• Journal of the Korean Society for Heat Treatment
• /
• v.28 no.6
• /
• pp.310-314
• /
• 2015

We have considered the influence of electron irradiation on the optical and electrical properties of $In_2O_3/Ti$ bi-layered films prepared with RF and DC magnetron sputtering. The $In_2O_3/Ti$ thin films irradiated at 600 eV shows the lowest resistivity of $6.9{\times}10^{-4}{\Omega}cm$. The optical transmittance in a visible wave length region also influenced with the electron irradiation energy. The film that electron irradiated at 600 eV shows 82.9% of optical transmittance in this study. By comparison of figure of merit, it is concluded that the opto-electrical performance of $In_2O_3/Ti$ bi-layered film is improved with electron irradiation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.5
• /
• pp.500-506
• /
• 2024

The transparent electrode characteristics of the SnO₂/AgNi/SnO₂ (OMO) multilayer structures prepared by sputtering were investigated according to the annealing temperature. Ni-doped Ag of various compositions was selected as the metal layer and heat treatment was performed at 100~300℃ to evaluate the thermal stability of the metals. The manufactured OMO multilayer structures were heat treated for 6 hours at 400~600℃ in an N₂ atmosphere. The structural, electrical, and optical properties of the OMO structures before and after annealing were evaluated and analyzed using a UV-VIS spectrophotometer, 4-point probe, XPS, FE-SEM, etc. OMO with Ni-doped Ag shows improved performance due to the reduction of structural defects of Ag during annealing, but OMO structure with pure Ag shows degradation characteristics due to Ag diffusion into the oxide layer during high-temperature annealing. The figure of merit (FOM) of SnO₂/Ag/SnO₂ was highest at room temperature and gradually decreased as the heat treatment temperature increased. On the other hand, the FOM value of SnO₂/AgNi/SnO₂ mostly showed its maximum value at high temperature(~550℃). In particular, the FOM value of SnO₂/Ag-Ni (3.2 at%)/SnO₂ was estimated to be approximately 2.38×10^-2 Ω^-1. Compared to transparent electrodes made of other similar materials, the FOM value of the SnO₂/Ag-Ni (3.2 at%)/SnO₂ multilayer structure is competitive and is expected to be used as an alternative transparent conductive electrode in various devices.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.2
• /
• pp.47-52
• /
• 2017

In this paper, CMOS SAR A/D converter 1.8V supply for the design of an A/D converter having an middle speed for the biological signal processing was designed. This paper proposes design of a 10-bit SAR Analog to Digital Converter improving linearity driven by MSB node of C-DAC array divided into 4 equal parts. It enhances linearity property, by retaining the analog input signal charging time at MSB node. Because MSB node samples analog input, it enhances resolution through getting initial input signal precisely. By using split capacitor on C-DAC array, it reduced chip size and power dissipation. The Proposed SAR A/D Converter is fabricated in 0.18um CMOS and measured 7.5 bits of ENOB at sampling frequency 4MS/s and power supply of 1.8V. It occupies a core area of $850{\times}650um^2$ and consumes 123.105uW. Therefore it results in 170.016fJ/step of FOM(Figure of Merit).

• Journal of the Korean Society for Heat Treatment
• /
• v.30 no.1
• /
• pp.13-16
• /
• 2017

$SnO_2$ single layer films and 2 nm thick Ni thin film intermediated $AZO/Ni/SnO_2$ trilayer films were deposited on glass substrate at room temperatures by RF and DC magnetron sputtering and then the optical and electrical properties of the films were investigated to enhance opto-electrical performance of $SnO_2$ single layer films. As deposited $SnO_2$ films show the optical transmittance of 81.8% in the visible wavelength region and a resistivity of $1.2{\times}10^{-2}{\Omega}cm$, while $AZO/Ni/SnO_2$ films show a lower resistivity of $5.8{\times}10^{-3}{\Omega}cm$ and an optical transmittance of 77.1% in this study. Since $AZO/Ni/SnO_2$ films show the higher figure of merit than that of the $SnO_2$ single layer films, it is supposed that the $AZO/Ni/SnO_2$ films can assure high opto-electrical performance for use as a transparent conducting oxide in various display applications.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.2
• /
• pp.49-54
• /
• 2010

The n-type $Bi_2(Te,Se)_3$ powders were fabricated by melting/grinding method and were hot-pressed in order to compare thermoelectric properties of the hot-pressed specimens with those of the $Bi_2(Te,Se)_3$ ingot. Effects of mechanical milling treatment of the $Bi_2(Te,Se)_3$ powders on thermoelectric characteristics of a hot-pressed specimen were also examined. The hot-pressed $Bi_2(Te,Se)_3$ exhibited power factors of $27.3{\sim}32.3{\times}10^{-4}W/m-K^2$ which were superior to $24.2{\times}10^{-4}W/m-K^2$ of the ingot. The $Bi_2(Te,Se)_3$, hot-pressed after mechanical milling treatment of the powders, possessed a non-dimensional figure-of-merit of 1.02 at $100^{\circ}C$ and exhibited extrinsic-intrinsic transition at $130^{\circ}C$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.8
• /
• pp.64-72
• /
• 2010

