• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.172-173
• /
• 2012

Currently GaN based LED is known to show high internal or external efficiency at low current range. However, this LED operation occurs at high current range and in this range, a significant performance degradation known as 'efficiency droop' occurs. Auger process, carrier leakage process, field effect due to lattice mismatch and thermal effects have been discussed as the causes of loss of efficiency, and these phenomena are major hindrance in LED performance. In order to investigate the main effects of efficiency loss and overcome such effects, it is essential to obtain relative proportion of measurements of internal quantum efficiency (IQE) and various radiative and nonradiative recombination processes. Also, it is very important to obtain radiative and non-radiative recombination times in LEDs. In this research, we measured the IQE of InGaN/GaN multiple quantum wells (MQWs) LEDs with PSS and Planar substrate using modified ABC equation, and investigated the physical mechanism behind by analyzing the emission energy, full-width half maximum (FWHM) of the emission spectra, and carrier recombination dynamic by time-resolved electroluminescence (TREL) measurement using pulse current generator. The LED layer structures were grown on a c-plane sapphire substrate and the active region consists of five 30 ${\AA}$ thick In0.15Ga0.85N QWs. The dimension of the fabricated LED chip was $800um{\times}300um$. Fig. 1. is shown external quantum efficiency (EQE) of both samples. Peak efficiency of LED with PSS is 92% and peak efficiency of LED with planar substrate is 82%. We also confirm that droop of PSS sample is slightly larger than planar substrate sample. Fig. 2 is shown that analysis of relation between IQE and decay time with increasing current using TREL method.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1270-1271
• /
• 2008

Effects of thin ZnO/Mg interlayers on electrical and optical properties between p-GaN and ITO were characterized for its application to GaN-LEDs. The ZnO and Mg layers were deposited to have various thicknesses (1${\sim}$6nm for ZnO and 1${\sim}$2nm for Mg) by sputtering. After RTA process, the atomic migration between Mg and ZnO and the formation of Ga vacancy were observed from SIMS depth profile, resulting in the increase of hole concentration and the reduction of band bending at the surface region of p-GaN. The sample using ZnO(2nm)/Mg(2nm) interlayer produced the lowest contact resistance with SBH(Schottky barrier height) of 0.576 eV and the transmittance higher than 83% at a wavelength of 460nm when annealed at 500$^{\circ}C$ for 3min in air ambient.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.160-160
• /
• 2010

In this work, we investigate ohmic contacts to p-type GaN using a Pt/Cu/Au metallization scheme in order to achieve low resistance and thermally stable ohmic contact on p-GaN. An ohmic contact formed by a metal electrode deposited on a highly doped InGaN/GaN superlattice sturucture on p-GaN layer. The specific contact resistance is $1.56{\times}10^{-6}{\Omega}cm^2$ for the as-deposited sample, $1.35{\times}10^{-4}{\Omega}cm^2$ for the sample annealed at $250^{\circ}C$ and $6.88{\times}10^{-3}{\Omega}cm^2$ for the sample annealed at $300^{\circ}C$.

• Journal of the Korean Vacuum Society
• /
• v.17 no.3
• /
• pp.211-214
• /
• 2008

GaN-based light-emitting diodes (LEDs) of a 405 nm wavelength have been fabricated on a sapphire substrate by metal organic chemical vapor deposition (MOCVD). In order to reflect the photons, which are generated in the InGaN active region and emitted to the backside, to the front surface, a reflection layer was deposited onto the back of the substrate. Aluminum was used as the reflection layer and Al was deposited on the sample followed by Ti evaporation for firm adhesion of the reflection layer to the substrate. The light extraction efficiency was enhanced 52 % by adoption of the Ti-Al reflection layer.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.7
• /
• pp.1-8
• /
• 2012

In this paper, we improved the light extraction efficiency by structural change of LEDs on conventional LEDs. We simulated the LEDs light emission as functions of LED side wall angle, various refractive indices the geometrical structures and analyzed the condition improved the light efficiency. We present the results of experimerns and simulations for light output power from LEDs for various refractive indices and the geometrical structures of the LED encapsulants. When the side wall angle range was from 40[$^{\circ}$] to 30[$^{\circ}$], the LED emission increased. LED side wall angle onto LED using the simulation system with a fine tuning of the structure of the LEDs side wall angle is fabricated. Additionally, we changed the side wall angle of LED package with spherical structure and flat structure. The result of spherical structure ray tracting is higher compared with flat structure about 14[%].

• Korean Journal of Materials Research
• /
• v.21 no.5
• /
• pp.250-254
• /
• 2011

