• Korean Journal of Metals and Materials
• /
• v.50 no.10
• /
• pp.785-792
• /
• 2012

A new flip chip structure consisting of interlocking joints locally surrounded by non-conductive adhesive was investigated in order to improve the contact resistance characteristics and prevent the parasitic capacitance increase. The average contact resistance of the interlocking joints was substantially reduced from $135m{\Omega}$ to $79m{\Omega}$ by increasing the flip chip bonding pressure from 85 MPa to 185 MPa. Improvement of the contact resistance characteristics at higher bonding pressure was attributed not only to the increased contact area between Cu chip bumps and Sn pads, but also to the severe plastic deformation of Sn pads caused during formation of the interlocking-joint structure. The parasitic capacitance increase due to the non-conductive adhesive locally surrounding the flip chip joints was estimated to be as small as 12.5%.

• Korean Journal of Materials Research
• /
• v.20 no.12
• /
• pp.681-685
• /
• 2010

The application of flip chip technology has been growing with the trend of miniaturization of electronic packages, especially in mobile electronics. Currently, several types of adhesive are used for flip chip bonding and these adhesives require some special properties; they must be solvent-free and fast curing and must ensure joint reliability against thermal fatigue and humidity. In this study, imidazole and its derivatives were added as curing catalysts to epoxy resin and their effects on the adhesive properties were investigated. Non-isothermal DSC analyses showed that the curing temperatures and the heat of reaction were dependent primarily on the type of catalyst. Isothermal dielectric analyses showed that the curing time was dependent on the amount of catalysts added as well as their type. The die shear strength increased with the increase of catalyst content while the Tg decreased. From this study, imidazole catalysts with low molecular weight are expected to be beneficial for snap curing and high adhesion strength for flip chip bonding applications.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.1 s.34
• /
• pp.9-16
• /
• 2005

This paper presents the development of new anisotropic conductive adhesives with enhanced thermal conductivity for the wide use of adhesive flip chip technology with improved reliability under high current density condition. The continuing downscaling of structural profiles and increase in inter-connection density in flip chip packaging using ACAs has given rise to reliability problem under high current density. In detail, as the bump size is reduced, the current density through bump is also increased. This increased current density also causes new failure mechanism such as interface degradation due to inter-metallic compound formation and adhesive swelling due to high current stressing, especially in high current density interconnection, in which high junction temperature enhances such failure mechanism. Therefore, it is necessary for the ACA to become thermal transfer medium to improve the lifetime of ACA flip chip joint under high current stressing condition. We developed thermally conductive ACA of 0.63 W/m$\cdot$K thermal conductivity using the formulation incorporating $5 {\mu}m$ Ni and $0.2{\mu}m$ SiC-filled epoxy-bated binder system to achieve acceptable viscosity, curing property, and other thermo-mechanical properties such as low CTE and high modulus. The current carrying capability of ACA flip chip joints was improved up to 6.7 A by use of thermally conductive ACA compared to conventional ACA. Electrical reliability of thermally conductive ACA flip chip joint under current stressing condition was also improved showing stable electrical conductivity of flip chip joints. The high current carrying capability and improved electrical reliability of thermally conductive ACA flip chip joint under current stressing test is mainly due to the effective heat dissipation by thermally conductive adhesive around Au stud bumps/ACA/PCB pads structure.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.3 no.3
• /
• pp.122-131
• /
• 2003

In this study, some characteristics of conductive and non-conductive adhesive inter-connections are derived, based on data from literature and own projects. Assembly of flip chip on flex is taken as a carrier. Potential failure mechanisms of adhesive interconnections reported in literature are reviewed. Some methods that can be used to evaluate the quality of adhesive interconnections and to evaluate their aging behavior are given. Possible finite element simulation approaches are introduced and the required critical materials properties are summarized. Response to temperature and moisture, resistance to reflow soldering and resistance to rapid change in temperature and humidity are elaborated. The effect of post cure during accelerated testing is discussed. This study shows that only a combined approach using finite element simulations, and use of appropriate experimental evaluation methods can result in revealing, understanding and quantifying the complex degradation mechanisms of adhesive interconnections during aging.

• Journal of Welding and Joining
• /
• v.33 no.5
• /
• pp.41-46
• /
• 2015

The snap cure NCP(non-conducive paste) adhesive material is essentially required for the high productivity flip chip bonding process. In this study, the accessibility of DEA(dielectric analysis) method for the evaluation of snap cure behavior was investigated with comparison to the isothermal DSC(differential scanning calorimetry) method. NCP adhesive was mainly formulated with epoxy resin and imidazole curing agent. Even though there were some noise in the dielectric loss factor curve measured by DEA, the cure start and completion points could be specified clearly through the data processing of cumulation and deviation method. Degree of cure by DEA method which was measured from the variation of the dielectric loss factor of adhesive material was corresponded to about 80% of the degree of cure by DSC method which was measured from the heat of curing reaction. Because the adhesive joint cured to the degree of 80% in the view point of chemical reaction reveals the sufficient mechanical strength, DEA method is expected to be used effectively in the estimation of the high speed curing behavior of snap cure type NCP adhesive material for flip chip bonding.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2000.10a
• /
• pp.7-38
• /
• 2000

Performance, reliability, form factor drive flip chip use. BGAs and CSPs will provide stepping stone to FC DCA .Growing vendor infrastructure - Low cost, high density organic substrates -New generations of fluxes and underfills .Adhesives flip chip technology as a low cost flip chip alternatives -Low cost Au stud or Electroless Ni bumps -Reliable thermal cycling and electrical performance.

