• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.127-130
• /
• 2003

An RSFQ (Rapid Single Flux Quantum) counter can be used as a frequency divider that was an essential part of a programmable voltage standard chip. The voltage standard chip is composed of two circuit parts, a counter and an antenna Analog signal of tens to hundreds ㎓ may be applied to a finline antenna part. This analog signal can be converted to the stream of SFQ voltage pulses by a DC/SFQ circuit. The number of voltage pulses can be reduced by 2n times when they pass through a counter that is composed of n T Flip-Flops (Toggle Flip-Flop). Such a counter can be used not only as a frequency divider, but also to build a programmable voltage standard chip. So, its application range can be telecommunication, high speed RAM, microprocessor, etc. In this work, we have used Xic, WRspice, and L-meter to design an RSFQ counter. After circuit optimization, we could obtain the bias current margins of the T Flip-Flop circuit to be above 31％ Our RSFQ counter circuit designs were based on the 1 ㎄/$\textrm{cm}^2$ niobium trilayer technology.

• Journal of IKEEE
• /
• v.8 no.1 s.14
• /
• pp.145-151
• /
• 2004

For wide-band spread spectrum communication systems such as IMT-2000, a digital matched filter is a key device for rapid spreading code synchronization. Although a digital matched filter can be implemented easily, large power consumption at the higher chip rate and large summation delay of longer chip length are the bottleneck of practical use. In this paper, we propose a optimized partial correlation digital matched filter structure which can be constructed of the so-called generalized hierarchical Golay sequence. a partial correlation structure can reduce the number of correlators, but enlarge the size of flip-flops. In this paper, The proposed approach focuses on efficient circuit size, power dissipation, maintaining the operating throughput. A proposed digital matched filter reduce the size of flip-flops by rounding method. and it reduces about 45 percentages of power dissipation and chip area as compared with digital matched filter which is not rounded. rounding. The proposed architecture was verified by using Xilinx FPGA.

• The Transactions of the Korea Information Processing Society
• /
• v.3 no.5
• /
• pp.1346-1353
• /
• 1996

In this paper, we propose a modeling method for the flip-flops and test generation algorithms to detect the faults in the sequential circuits using VHDL in the high-level design environment. RS, JK, D and T flip-flops are modeled using data flow types. The sequence of micro-operation which is the basic structure of a chip-level leads to a control point where varnishing occurs to one of two micro- operation sequence. In order to model the fault of one micro-operation(FMOP) that perturb another micro-operation effectively, the concept of goal trees and some heuristic rules are used. Given a faulty FMOP or fault of control point (FCON), a test pattern is generated by fault sensitization, path sensitization and determination of the imput combinations that will justify the path sensitization. The fault models are restricted to the data flow model in the ARCHITECTURE statement of VHDL. The proposed algorithm is implemented in the C language and its efficiency is confirmed by some examples.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.3
• /
• pp.404-416
• /
• 2015

Small-area, low-power coarse and fine frequency detectors (FDs) are proposed for an adaptive bandwidth referenceless CDR with a wide range of input data rate. The coarse FD implemented with two flip-flops eliminates harmonic locking as long as the initial frequency of the CDR is lower than the target frequency. The fine FD samples the incoming input data by using half-rate four phase clocks, while the conventional rotational FD samples the full-rate clock signal by the incoming input data. The fine FD uses only a half number of flip-flops compared to the rotational FD by sharing the sampling and retiming circuitry with PLL. The proposed CDR chip in a 65-nm CMOS process satisfies the jitter tolerance specifications of both USB 3.0 and USB 3.1. The proposed CDR works in the range of input data rate; 2 Gb/s ~ 8 Gb/s at 1.2 V, 4 Gb/s ~ 11 Gb/s at 1.5 V. It consumes 26 mW at 5 Gb/s and 1.2 V, and 41 mW at 10 Gb/s and 1.5 V. The measured phase noise was -97.76 dBc/Hz at the 1 MHz frequency offset from the center frequency of 2.5 GHz. The measured rms jitter was 5.0 ps at 5 Gb/s and 4.5 ps at 10 Gb/s.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.11
• /
• pp.187-192
• /
• 2014

Various researches are performed to extract significant features from continuous images. The FAST algorithm has the simple structure for arithmetic operation and it is easy to extraction the features in real time. For this reason, the FPGA based hardware accelerator is implemented and widely applied for the FAST algorithm. The hardware accelerator needs the threshold to extract the features from images. The threshold is influenced not only the number of extracted features but also the total execution time. Therefore, the way of threshold control is important to stabilize the total execution time and to extract features as much as possible. In order to control the threshold, this paper proposes the PI controller. The function and performance for the proposed PI controller are verified by using test images and the PI control logic is designed based on Xilinx Vertex IV FPGA. The proposed scheme can be implemented by adding 47 Flip Flops, 146 LUTs, and 91 Slices to the FAST hardware accelerator. This proposed approach only occupies 2.1% of Flip Flop, 4.4% of LUTs, and 4.5% of Slices and can be regarded as a small portion of hardware cost.

