• Journal of the Earthquake Engineering Society of Korea
• /
• v.10 no.4 s.50
• /
• pp.85-94
• /
• 2006

In the design of bridge piers in seismic area, the ductility requirement is the most important factor. In order to enhance the seismic performance of RC columns, it is necessary to make the ductility of columns larger by covering RC columns with steel tubes or confining RC columns by arranging transverse reinforcements such as hoop ties closely. Using core steel composite columns is useful as one of the reinforcing RC columns. In this paper, quasi-static tests on concrete encased composite columns with single core steel or multiple steel elements were performed to investigate the seismic performance of the composite columns. Eight concrete-encased composite specimens were fabricated. The cross-sections of these specimens are composed of concrete-encased H-shaped structural steel columns and a concrete-encased circular tube with partial in-filled concrete. Test parameters were the amount of the transverse reinforcements, type and number of encased steel member. Through the tests, it was evaluated the ductility of SRC composite specimens. It has become clear from the test results that encased steel elements makes the deformation capacity of the columns to be larger. The displacement ductility and lateral strength of specimen with concrete-encased circular tube were indicated the biggest value.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.5 s.335
• /
• pp.15-22
• /
• 2005

This paper proposes an efficient structure which is able to perform self-detection and self-repair for faults in a digital system by imitating the structure of living beings. The self-repair system is composed of artificial cells, which have homogeneous structures in the two-dimension, and spare cells. An artificial cell is composed of a logic block based on multiplexers, and a genome block, which controls the logic block. The cell is designed using DCVSL (differential cascode voltage switch logic) structure to self-detect faults. If a fault occurs in an artificial cell, it is self-detected by the DCVSL. Then the artificial cells which belong to the column are disabled and reconfigured using both neighbour cells and spare cells to be repaired. A self-repairable 2-bit up/down counter has been fabricated using Hynix $0.35{\mu}m$ technology with $1.14{\times}0.99mm^2$ core area and verified through the circuit simulation and chip test.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.2
• /
• pp.111-116
• /
• 2003

In this paper, a CMOS baseband analog receiver for wireless home network is discussed. It is composed of a Gilbert type mixer, an Elliptic 6th order 1ow pass filter, and a 6-bit A/D converter. The main role of the mixer is generating a mixed analog signal between the 200MHz output signal of CMOS RF stage and the 199MHz local oscillator. After the undesired high frequency component of the mixed signal comes out. Finally, the analog signal is converted into digital code at the 6-bit A/D converter, The proposed receiver is fabricated with 0.25${\mu}{\textrm}{m}$ 1-poly 5-metal CMOS technology, and the chip area is 200${\mu}{\textrm}{m}$ X1400${\mu}{\textrm}{m}$. the receiver consumes 130㎽ at 2.5V power supply.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.9
• /
• pp.11-17
• /
• 2004

This paper describes the implementation of monolithic optical transceiver circuitry being used as a part of the fiber optic modules. It has been fabricated in 0.6 ${\mu}{\textrm}{m}$ 2-poly 3-metal silicon CMOS analog technology and operates at 155.52 Mbps(STM-1) data rates. It drives laser diode to transmit intensity modulated optical signal according to 155.52 Mbps electrical data from system. Also, it receives 155.52 Mbps optical data that transmitted from other systems and converts it to electrical data using photo diode and amplifier. To avoid noise and interference between transmitter and receiver on one chip, layout techniques such as special placement, power supply separation, guard ring, and protection wall were used in the design. The die area is 4 ${\times}$ 4 $\textrm{mm}^2$, and it has 32.3 ps rms and 335.9 ps peak to peak jitter on loopback testing. the measured power dissipation of whole chip is 1.15 W(230 mW) with a single 5 V supply.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.11
• /
• pp.13-20
• /
• 2008

In this paper, an 1.8V 12-bit 10MSPS CMOS A/D converter (ADC) is described. The architecture of the proposed ADC is based on a folding and interpolation using an even folding technique. For the purpose of improving SNR, cascaded-folding cascaded-interpolation technique, distributed track and hold are adapted. Further, a digital encoder algorithm is proposed for efficient digital process. The chip has been fabricated with $0.18{\mu}m$ 1-poly 4-metal n-well CMOS technology. The effective chip area is $2000{\mu}m{\times}1100{\mu}m$ and it consumes about 250mW at 1.8V power supply. The measured SNDR is about 46dB at 10MHz sampling frequency.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.6
• /
• pp.1049-1056
• /
• 2016

