• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1997년도 가을 학술발표회 논문집
• /
• pp.80-86
• /
• 1997

Recently, the box-girder bridge became quite popular because of the effectiveness of the box section against torsional deformation, and the finite element method has been one of the powerful and versatile method for obtaining the solution of box-girder bridge. The finite element method is used to solve a box girder which is built up with flat plates such as flanges, webs and diaphragm, and box girder is idealized by 8-nodes 2-dimensional isoparmetric finite element. To investigate the stress of diaphragm, substructure analysis is performed with two Parameters which are the location of support and slope of web.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.323-327
• /
• 2009

Silicone is recently used for LED chip encapsulment due to its good thermal stability and optical transmittance. In order to predict residual stress which causes optical briefringence and mechanical warpage of silicone, finite element analysis was conducted for both curing and cooling process during silicone molding. For analysis of curing process, a cure kinetics model was derived based on the differential scanning calorimetry(DSC) test and applied to the material properties for finite element analysis. Finite element simulation result showed that the curing as well as the cooling process should be designed carefully so as to reduce the residual stress although the cooling process plays the bigger role than curing process in determining the final residual stress state.

• 한국CDE학회논문집
• /
• 제21권4호
• /
• pp.426-432
• /
• 2016

Designing a morphologically well-fitted hip implant to a patient anatomy is desirable to improve surgical outcomes since a commercial ready-made hip implant may not well conform to the patient joint. In this study, biomechanical stability of patient-specific hip implants with two different stem lengths was compared and discussed using a 3D finite element analysis (FEA). The FEA results in this study showed that an increase in stem length brings about more the peaked von-Mises stress (PVMS) in the prosthesis and less in the femur. However the decrease in von-Mises stress in the femur causes stress shielding phenomenon that usually leads to considerable bone resorption. Although, in biomechanical stability point of view, this work recommends the use of smaller stems, the length of stem must be determined by considering both the von-Mises stress and the stress-shielding phenomenon.

• 한국정밀공학회지
• /
• 제26권11호
• /
• pp.85-91
• /
• 2009

A lip seal is widely used not only to prevent leakage of fluids from an actuator or a rotating shaft but also to exclude outside substances. Recently, TPU(Thermoplastic Polyurethane), which is one of the sealing materials, has been frequently used due to its excellent mechanical properties and wear resistance. The material constants for finite element analysis through the experiment on stress relaxation are presented. The reaction forces of a shaft as well as the contact pressures of a lip seal under condition before and after stress relaxation using finite element analysis were obtained, The results show that stress relaxation has not a little effect on the performance of a lip seal.

• 대한기계학회논문집
• /
• 제14권3호
• /
• pp.547-553
• /
• 1990

본 연구에서는 알루미나 세라믹(Al$_{2}$O$_{3}$)재료와 순수구리를 티타늄 용자재로써 접합한 브레이징 접합물내의 냉각후 잔류응력을 유한요소법으로 사용하여 해석하였다.

• 한국압력기기공학회 논문집
• /
• 제19권2호
• /
• pp.75-83
• /
• 2023

For three-dimensional finite element welding residual stress simulation, several methods are available. Two widely used methods are the moving heat source model using heat flux and the temperature boundary condition model using the temperature profile of the welded beads. However, each model has pros and cons in terms of calculation times and difficulties in determining welding parameters. In this paper, a new method using the moving temperature profile model is proposed to perform efficiently 3-D FE welding residual stress analysis for large structures. Comparison with existing experimental residual stress measurement data of two-pass welding pipe and SNL(Sandia National Laboratories) mock-up canister shows the accuracy and efficiency of the proposed method.

