• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.643-650
• /
• 2002

The large planar failure has occurred in a rock cut slope of highway construction site in Boeun. This area is considered as unstable since the discontinuities whose orientations are similar to the orientation of the failure plane, are observed in many areas. Therefore, several analysis techniques such as SMR, stereographic analysis, limit equilibrium, numerical analysis, which are commonly used in rock slope stability analysis, are adopted in this area. In order to analyze the stress redistribution and nonlinear displacement caused by cut, which are not obtained in limit equilibrium method, the UDEC and shear strength reduction technique were used in this study Then the factors of safety evaluated by shear strength reduction technique and limit equilibrium were compared. In addition, the factor of safety under fully saturated slope condition was calculated and subsequently, the effect of the reinforcement was evaluated.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.03b
• /
• pp.411-418
• /
• 2000

With the limited amount of budget and time, it is required to determine the priority of investment when there are a large number of hazardous slopes. In this paper, the Rock Slope Risk Rating System is developed based on the combination of the hazard of failure and the damage potential. By applying the proposed rating system to 253 rock slopes in Korean National Highway, it was possible to determine the priority of investment on road cut slopes.

• 한국터널공학회:학술대회논문집
• /
• 2005.04a
• /
• pp.233-247
• /
• 2005

Most tunnel lining material which has been used in the domestic is a concrete. But many problems as the construction period, the cost, and the crack occurrence for the design, construction, and management were happened in the concrete lining. For this reason, many research institutes like the Korea Highway Corporation recognize the necessity of an alternate material development and grow on the interest for that. So in this study, the seismic behaviour characteristics for the application of the Corrugated Steel Plate Lining in cut-and-cover tunnel are evaluated as several conditions for the backfill height, the cutting slope, and the relative density of backfill soil are changed. The compressive stress which is calculated in the Corrugated Steel Plate Lining by the seismic load is decreased as the backfill height increases and the cut slope grows gentle. Also, the moment shows the tendency of decrease according to the increase of the backfill height. But in the case of the relative density of the backfill soil is small, the moment increases according to the increase of the backfill height and affects the dynamic behaviour characteristic. So it is considered that the relative density of the backfill soil is also the important point. As the result in analyzing the seismic response characteristics of the reinforcement spacing of the Corrugated Steel Plate, the variation in the compressive force is hardly happened, but the moment and the shear force increase on the reinforcement spacing being narrow.

• Tunnel and Underground Space
• /
• v.11 no.3
• /
• pp.206-216
• /
• 2001

Many failures in cut slopes occur during and following road construction. Failures are caused, in part, by a lack of understanding of the characteristics of rock mass including its geologic structure. The stability of rock slopes is closely related to factors that include the type of rock, development of geological structures, weathering, characteristics of rock, and the shape of the geologic features. Therefore, it is very important to consider these characteristics of rock mass in the evaluation of rock slope stability. In spite of investigation from many slope failures, these information data were not systematically stored and not efficiently utilized. In this study, a Database system named DB/SLOPE was developed using Oracle for systematic management of cut slopes. The developed database system can be used to estimate of slope stability and to predict of slope failure.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.724-731
• /
• 2006

The purpose of this study is to estimate a landslide using the SLOPILE program from the slope reinforced by slope stability systems such as soil nailing and pile. To do this, cutting slope located at Donghae-Highway in Kwangwon-Do was considered. The behavior of slope was monitored for a long term by using instrumentation according to the reinforcement stages. The sequence of reinforcement stages was followed as pile installation, boring, soil nailing installation, anchoring and embankment. The result from this case study shows that the safety factor of slope depends on the reinforcement stage more or less.

