• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.866-873
• /
• 2009

CFRD (Concrete Faced Rockfill Dam) has been world-widely constructed due to a lot of advantages compared with rockfill dam and recently, sand/gravel materials, instead of crushed rock materials, are also utilized as a main rockfill material to overcome geological and environmental problems. In this paper, the process of water infiltration into the originally unsaturated sand/gravel-fill dam is studied using two-dimensional saturated-unsaturated seepage theory. According to the results of seepage analysis, if the effective drainage zone is installed in the dam, the reservoir water infiltrate into the dam along a downward flow path towards the lower drainage area. The main body constructed with sand/gravel materials, therefore, remains unsaturated.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.489-493
• /
• 2001

Big cities in Japan have serious problems due to the shortage of new reclaimed land for municipal wastes. If harmful heavy metals such as cadmium, lead, copper and etc. are contained in the municipal waste combustion residues, they are not able to fill up according to the environmental law in Japan. In this study, the removal of heavy metals in the fly ash (EP ash) was dealt with chloridizing vaporization method. EP ash as a non-hazardous materials is utilized as covering materials, road bed, and building materials.

• Korean Journal of Materials Research
• /
• v.27 no.10
• /
• pp.518-523
• /
• 2017

In commercial solar cells, the pattern of the front electrode is critical to effectively assemble the photo generated current. The power loss in solar cells caused by the front electrode was categorized as four types. First, losses due to the metallic resistance of the electrode. Second, losses due to the contact resistance of the electrode and emitter. Third, losses due to the emitter resistance when current flows through the emitter. Fourth, losses due to the shading effect of the front metal electrode, which has a high reflectance. In this paper, optimizing the number of finger on a $4{\times}4$ solar cell is demonstrated with known theory. We compared the short circuit current density and fill factor to evaluate the power loss from the front metal contact calculation result. By experiment, the short circuit current density($J_{sc}$), taken in each pattern as 37.61, 37.53, and $37.38mA/cm^2$ decreased as the number of fingers increased. The fill factor(FF), measured in each pattern as 0.7745, 0.7782 and 0.7843 increased as number of fingers increased. The results suggested that the efficiency(Eff) was measured in each pattern as 17.51, 17.81, and 17.84 %. Throughout this study, the short-circuit current densities($J_{sc}$) and fill factor(FF) varied according to the number of fingers in the front metal pattern. The effects on the efficiency of the two factors were also investigated.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.185-192
• /
• 2000

Recently, the hydraulic fill method is commonly used in many reclamation projects due to lack of fill materials. The method of hydraulic fill in reclamation is executed by transporting the mixture of water-soil particles into a reclaimed land through dredging pipes, then the dredged soil particles settle down in the water or flow over an out flow weir with the water. In the present study, practice each three method in order to suggest method of determining the loss rate of the dredged fills. The first sieve and hydrometer analysis were performed with the soil samples obtained before and after dredging and then apply theory of particle breakage, the second compare with the volume of dredged soil between at the dredging area and the target pond and the last compare with weight of dredged soil between before and after dredging at the dredging area and in the target pond for estimating the amount of soil particles residual at the reclaimed area and the loss of soil particles passed through the weir. In addition to compare with the loss ratio between as using Marsal's modified theory of particle breakage and measured weight and volume in the field.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.10a
• /
• pp.665-672
• /
• 2002

In order to expand agricultural lands in the western and southern coasts of Korean Peninsula, coarse soils excavated from hillsides have been used as fill materials for reclamation. In order to tackle with the problems and to confirm availability, research on soil improvement involve mixing cement to the fine wet soils. Required undrained shear strength(c$\sub$u/) for fill material was analyzed to be 0.34∼1.2kg/$\textrm{cm}^2$. It has been known that when cement is added to high water content marine clay, its unconfined compression strength increased to 2kg/$\textrm{cm}^2$. Consolidation results show that pre-consolidation pressure increased to 1.8kg/$\textrm{cm}^2$ and 3.4kg/$\textrm{cm}^2$ with the addition of 3% and 5% of cement respectively. This result shows that low-height embankments could be constructed without significant compression. Since the effectiveness of improvement may be different site by site, the mix design for each site is necessary in order to optimize it. The process is first to determine aimed shear strength and then optimum mix ratio of cement after carrying out a series of tests.