• 한국전산구조공학회논문집
• /
• 제31권4호
• /
• pp.199-206
• /
• 2018

범용유한요소프로그램인 Abaqus의 확장유한요소법(XFEM)의 사용성 검증을 위하여 2차원 모델에 적용하여 수치해석을 수행하였다. 기존의 연구에 많이 사용되었던 응집요소(cohesive element) 모델은 균열 경로를 예측하고 요소를 삽입하여야 하는 단점 때문에 실제 균열을 모사하는데 한계가 있다. 이러한 이유로 응력의 방향성 및 특이성을 바탕으로 균열의 경로를 예측하는 확장유한요소법(XFEM)이 균열 해석에 있어서 더 발전된 방법으로 이용되어 왔다. 이번 연구에서는 균열의 경로가 자명한 2차원 모델에 사용하여 응집요소해석과 XFEM에 응집요소의 물성을 적용한 해석을 비교하고 XFEM 적용의 타당성을 확인하였다. 수치해석으로 균열 발생 직전의 응력분포 및 응력 특이성을 확인하고 실제 균열 발생경로와의 비교를 한다. 본 연구를 바탕으로 몇 가지의 한계를 극복하면 실제 복잡한 모델의 실제 균열진전해석을 수행하여 균열을 모사할 수 있을 것으로 기대된다.

• The Journal of Advanced Prosthodontics
• /
• 제13권6호
• /
• pp.396-407
• /
• 2021

PURPOSE. Zirconia has exceptional biocompatibility and good mechanical properties in clinical situations. However, finite element analysis (FEA) studies on the biomechanical stability of two-piece zirconia implant systems are limited. Therefore, the aim of this study was to compare the biomechanical properties of the two-piece zirconia and titanium implants using FEA. MATERIALS AND METHODS. Two groups of finite element (FE) models, the zirconia (Zircon) and titanium (Titan) models, were generated for the exam. Oblique (175 N) and vertical (175 N) loads were applied to the FE model generated for FEA simulation, and the stress levels and distributions were investigated. RESULTS. In oblique loading, von Mises stress values were the highest in the abutment of the Zircon model. The von Mises stress values of the Titan model for the abutment screw and implant fixture were slightly higher than those of the Zircon model. Minimum principal stress in the cortical bone was higher in the Titan model than Zircon model under oblique and vertical loading. Under both vertical and oblique loads, stress concentrations in the implant components and bone occurred in the same area. Because the material itself has high stiffness and elastic modulus, the Zircon model exhibited a higher von Mises stress value in the abutments than the Titan model, but at a level lower than the fracture strength of the material. CONCLUSION. Owing to the good esthetics and stress controllability of the Zircon model, it can be considered for clinical use.

• 대한기계학회논문집A
• /
• 제35권1호
• /
• pp.25-31
• /
• 2011

인장시험할 때 최대하중점을 넘으며 네킹이 발생하여 단면에 분포하는 응력이 더 이상 균일하지 않다. 네킹이 진행될수록 상당응력은 축방향 응력과 더 달라진다. 이 네킹현상을 극복하고 진응력-진변형도 곡선을 결정하는 방법이 이제까지 많이 연구개발되었다. 그 중에서 유한요소해석 시뮬레이션을 이용하는 방법이 매력적이다. 이 논문에서는 범용상용 프로그램을 사용하여 인장시험을 시뮬레이션하였다. 같은 강괴에서 채취한 봉상시편과 판상시편을 인장시험하고 시뮬레이션하였다. Hollomon 법칙을 가정하지 않고 진응력-진변형도 곡선을 결정하였다.

• 한국정밀공학회지
• /
• 제19권2호
• /
• pp.171-176
• /
• 2002

This paper is the study on stress analysis of spur gear using a finite element method. Gear drives constitute very important mechanisms in transmitting mechanical power processes compromising several cost effective and engineering advantages. The load transmission occurred by the contacting surfaces arises variable elastic deformations which are being evaluated through finite element analysis. The automatic gear design program is developed to model gear shape precisely. This gear design system developed was used by pre-processor of FEM packages. The distribution of stresses at contacting surfaces was examined when a pair of gear contact.