In this paper, a design method for a compact dual-band slot antenna with bent slot is studied. Bent slots are added on the rectangular slot of the proposed antenna for dual-band operation. The rectangular slot is fed by a coaxial cable by placing a rectangular feeding patch inside the slot. When the bent slots are added onto the both corner of the upper side of the rectangular slot symmetrically, a new resonant frequency is created in low frequency because of the increasement of the slot length. A prototype of the proposed dual-band slot antenna operating at 2.45 GHz WLAN band and 4.50-8.30 GHz band including 5GHz WLAN band is fabricated on an FR4 substrate with a dimension of 30 mm by 30 mm. Experiment results show that the antenna has a desired impedance characteristic with a frequency band of 2.40-2.49 GHz and 4.33-9.85 GHz for an input reflection coefficient < -10 dB.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.2
• /
• pp.1-6
• /
• 2002

In this paper, an Analog Flat Panel interface(AFPI) which supports for UXGa(Ultar extended Graphics Array)-Compatible TFT LCD Driver is designed. The Proposed AFPI is composed of 8-b ADC, Automatic Gain Control(AGC), Low-Jitter PLL. In order to obtain a high speed and low power consumption, an efficient architecture of 8-bit ADC is proposed, whose FR(Folding Rate) is 8, NFB(Number of Folding Block) is 2, and IR (Interpolating Rate) is 16. We can get high SNDR by adopting distributed track and hold circuits. Also a programmable AGC which is possible to control gain and clamp, and a low-jitter PLL are proposed. The chip has been fabricated with 0.25${\mu}{\textrm}{m}$ 1-poly S-metal n-well CMOS technology. The effective chip area is 3.6mm $\times$ 3.2mm and it dissipates about 602㎽ at 2.5V power supply. The INL and DNL are within $\pm$ 1LSB. The measured SNDR is about 43㏈, when the input frequency is 10MHz at 200MHz clock frequency.

• Journal of Sensor Science and Technology
• /
• v.4 no.4
• /
• pp.23-28
• /
• 1995

The ISFET glucose and sucrose sensors containing platinum electrode and photopolymeric enzyme membrane were fabricated. The platinum working electrode was used for the electrolysis of hydrogen peroxide, which was the other product of the enzyme reaction, to improve sensing characteristics of the sensors. In order to improve response time, photo-crosslinkable polymer(PVA-SbQ) was used to the matrix for the enzyme immobilized membrane. The characteristics of glucose and sucrose sensors were investigated according to the variation of platinum electrode area. The response time was about $3{\sim}5$ minutes and determinations of glucose and sucrose in the range of about $30{\sim}300mg/dl$ could be possible.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.4
• /
• pp.61-68
• /
• 2013

As an advance study for the development of a heat sink for special purpose high power illumination, an investigation was made to find feasibility for the application of copper plated EP to a heat sink of small LED light of less than 10W installed in commercial product. In this study, the plated heat sink with EP copper was fabricated for the conventional LED light. It was used actually for finding heat radiation property and effectiveness of the heat sink accompanied with measurement of luminous intensity. The heat is radiated by transfer and dissipation only through the copper plated surface due to extremely low heat conductivity of EP in case of EP heat sink; however the total area of the plate plays the function of heat transfer as well as heat radiation in case of the aluminum heat sink. It seems that the volume difference of heat radiating material is so big that the temperature $P_1$ is 9.0~12.3% higher in 3W and 42.7~54.0% higher in case of 6W volume difference of heat radiating material is so big that the temperature $P_1$ is 9.0~12.3% higher in 3W and 42.7~54.0% higher in case of 6W even though heat transfer rate of copper is approximately 1.9 times higher than that of aluminum. It was thought that this is useful to utilize for heat sink for low power LED light with the low heating rate. Also, the illumination could be greatly influenced by the surrounding temperature of the place where it is installed. Therefore, it seems that the illumination installation environment must be taken into consideration when selecting illumination. Further study was expected on order to aims at development of an exterior surface itself made into heat radiation plate by application of this technology in future.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.12
• /
• pp.1893-1899
• /
• 2010

A foxtail moves forward on a flat surface when pushed by a vertical force. The distance moved by the foxtail depends on the degree of deformation. We experimentally investigated the main parameters that influence the distance moved while varying the pushing force, area, and velocity. We then fabricated a nylon barb that mimics the foxtail barb and performed theoretical and experimental analyses of the displacement according to the acting force and the deflection. In addition, we investigated the relation between the displacement and the angle of a foxtail-like robot's leg by varying the clearance between the robot body and the inner surface of the pipe. To find the design parameters of the barb of the robot for tubular-type digestive organs and blood vessels, we studied the relation between the acting force and the elastic modulus while varying the leg diameter.