We have synthesized bluish-green, highly-efficient $BaSi_2O_2N_2:Eu^{2+}$ and $(Ba,Sr)Si_2O_2N_2:Eu^{2+}$ phosphors through a conventional solid state reaction method using metal carbonate, $Si_3N_4$, and $Eu_2O_3$ as raw materials. The X-ray diffraction (XRD) pattern of these phosphors revealed that a $BaSi_2O_2N_2$ single phase was obtained. The excitation and emission spectra showed typical broadband excitation and emission resulting from the 5d to 4f transition of $Eu^{2+}$. These phosphors absorb blue light at around 450 nm and emit bluish-green luminescence, with a peak wavelength at around 495 nm. From the results of an experiment involving Eu concentration quenching, the relative PL intensity was reduced dramatically for Eu = 0.033. A small substitution of Sr in place of Ba increased the relative emission intensity of the phosphor. We prepared several white LEDs through a combination of $BaSi_2O_2N_2:Eu^{2+}$, YAG:$Ce^{3+}$, and silicone resin with a blue InGaN-based LED. In the case of only the YAG:$Ce^{3+}$-converted LED, the color rendering index was 73.4 and the efficiency was 127 lm/W. In contrast, in the YAG:$Ce^{3+}$ and $BaSi_2O_2N_2:Eu^{2+}$-converted LED, two distinct emission bands from InGaN (450 nm) and the two phosphors (475-750 nm) are observed, and combine to give a spectrum that appears white to the naked eye. The range of the color rendering index and the efficiency were 79.7-81.2 and 117-128 lm/W, respectively. The increased values of the color rendering index indicate that the two phosphor-converted LEDs have improved bluish-green emission compared to the YAG:Ce-converted LED. As such, the $BaSi_2O_2N_2:Eu^{2+}$ phosphor is applicable to white high-rendered LEDs for solid state lighting.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.23-23
• /
• 2009

GaN-based nitride semiconductors have attracted considerable attention in high-brightness light-emitting-diodes (LEDs) and laser diodes (LDs) covering from green to ultraviolet spectral range. LED and LD heterostructures are usually grown on (0001)-$Al_2O_3$. The large lattice mismatch between $Al_2O_3$ substrates and the GaN layers leads to a high density of defects(dislocations and stacking faults). Moreover, Ga and N atoms are arranged along the polar [0001] crystallographic direction, which leads to spontaneous polarization. In addition, in the InGaN/GaN MQWs heterostructures, stress applied along the same axis can also give rise to piezoelectric polarization. The total polarization, which is the sum of spontaneous and piezoelectric polarizations, is aligned along the [0001] direction of the wurtzite heterostructures. The change in the total polarization across the heterolayers results in high interface charge densities and spatial separation of the electron and hole wave functions, redshifting the photoluminescence peak and decreasing the peak intensity. The effect of polarization charges in the GaN-based heterostructures can be eliminated by growing along the non-polar [$11\bar{2}0$] (a-axis) or [$1\bar{1}00$] (m-axis) orientation instead of thecommonly used polar [0001] (c-axis). For non-polar GaN growth on non-polar substrates, the GaN films have high density of planar defects (basal stacking fault BSFs, prismatic stacking fault PSFs), because the SFs are formed on the basal plane (c-plane) due to their low formation energy. A significant reduction in defect density was recently achieved by applying blocking layer such as SiN, AlN, and AlGaN in non-polar GaN. In this work, we were performed systematic studies of the defects in the nonpolar GaN by conventional and high-resolution transmission electron microscopy.

• Journal of the Optical Society of Korea
• /
• v.16 no.4
• /
• pp.349-353
• /
• 2012

Uniform spreading of injection current in light-emitting diodes (LEDs) is one of the crucial requirements for better device performances. It is reported that non-uniform current spreading leads to low output power, high current crowding, heating, and reliability degradation of the LED device. This paper reports on the effects of different surface and electrode geometries in the LEDs. To increase the output power of LEDs and reduce the series resistance, a rectangular-type LED (RT-LED) with a centered island cathode has been fabricated and investigated by comparison with a conventional LED (CV-LED). The performances of RT-LEDs were prominently enhanced via uniform current spreading and low current crowding. Performances in terms of increased output power and lower forward voltage of simulated RT-LEDs are much superior to those of CV-LEDs. Based on these results, we investigated the correlation between device geometries and optical characteristics through the fabricated CV and RT-LEDs. The measured output power and forward voltage of the RT-LEDs at 100 mA are 64.7% higher and 8% smaller compared with those of the CV-LEDs.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.4
• /
• pp.85-89
• /
• 2021

AlGaN-based UV-C light-emitting diodes (LEDs) were applied for p-type activation by electrochemical potentiostatic activation (EPA). The p-type activation efficiency was increased by removing hydrogen atoms through EPA treatment using a neutral Mg-H complex that causes high resistance and low conductivity. A neutral Mg-H complex is decomposed into Mg^- and H⁺ depending on the key parameters of solution, voltage, and time. The improved hole carrier concentration was confirmed by secondary ion mass spectroscopy (SIMS) analysis. This mechanism eventually improved the internal quantum efficiency (IQE), the light extraction efficiency, the leakage current value in the reverse current region, and junction temperature, resulting in better UV-C LED lifetime. For systematic analysis, SIMS, Etamax IQE system, integrating sphere, and current-voltage measurement system were used, and the results were compared with the existing N₂-annealing method.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.23.2-23.2
• /
• 2011

This presentation will include an overview of III-Nitride LED technology, applications, key areas for future improvements, challenges such as efficiency droop. GaN-based high-power light-emitting diodes (LEDs) suffer from high-current loss mechanisms that lead to a significant decrease in internal quantum efficiency at high drive currents, a well-known phenomenon commonly referred to as efficiency droop. Although many attempts have been made to uncover this LED's darkest secret, there is still a lack of consensus on the dominant mechanism responsible for this detrimental phenomenon. In this presentation, proposed origins and corresponding solutions to the droop-causing mechanisms will be reviewed and discussed.