• 대한전자공학회논문지SD
• /
• 제49권6호
• /
• pp.1-8
• /
• 2012

본 논문은 패키징 인덕터를 이용한 완전 집적화된 DC-DC 벅 컨버터를 소개한다. 사용된 패키징 인덕터는 본딩 와이어와 리드 프레임의 기생 인덕턴스를 포함한다. 이들은 실리콘 위에서 구현되는 온-칩 인덕터 보다 높은 Q 인자를 가진다. 또한 본 논문은 고주파 스위칭 컨버터의 효율적인 레귤레이션을 위해 로우-스윙 게이트 드라이버를 제안한다. 로우-스윙 드라이버는 다이오드-커넥티드 트랜지스터의 전압 드롭을 이용한다. 제안된 컨버터는 $0.13-{\mu}m$ CMOS 공정을 통해 설계 및 제작되었다. 제작된 벅 컨버터의 효율은 입출력 전압비가 3.3 V/ 2.0 V와 2.8 V/ 2.3 V 일 때, 각각 68.7%, 86.6%로 측정되었다.

• 한국산업융합학회 논문집
• /
• 제21권6호
• /
• pp.265-271
• /
• 2018

DC-DC buck converter is a critical building block in the power management integrated circuit (PMIC) architecture for the portable devices such as cellular phone, personal digital assistance (PDA) because of its power efficiency over a wide range of conversion ratio. To ensure a safe operation, avoid unexpected damages and enhance the reliability of the converter, fully-integrated protection circuits such as over voltage protection (OVP), under voltage lock out (UVLO), startup, and thermal shutdown (TSD) blocks are designed. In this paper, these three fully-integrated protection circuit blocks are proposed for use in the DC-DC buck converter. The buck converter with proposed protection blocks is operated with a switching frequency of 1 MHz in continuous conduction mode (CCM). In order to verify the proposed scheme, the buck converter has been designed using a 180 nm CMOS technology. The UVLO circuit is designed to track the input voltage and turns on/off the buck converter when the input voltage is higher/lower than 2.6 V, respectively. The OVP circuit blocks the buck converter's operation when the input voltage is over 3.3 V, thereby preventing the destruction of the devices inside the controller IC. The TSD circuit shuts down the converter's operation when the temperature is over $85^{\circ}C$. In order to verify the proposed scheme, these protection circuits were firstly verified through the simulation in SPICE. The proposed protection circuits were then fabricated and the measured results showed a good matching with the simulation results.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.71-71
• /
• 2009

This paper describes a simple, on-chip CMOS compatible the thin-film inductor applied for the dc-dc converters. A fully CMOS-compatible thin-film inductor with a bottom NiFe core is integrated with the DC-DC converter circuit on the same chip. By eliminating ineffective top magnetic layer, very simple process integration was achieved. Fabricated monolithic thin film inductor showed fairly high inductance of 2.2 ${\mu}H$ and Q factor of 11.2 at 5MHz. When the DC-DC converter operated at $V_{in}=3.3V$ and 5MHz frequency, it showed output voltage $V_{out}=8.0V$, and corresponding power efficiency was 85%.

• ETRI Journal
• /
• 제25권4호
• /
• pp.270-273
• /
• 2003

This paper presents a simple process to integrate thin-film inductors with a bottom NiFe magnetic core. NiFe thin films with a thickness of 2 to 3${\mu}m$ were deposited by sputtering. A polyimide buffer layer and shadow mask were used to relax the stress of the NiFe films. The fabricated double spiral thin-film inductor showed an inductance of 0.49${\mu}H$ and a Q factor of 4.8 at 8 MHz. The DC-DC converter with the monolithically integrated thin-film inductor showed comparable performances to those with sandwiched magnetic layers. We simplified the integration process by eliminating the planarization process for the top magnetic core. The efficiency of the DC-DC converter with the monolithic thin-film inductor was 72% when the input voltage and output voltage were 3.5 V and 6 V, respectively, at an operating frequency of 8 MHz.