• The Journal of Engineering Geology
• /
• v.18 no.1
• /
• pp.37-44
• /
• 2008

KICT has been carrying out inventory research on the cut slopes of national roads. Inventory research results are basic data to cut slope management system. Inventory data are classified by general status, cut slope characteristics and inspector opinion. Inventory data are utilized to figure out dangerous slopes and decide survey ranking of detailed safety diagnostication. This paper drew the distribution area of dangerous cut slopes using inventory data in Chungcheongdo, and verified efficiency on distribution area of dangerous cut slopes by comparing occurrence frequency of real collapsed cut slopes.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.18 no.6
• /
• pp.215-226
• /
• 2015

This study introduced food waste into re-vegetation base materials for surface loss recovery of carry-away highway cut slope. The object of this study is to derive the mixing ratio of food waste by conducting a test installation, monitoring, analysis and evaluation for recovery of carry-away highway cut slope. The following items were investigated and analyzed each experimental zone to draw mixing ratio of re-vegetation base materials and food waste : the physical and chemical properties of the vegetation base materials, soil-hardness, soil-humidity, left out and the collapsed point, established number of trees, species richness of grass species and tree species, coverage, pest status, and invasion of disturbance species. The re-vegetation method was evaluated by each experiment zone which has different mixing ratio. As a result, experiment zone A was rated 45 points out of 60 rating points as the best re-vegetation method. However, this study result has been derived from one construction and short-term monitoring. In order to derive the suitable and dependable mixing ratio, conducting an objective re-vegetation method evaluation and long-term experiment and monitoring is required.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.19 no.4
• /
• pp.45-59
• /
• 2016

This study introduced wood waste into revegetation base materials for recovery of highway cut slope. The object of this study is to derive the mixing ratio of wood waste, kaoline and silica by conducting a test installation, monitoring, analysis and evaluation. The following items were investigated and analyzed each experimental zone to deduce the mixing ratio of wood waste, kaoline and silica on slope revegetation base materials: the physical and chemical properties of the vegetation base materials, soil-hardness, soil-humidity, collapse and eroded spots, established number of trees, existing species of grass and tree species, vegetation coverage ratio, pest status, and invasion of disturbance species. The revegetation method was evaluated in each experiment zone which had different mixing ratios. As a result, experiment zone C scored 47 points out of 60 as the best revegetation method. However, this result has been derived from just one construction and short-term monitoring. In order to derive the suitable and dependable mixing ratio, conducting an objective revegetation method evaluation and long-term experimenting and monitoring is required.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.1316-1323
• /
• 2005

Most tunnel lining material which has been used in the domestic is a concrete. But many problems as the construction period, the cost, and the crack occurrence for the design, construction, and management were happened in the concrete lining. For this reason, many research institutes like the Korea Highway Corporation recognize the necessity of an alternate material development and grow on the interest for that. So in this study, the behaviour characteristics for the application of the Corrugated Steel Plate Lining in cut-and-cover tunnel are evaluated as several conditions for the backfill height, the cutting slope, and the relative density of backfill soil are changed. In addition, through using that conditions, CHBDC(2000, Canadian Highway Bridge Design Code) is evaluated if it could be applied to the design by comparing with the numerical analysis results. As the behaviour characteristics of the Corrugated Steel Plate Lining by CHBDC and the static numerical analysis are analyzed, both the methods show the same linear increases of the compressive stress according to the increase of the backfill height. The CHBDC of the dead load condition has very similar tendency by comparing with the result of the static numerical analysis.

• The Journal of Engineering Geology
• /
• v.13 no.2
• /
• pp.157-170
• /
• 2003

This study is performed to investigate the cause of slope failure and to suggest suitable stabilization methods for the failed rock slopes. The slope which is located along the national highway between Maesan and Kakok in Dangjin-gun failed during the construction of roads. Site investigation, drilling program, field measurements, rainfall records, and stability analyses are used to investigate the cause of the slope failure. The problem determining the cut-slope angle based on the existing design manual for the construction of roads is reviewed based on the case history given in this paper. If weakness layer and geological structures such as folds and faults are developed in a slope, slope failure is possible even though the direction of slope and the direction of discontinuities depart more than $30^{\circ}$.