• Restorative Dentistry and Endodontics
• /
• v.48 no.3
• /
• pp.30.1-30.11
• /
• 2023

Objectives: This study verified the possibility of cementing fiberglass-reinforced posts using a flowable bulk-fill composite (BF), comparing its push-out bond strength and microhardness with these properties of 3 luting materials. Materials and Methods: Sixty endodontically treated bovine roots were used. Posts were cemented using conventional dual-cured cement (CC); self-adhesive cement (SA); dual-cured composite (RC); and BF. Push-out bond strength (n = 10) and microhardness (n = 5) tests were performed after 1 week and 4 months of storage. Two-way repeated measures analysis of variance (ANOVA), 1-way ANOVA, t-test, and Tukey post-hoc tests were applied for the push-out bond strength and microhardness results; and Pearson correlation test was applied to verify the correlation between push-out bond strength and microhardness results (α = 0.05). Results: BF presented higher push-out bond strength than CC and SA in the cervical third before aging (p < 0.01). No differences were found between push-out bond strength before and after aging for all the luting materials (p = 0.84). Regarding hardness, only SA presented higher values measured before than after aging (p < 0.01). RC and BF did not present 80% of the maximum hardness at the apical regions. A strong positive correlation was found between the luting materials' push-out bond strength and microhardness (p < 0.01, R² = 0.7912). Conclusions: The BF presented comparable or higher push-out bond strength and microhardness than the luting materials, which indicates that it could be used for cementing resin posts in situations where adequate light curing is possible.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.3 no.2
• /
• pp.69-75
• /
• 2003

Cell transistor and data retention time characteristics were studied in 90 nm design rule 512M-bit DRAM, for the first time. And, the characteristics of cell transistor are investigated for different STI gap-fill materials. HDP oxide with high compressive stress increases the threshold voltage of cell transistor, whereas the P-SOG oxide with small stress decreases the threshold voltage of cell transistor. Stress between silicon and gap-fill oxide material is found to be the major cause of the shift of the cell transistor threshold voltage. If high stress material is used for STI gap fill, channel-doping concentration can be reduced, so that cell junction leakage current is decreased and data retention time is increased.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.8
• /
• pp.95-106
• /
• 2009

This study was intended to identify the effect of the wetting on a long-term compression settlement of the rock/soil mixture used as fill material, depending on compaction and grading conditions. The relatively large settlement happened under the fully-submerged condition, and a repeated settlement was monitored when moisture content increased over and over again like the rainfall infiltration. In case of the materials without fine fractions or compacted in wet condition, the settlement caused by wetting was relatively low. In conclusion, the long-term compression settlement of granular (rock/soil mixture) fill material is more affected by the increase of water content and temperature change (freezing and thawing) than creep.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.10
• /
• pp.105-111
• /
• 2008

To improve the stability of levee structure, it is required to use good quality fill materials, intensive management, appropriate hydraulic structure and construction of cut-off wall. In particular, the most important factor of levee construction technology is to use bed sediment for its safety. In this study, seepage model test and numerical analysis were performed based on a standard section of levee recommended in the river design standard of korea (2005). The results of test and analysis show that most of the bed soil is a sand (SP in USCS), which does not satisfy the permeability criteria for levee materials ($< k=10^{-3}cm/sec$), thus for the safety of levee it is required to adopt a stabilizing method such as good quality soil mixing, water content control.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1497-1500
• /
• 2006

Inkjet printing technology can reduce the LCD color filter manufacturing cost more than 50 %. Uniform color filter patterning can be achieved only with proper ink and barrier materials. We developed new ink and black matrix materials for inkjet color filter. The ink materials have low volatility while they have very high solid content. The black matrix materials have very precisely controlled surface energy so that the inks can fill the pixels evenly and completely. We controlled the ink drop volume and ink material to minimize the thickness difference between the black matrix and the color pixel. Micron-order jetting position accuracy was achieved. We successfully printed 14.1" color filters using our ink and black matrix materials.