• Journal of Welding and Joining
• /
• v.25 no.3
• /
• pp.45-50
• /
• 2007

The present study is devoted to investigate the transient flow and to estimate the filling time fur underfill process by using the numerical model established on the fluid momentum equation. For optimization of the design and selection of process parameters, this study extensively presents an estimation of the filling time in the view points of some important factors related to underfill materials and flip-chip geometry. From the results, we conclude that the filling time changes with respect to the under fill materials because of different viscosity, surface tension coefficient and contact angle. It reveals that, as the gap height increases, the filling time decreases substantially, and goes to the saturated values.

• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.3
• /
• pp.21-27
• /
• 2007

Nickel bumps for ACF(anisotropic conductive film) flip chip application were fabricated by electroless and electro plating and their mechanical properties and impact reliability were examined through the compressive test, bump shear test and drop test. Stress-displacement curves were obtained from the load-displacement data in the compressive test using nano-indenter. Electroplated nickel bumps showed much lower elastic stress limits (70MPa) and elastic moduli ($7.8{\times}10^{-4}MPa/nm$) than electroless plated nickel bumps ($600-800MPa,\;9.7{\times}10^{-3}MPa/nm$). In the bump shear test, the electroless plated nickel bumps were deformed little by the test blade and bounded off from the pad at a low shear load, whereas the electroplated nickel bumps allowed large amount of plastic deformation and higher shear load. Both electroless and electro plated nickel bumps bonded by ACF flip chip method showed high impact reliability in the drop impact test.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.9
• /
• pp.798-802
• /
• 2005

The plating shape in the opening of photoresist becomes gradated shape in the fountain plating system, because bubbles from the wafer surface are difficult to escape from the deep openings, vias. In this paper, the bubble flow from the wafer surface during plating process was studied and we designed the tilted electrode ring to get uniform bump height on all over the wafer and evaluated the film uniformity by SEM and $\alpha-step$. In a-step measurement, film uniformities in the fountain plating system and the tilted electrode ring contact system were $\pm16.6\%,\;\pm4\%$ respectively.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.1005-1008
• /
• 2003

We report a new FCOG (flip chip on glass) technique using solder bumps for display packaging applications. The In and Sn solder bumps of 40 ${\mu}m$ pitches were formed on Si and glass substrate. The In and Sn bumps were bonded at 125 at the pressure of 3 mN/bump. The metallurgical bonding was confirmed using cross-sectional SEM. The contact resistance of the solder joint was 65 $m{\Omega}$ which was much lower than that of the joint made using the conventional ACF bonding technique. We demonstrate that the new COG technique using solder bump to bump direct bonding can be applied to advanced LCDs that lead to require higher quality, better resolution, and lower power consumption.

• Journal of the Microelectronics and Packaging Society
• /
• v.5 no.1
• /
• pp.7-18
• /
• 1998

In the flip chip interconnection on organic substrates using eutectic Pb/Sn solder bumps highly reliable Under Bump Metallurgy (UBM) is required to maintain adhesion and solder wettability. Various UBM systems such as 1$\mu$m Al/0.2$\mu$m Pd/1$\mu$m Cu, laid under eutectic Pb/Sn solder were investigated with regard to their interfacial reactions and adhesion proper-ties. The effects of numbers of solder reflow and aging time on the growth of intermetallic compounds (IMCs) and on the solder ball shear strength were investigated. Good ball shear strength was obtained with 1$\mu$m Al/0.2$\mu$m Ti/5$\mu$m Cu and 1$\mu$m Al/0.2$\mu$m ni/1$\mu$m Cu even after 4 solder reflows or 7 day aging at 15$0^{\circ}C$. In contrast 1$\mu$m Al/0.2$\mu$m Ti/1$\mu$m Cu and 1$\mu$mAl/0.2$\mu$m Pd/1$\mu$m 쳐 show poor ball shear strength. The decrease of the shear strength was mainly due to the direct contact between solder and nonwettable metal such as Ti and Al resulting in a delamination. In this case thin 1$\mu$m Cu and 0.2$\mu$m Pd diffusion barrier layer were completely consumed by Cu-Sn and pd-Sn reaction.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.2
• /
• pp.31-43
• /
• 2019