• The Journal of the Convergence on Culture Technology
• /
• v.7 no.1
• /
• pp.558-563
• /
• 2021

Quantum-Dot Cellular Automata is a next-generation nanocircular design technology that is drawing attention from many research organizations not only because it is possible to design efficient circuits by overcoming the physical size limitations of existing CMOS circuits, but also because of its energy-efficient features. In this paper, one of the existing digital circuits, T flip-flop circuit, is proposed using QCA. The previously proposed T flip-flops are designed based on the majority gate, so the circuits are complex and have long delays. Therefore, the design of the XOR gate-based T flip-flop using cell interaction reduces circuit complexity and minimizes latency. The proposed circuit is simulated using QCADesigner, and the performance is compared and analyzed with the existing proposed circuits.

• The KIPS Transactions:PartA
• /
• v.11A no.1
• /
• pp.1-10
• /
• 2004

A cellular array parallel multiplier with parallel-inputs and parallel-outputs for performing the multiplication of two polynomials in the finite fields GF$(2^m)$ is presented in this paper. The presented cellular way parallel multiplier consists of three operation parts: the multiplicative operation part (MULOP), the irreducible polynomial operation part (IPOP), and the modular operation part (MODOP). The MULOP and the MODOP are composed if the basic cells which are designed with AND Bates and XOR Bates. The IPOP is constructed by XOR gates and D flip-flops. This multiplier is simulated by clock period l${\mu}\textrm{s}$ using PSpice. The proposed multiplier is designed by 24 AND gates, 32 XOR gates and 4 D flip-flops when degree m is 4. In case of using AOP irreducible polynomial, this multiplier requires 24 AND gates and XOR fates respectively. and not use D flip-flop. The operating time of MULOP in the presented multiplier requires one unit time(clock time), and the operating time of MODOP using IPOP requires m unit times(clock times). Therefore total operating time is m+1 unit times(clock times). The cellular array parallel multiplier is simple and regular for the wire routing and have the properties of concurrency and modularity. Also, it is expansible for the multiplication of two polynomials in the finite fields with very large m.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.5
• /
• pp.443-450
• /
• 2013

This paper propose a new ROM data encoding method that takes into account of a sequential access pattern to reduce the power consumption in ROMs used in applications such as FIR filters that access the ROM sequentially. In the proposed encoding method, the number of 1's, of which the increment leads to the increase of the power consumption, is reduced by applying an exclusive-or (XOR) operation to a bit pair composed of two consecutive bits in a bit line. The encoded data can be decoded by using XOR gates and D flip-flops, which are usually used in digital systems for synchronization and glitch suppression. By applying the proposed encoding method to coefficient ROMs of FIR filters designed by using various design methods, we can achieve average reduction of 43.7% over the unencoded original data in the power consumption, which is larger reduction than those achieved by previous methods.

• The Transactions of the Korea Information Processing Society
• /
• v.2 no.3
• /
• pp.425-432
• /
• 1995

In this paper we propose a design and implementation technique of a universal automatic test pattern generator(UATPG) which is well suited for VLSI digital circuits. UATPG is designed to extend the capabilities of the existing APTG and to provide a convenient environment to computer-aided design(CAD) users. We employ heuristic techniques in line justification and fault propagation for functional gates during test pattern generation for a target fault. In addition, the flip-flops associated with design for testability (DFT) are exploited for pseudo PIs and pseudo POs to enhance the testabilities of VLSI circuits. As a result, UATPG shows a good enhancement in convenient usage and performance.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.10
• /
• pp.52-62
• /
• 2003

This paper discusses ternary logic gate, ternary D flip-flop, and ternary four-digit parallel input/output register. The ternary logic gates consist of n-channel pass transistors and neuron MOS(νMOS) threshold inverters on voltage mode. They are designed with a transmission function using threshold inverter that are in turn, designed using Down Literal Circuit(DLC) that has various threshold voltages. The νMOS pass transistor is very suitable gate to the multiple-valued logic(MVL) and has the input signal of the multi-level νMOS threshold inverter. The ternary D flip-flop uses the storage element of the ternary data. The ternary four-digit parallel input/output register consists of four ternary D flip-flops which can temporarily store four-digit ternary data. In this paper, these circuits use 3.3V low power supply voltage and 0.35m process parameter, and also represent HSPICE simulation result.