• Korean Journal of Materials Research
• /
• v.22 no.9
• /
• pp.454-458
• /
• 2012

Various adhesive materials are used in flip chip packaging for electrical interconnection and structural reinforcement. In cases of COF(chip on film) packages, low temperature bonding adhesive is currently needed for the utilization of low thermal resistance substrate films, such as PEN(polyethylene naphthalate) and PET(polyethylene terephthalate). In this study, the effects of anhydride and dihydrazide hardeners on the low-temperature snap cure behavior of epoxy based non-conductive pastes(NCPs) were investigated to reduce flip chip bonding temperature. Dynamic DSC(differential scanning calorimetry) and isothermal DEA(dielectric analysis) results showed that the curing rate of MHHPA(hexahydro-4-methylphthalic anhydride) at $160^{\circ}C$ was faster than that of ADH(adipic dihydrazide) when considering the onset and peak curing temperatures. In a die shear test performed after flip chip bonding, however, ADH-containing formulations indicated faster trends in reaching saturated bond strength values due to the post curing effect. More enhanced HAST(highly accelerated stress test) reliability could be achieved in an assembly having a higher initial bond strength and, thus, MHHPA is considered to be a more effective hardener than ADH for low temperature snap cure NCPs.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2001.11a
• /
• pp.146-150
• /
• 2001

Microwave model and high-frequency measurement of the ACF flip-chip interconnection was investigated using a microwave network analysis. S-parameters of on-chip and substrate were separately measured in the frequency range of 200 MHz to 20 GHz using a microwave network analyzer HP8510 and cascade probe. And the cascade transmission matrix conversion was performed. The same measurements and conversion techniques were conducted on the assembled test chip and substrate at the same frequency range. Then impedance values in ACF flip-chip interconnection were extracted from cascade transmission matrix. ACF flip chip interconnection has only below 0.1nH, and very stable up to 13 GHz. Over the 13 GHz, there was significant loss because of epoxy capacitance of ACF. However, the addition of SiO$_2$filler to the ACF lowered the dielectric constant of the ACF materials resulting in an increase of resonance frequency up to 15 GHz. High frequency behavior of metal Au stud bumps was investigated. The resonance frequency of the metal stud bump interconnects is higher than that of ACF flip-chip interconnects and is not observed at the microwave frequency band. The extracted model parameters of adhesive flip chip interconnects were analyzed with the considerations of the characteristics of material and the design guideline of ACA flip chip for high frequency applications was provided.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.223-226
• /
• 2007

본 연구에서는 Ag anisotropic conductive adhesive(ACA)의 종류, 경화 조건 및 안테나 패턴의 재질에 따른 flip chip bonding된 RFID die의 접합부 신뢰성이 조사되었다. 접합강도 측정에 의하여 접합강도가 최적화되는 공정 시간을 결정할 수 있었으며, 그러한 최적의 공정조건에서는 paste-type Ag ink로 인쇄된 안테나 상에서의 RFID die의 접합강도가 Cu 재질 안테나에 비해 상대적으로 높게 측정됨을 알 수 있었다. RFID tag의 인식거리 측정 시험을 통하여 적절한 경화 조건이 적용된다면 안테나의 재질이 인식거리 변화에 가장 주요한 영향을 미치는 인자임을 알 수 있었다. 아울러 Cu 안테나 패턴은 RFID die의 접합 과정에서 곡률을 가지며 휘어지면서 인식거리와 관련된 long-tem reliability를 악화시킬 수 있음을 관찰할 수 있었다.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.1
• /
• pp.17-24
• /
• 2012

Recently, flip chip interconnection has been increasingly used in microelectronic assemblies. The common Flip chip interconnection is formed by reflow of the solder bumps. Lead-Tin solders and Tin-based solders are most widely used for the solder bump materials. However, the flip chip interconnection using these solder materials cannot be applied to temperature-sensitive components since solder reflow is performed at relatively high temperature. Therefore the development of low temperature bonding technologies is required in these applications. A few bonding techniques at low temperature of $150^{\circ}C$ or below have been reported. They include the reflow soldering using low melting point solder bumps, the transient liquid phase bonding by inter-diffusion between two solders, and the bonding using low temperature curable adhesive. This paper reviews various low temperature bonding methods.