness of channel part to construct a flux flow transistor with desired characteristics.

• 전력전자학회논문지
• /
• 제15권4호
• /
• pp.274-281
• /
• 2010

본 논문에서는 반도체 플라즈마 식각 시스템의 균일도 향상을 위한 CCP와 ICP 결합 임피던스정합 장치를 제안한다. 이중주파수 전원공급 장치는 CCP와 ICP로 구성되어 있고 첫 번째 구성은 고집적화를 위해 페라이트 코어를 사용한 유도 결합 플라즈마(ICP : Inductively Coupled Plasma)방식이며, 두 번째 구성은 셀 전체의 균일도 향상을 위한 용량 결합 플라즈마(CCP : Capacitively Coupled Plasma)방식이다. 제안된 시스템은 반도체 장비 산업에서 요구되는 높은 생산성을 실현할 수 있다. 본 논문에서는 제안된 시스템의 타당성을 검증하기 위해 CCP와 ICP 결합 임피던스정합 장치를 제작하였고, 이론적 분석과 27.12MHz 와 400kHz의 조건에서 시뮬레이션 및 실험을 진행하였다