• Transactions on Electrical and Electronic Materials
• /
• 제11권1호
• /
• pp.24-28
• /
• 2010

A simulation study of a current-mode direct current (DC)-DC buck converter is presented in this paper. The converter, with a fully integrated power module, is implemented by using sense method metal-oxide-semiconductor field-effect transistor (MOSFET) and bipolar complementary metal-oxide-semiconductor (BiCMOS) technology. When the MOSFET is used in a current sensor, the sensed inductor current with an internal ramp signal can be used for feedback control. In addition, the BiCMOS technology is applied in the converter for an accurate current sensing and a low power consumption. The DC-DC converter is designed using the standard $0.35\;{\mu}m$ CMOS process. An off-chip LC filter is designed with an inductance of 1 mH and a capacitance of 12.5 nF. The simulation results show that the error between the sensing signal and the inductor current can be controlled to be within 3%. The characteristics of the error amplification and output ripple are much improved, as compared to converters using conventional CMOS circuits.

• 한국전기전자재료학회논문지
• /
• 제16권2호
• /
• pp.138-143
• /
• 2003

A double spiral thin-film inductor with a NiFe magnetic core is integrated with DC-DC converter IC. The NiFe core is deposited on a polyimide film as the thinckness of NiFe is 2.5~3.5 ${\mu}$m. Then, copper conductor line is deposited on the NiFe core with double spiral structure. Process integration is performed by sequential processes of etching the polyimide film deposited both top and bottom of the NiFe core and electroplation copper conductor line from exposed metal pad of the DC-DC converter IC. Process integration is simplified by elimination planarization process for top core because the proposed thin-film inductor has a bottom NiFe core only. Inductor of the fabricated monolithic DC-DC converter IC is 0.53 ${\mu}$H when the area of converter IC and thin-film inductor are 5X5$\textrm{mm}^2$ and 3.5X2.5$\textrm{mm}^2$, respectively. The efficiency is 72% when input voltage and output voltage are 3.5 V and 6 V, respectively at the operation frequency of 8 MHz.

• Transactions on Electrical and Electronic Materials
• /
• 제12권6호
• /
• pp.262-266
• /
• 2011

A simulation study of a current-mode direct current (DC)-DC boost converter is presented in this paper. This converter, with a fully-integrated power module, is implemented by using bipolar complementary metal-oxide semiconductor (BiCMOS) technology. The current-sensing circuit has an op-amp to achieve high accuracy. With the sense metal-oxide semiconductor field-effect transistor (MOSFET) in the current sensor, the sensed inductor current with the internal ramp signal can be used for feedback control. In addition, BiCMOS technology is applied to the converter, for accurate current sensing and low power consumption. The DC-DC converter is designed with a standard 0.35 ${\mu}m$ BiCMOS process. The off-chip inductor-capacitor (LC) filter is operated with an inductance of 1 mH and a capacitance of 12.5 nF. Simulation results show the high performance of the current-sensing circuit and the validity of the BiCMOS converter. The output voltage is found to be 4.1 V with a ripple ratio of 1.5% at the duty ratio of 0.3. The sensing current is measured to be within 1 mA and follows to fit the order of the aspect ratio, between sensing and power FET.

• 한국산학기술학회논문지
• /
• 제17권7호
• /
• pp.42-48
• /
• 2016

본 논문에서는 플라이백 DC-DC 컨버터에 사용되는 출력전압 정보를 보다 정확하게 감지하는 피크검출기를 집적회로로 설계하였다. 제안하는 피크검출기의 회로는 하나의 op-amp와 세 개의 트랜지스터로 이루어져 있다. 제안하는 회로는 단순한 구조로 이루어져 있기 때문에 제안하는 회로는 출력전압을 감지하는 과정에서 지연시간을 최소화 할 수 있다. 회로에서 op-amp와 몇 개의 트랜지스터를 사용함으로써, 제안하는 피크검출기가 종래의 커패시터와 다이오드로 설계된 피크검출기를 대신해 칩의 집적화가 가능해지고, 플라이백 컨버터의 모듈을 구성하는 소자가 트랜지스터로 대체되고 칩의 면적이 줄어들어 가격을 줄일 수 있다. 제안하는 회로는 0.35 um CMOS 공정을 이용하여 칩으로 제작하여 측정하였고, 칩 측정결과 모의실험결과와 잘 일치함을 보였다. 시뮬레이션 결과 사인파의 입력신호를 출력신호가 최대 0.3 ~ 3.1 %의 오차 범위 내에서 피크전압을 유지하는 것을 확인하였다. 칩 측정결과 모의실험결과와 잘 일치함을 보였다. 제안하는 회로의 결과를 통하여 종래의 피크검출기 회로의 좋지 않은 레귤레이션을 향상시키기 위하여 높은 플라이백 컨버터의 동작을 보일 수 있다. 플라이백 컨버터의 출력전압을 정확하게 감지하여 안정적인 컨버터 동작을 할 수 있을 것으로 사료된다.