In this study, polymer elastic bumps were fabricated for the flexible electronic package flip chip bonding and the viscoelastic and viscoplastic behavior of the polymer elastic bumps according to the temperature and load were analyzed using FEM and experiments. The polymer elastic bump is easy to deform by the bonding load, and it is confirmed that the bump height flatness problem is easily compensated and the stress concentration on thin chip is reduced remarkably. We also develop a spiral cap type and spoke cap type polymer elastic bump of $200{\mu}m$ diameter to complement Au metal cap crack phenomenon caused by excessive deformation of polymer elastic bump. The proposed polymer elastic bumps could reduce stress of metal wiring during bump deformation compared to metal cap bump, which is completely covered with metal wiring because the metal wiring on these bumps is partially patterned and easily deformable pattern. The spoke cap bump shows the lowest stress concentration in the metal wiring while maintaining the low contact resistance because the contact area between bump and pad was wider than that of the spiral cap bump.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.9
• /
• pp.1-5
• /
• 1999

In this paper, we proposed a novel branch-line coupler using filp-chip technology. The proposed coupler consists of CPW and inverted microstrip. The CPW is on the GaAs flip-chip substrate, and the inverted microstrip is on the alumina main substrate. The ground plane of the CPW is used as a ground plane of the inverted microstrip. And both the transmission lines are connected by solder bump with each other. The characteristics of thisstructure was calculated by FDTD method. The S21, S31 are -3dB and the phase difference is $90^{\circ}$. The calculated characteristics are the same as those of the regular branch-line coupler. This structure can be applied for various kinds of devices using flipchip technology.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.2
• /
• pp.55-61
• /
• 2010

The device with tantalum silicide heater were bonded by Ag paste and Au SBB(Stud Bump Bonding) onto the Au coated substrate. The shear test after Au ABB and the thermal performance under current stressing were measured. The optimum condition of Au SBB was determined by fractured surface after die shear test and $350^{\circ}C$ for substrate, $250^{\circ}C$ for die during flip chip bonding with bonding load of about 300 g/bump. With applying 5W through heater on the device, the maximum temperature with Ag paste bonding was about $50^{\circ}C$. That with Au SBB on Au coated Si substrate showed $64^{\circ}C$. The difference of maximum temperatures is only $14^{\circ}C$, even though the difference of contact area between Ag paste bonding and Au SBB is by about 300 times and the simulation showed that the contact resistance might be one of the reasons.

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.4
• /
• pp.19-25
• /
• 2011

The size reduction of the semiconductor chip and the improvement of the electrical performance have been enabled through the introduction of the Cu/Low-K process in modern electronic industries. However, Cu/Low-K has a disadvantage of the physical properties that is weaker than materials used for existing semiconductor manufacture process. It causes many problems in chip manufacturing and package processes. Especially, the delamination between the Cu layer and the low-K dielectric layer is a main defect after the temperature cycles. Since the Cu/Low-K layer is located on the top of the pad of the flip chip, the stress on the flip chip affects the Cu/Low-K layer directly. Therefore, it is needed to improve the underfill process or materials. Especially, it becomes very important to select the underfill to decrease the stress at the flip-chip and to protect the solder bump. We have solved the delamination problem in a 90 nm Cu/Low-K flip-chip package after the temperature cycle by selecting an appropriate underfill.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.3
• /
• pp.267-271
• /
• 2004

The joint strength and fracture surface of Sn-Pb solder bump in photo diode packages after isothermal aging testing were studied experimentally. Cu/Sn-Pb solders were adopted, and aged for up to 900 hours at 12$0^{\circ}C$ and 17$0^{\circ}C$ to analyze the effect of intermetallic compound(IMC). In 900-hour aging experiments, the maximum shea strength of Sn-Pb solder decreased by 20％ and 9％. The diffraction patterns of Cu$_{6}$Sn$_{5}$, scallop-shape IMC, and planar-shape Cu$_3$Sn were observed by Transmission Electron Microscopy (TEM).EM).