This paper presents a wide range VCO with fine coarse tuning step using a sigma-delta modulation technique for UWB frequency synthesizer. The proposed coarse tuning scheme provides the low effective frequency resolution without any degradation of phase noise performance. With three steps coarse tuning, the VCO has wide tuning range and fine tuning step simultaneously. The frequency synthesizer with VCO was implemented with 0.13 ${\mu}m$ CMOS technology. The tuning range of the VCO is 5.8 GHz~6.8 GHz with the effective frequency resolution of 3.9 kHz. It achieves the measured phase noise of -108 dBc/Hz at 1 MHz offset and a tuning range 16.8 % with 5.9 mW power. The figure-of-merit with the tuning range is -181.5 dBc/Hz.

• Korean Journal of Materials Research
• /
• v.16 no.10
• /
• pp.647-651
• /
• 2006

A new class of compounds in the form of skutterudite structure, Fe doped $CoSb_3$ with a nominal composition of $Fe_xCo_{4-x}Sb_{12}$ ($0{\leq}x{\leq}2.5$), were synthesized by mechanical alloying of elemental powders followed by vacuum hot pressing. Nanostructured, single-phase skutterudites were successfully produced by vacuum hot pressing using as-milled powders without subsequent heat-treatments for the compositions of $x{\leq}1.5$. However, second phase was found to form in case of $x{\geq}2$, suggesting the solubility limit of Fe with Co in this system. Thermoelectric properties including thermal conductivity from 300 to 600 K were measured and discussed. Lattice thermal conductivity was greatly reduced by introducing a dopant up to x=1.5 as well as by increasing phonon scattering in nanostructured skutterudite, leading to enhancement in the thermoelectric figure of merit. The maximum figure of merit was found to be 0.32 at 600 K in the composition of $Fe_xCo_{4-x}Sb_{12}$.

• Journal of IKEEE
• /
• v.26 no.4
• /
• pp.728-735
• /
• 2022

In this work, we investigated a high-voltage (~4.5 kV) 4H-SiC power DMOSFET with modifications of current spreading layer (CSL), which was introduced below the p-well region for low on-resistance. These include the following: 1) a thickness of CSL (T_CSL) from 0 um to 0.9 um; 2) a doping concentration of CSL (N_CSL) from 1×10¹⁶ cm^-3 to 5×10¹⁶ cm^-3. The design is optimized using TCAD 2D-simulation, and we found that CSL helps to reduce specific on-resistance but also breakdown voltage. The resulting structures exhibit a specific on-resistance (R_on,sp) of 59.61 mΩ·cm², a breakdown voltage (V_B) of 5 kV, and a Baliga's Figure of Merit (BFOM) of 0.43 GW/cm².

• Korean Journal of Materials Research
• /
• v.34 no.1
• /
• pp.55-62
• /
• 2024

Fluorine-doped tin oxide (FTO) has been used as a representative transparent conductive oxide (TCO) in various optoelectronic applications, including light emitting diodes, solar cells, photo-detectors, and electrochromic devices. The FTO plays an important role in providing electron transfer between active layers and external circuits while maintaining high transmittance in the devices. Herein, we report the effects of substrate rotation speed on the electrical and optical properties of FTO films during ultrasonic spray pyrolysis deposition (USPD). The substrate rotation speeds were adjusted to 2, 6, 10, and 14 rpm. As the substrate rotation speed increased from 2 to 14 rpm, the FTO films exhibited different film morphologies, including crystallite size, surface roughness, crystal texture, and film thickness. This FTO film engineering can be attributed to the variable nucleation and growth behaviors of FTO crystallites according to substrate rotation speeds during USPD. Among the FTO films with different substrate rotation speeds, the FTO film fabricated at 6 rpm showed the best optimized TCO characteristics when considering both electrical (sheet resistance of 13.73 Ω/□) and optical (average transmittance of 86.76 % at 400~700 nm) properties with a figure of merit (0.018 Ω^-1).

• Journal of IKEEE
• /
• v.20 no.2
• /
• pp.181-183
• /
• 2016

In this work, the merged PiN Schottky(MPS) diodes based silicon carbide(SiC) have been optimized and designed for 1200V diodes by 2D-atlas simulation tool. We investigated the optimized characteristics of SiC MPS diodes such as breakdown voltage and specific on-resistance by varying the doping concentrations of P-Grid/epi-layer and space of P-Grid, which are the most important parameters. The breakdown voltage and specific on-resistance, based on Baliga's Figure Of Merit (BFOM), have been compared with and the SiC-based MPS diodes show improved BFOMs with low values of specific on-resistance and high breakdown voltage. It has been demonstrated 1,200 V SiC MPS diodes will find useful applications in high voltage energy-efficient devices.