• Journal of Power Electronics
• /
• 제10권6호
• /
• pp.611-620
• /
• 2010

This paper presents a new architecture, called "Power Electronics Remote Wiring and Measurement Laboratory (PermLAB)", that translates a common gateway interface (CGI) string from a remote web user to a web server connected to a 3-dimension switching matrix board, can be used to switch on and off, and to control a cluster of instruments and components. PermLAB addresses real-time connection, switching, and data acquisition over the Internet instead of using simulated data. A software procedure uses a signature system to identify each instrument and component in a complex system. The Web-server application is developed in HTML, JavaScript and Java, and in C language for the CGI interface, which resides in a controller portion of LabVIEW. The LabVIEW software fully integrates the Web sever, LabVIEW data acquisition boards and controllers, and the 3-dimensional switching matrix board. The paper will analyze a half-wave rectifier (AC - DC converter) circuit connected over the Internet using the PermLAB. PermLAB allows students to obtain real data by real-time wiring of real circuits in the laboratory using a "virtual breadboard" on the Web. The software for the Web-based 3-dimensional system is flexible, portable, can be integrated into many laboratory applications or expanded, and easily accessible worldwide.

• 대한전자공학회논문지SD
• /
• 제43권11호
• /
• pp.58-68
• /
• 2006

본 논문에서는 차세대 디지털 TV 및 무선 랜 등과 같이 고속에서 저전압, 저전력 및 소면적을 동시에 요구하는 고성능 집적시스템을 위한 10b 250MS/s $1.8mm^2$ 85mW 0.13um CMOS A/D 변환기 (ADC)를 제안한다. 제안하는 ADC는 요구되는 10b 해상도에서 250MS/s의 아주 빠른 속도 사양을 만족시키면서, 면적 및 전력 소모를 최소화하기 위해 3단 파이프라인 구조를 사용하였다. 입력단 SHA 회로는 게이트-부트스트래핑 (gate-bootstrapping) 기법을 적용한 샘플링 스위치 혹은 CMOS 샘플링스위치 등 어떤 형태를 사용할 경우에도 10비트 이상의 해상도를 유지하도록 하였으며, SHA 및 두개의 MDAC에 사용되는 증폭기는 트랜스컨덕턴스 비율을 적절히 조정한 2단 증폭기를 사용함으로써 10비트에서 요구되는 DC 전압 이득과 250MS/s에서 요구되는 대역폭을 얻음과 동시에 필요한 위상 여유를 갖도록 하였다. 또한, 2개의 MDAC의 커패시터 열에는 소자 부정합에 의한 영향을 최소화하기 위해서 인접신호에 덜 민감한 향상된 3차원 완전 대칭 구조의 커패시터 레이아웃 기법을 제안하였으며, 기준 전류 및 전압 발생기는 온-칩 RC 필터를 사용하여 잡음을 최소화하고, 필요시 선택적으로 다른 크기의 기준 전압을 외부에서 인가할 수 있도록 설계하였다. 제안하는 시제품 ADC는 0.13um 1P8M CMOS 공정으로 제작되었으며, 측정된 DNL 및 INL은 각각 최대 0.24LSB, 0.35LSB 수준을 보여준다. 또한, 동적 성능으로는 200MS/s와 250MS/s의 동작 속도에서 각각 최대 54dB, 48dB의 SNDR과 67dB, 61dB의 SFDR을 보여준다. 시제품 ADC의 칩 면적은 $1.8mm^2$이며 전력 소모는 1.2V 전원 전압에서 최대 동작 속도인 250MS/s일 때 85mW이다.