• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.12
• /
• pp.597-600
• /
• 2002

Film Bulk Acoustic wave Resonator (FBAR) using thin piezoelectric films can be made as monolithic integrated devices with compatibility to semiconductor process, leading to small size and low cost, high Q RF circuit elements with wide applications in communications area. This paper presents a MMIC compatible suspended FBAR using surface micromachining. Membrane is composed $Si_3N_4SiO_2Si _3N_4$ multi layer and air gap is about 50${\mu}{\textrm}{m}$. Firstly, We perform one dimensional simulation applying transmission line theorem to verify resonance characteristic of the FBAR. Process of the FBAR is used MEMS technology. Fabricated FBAR resonate at 2.4GHz, $K^2_{eff}$ and Q are 4.1% and 1100.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.12
• /
• pp.1039-1044
• /
• 2002

Film Bulk Acoustic Resonator (FBAR) using thin piezoelectric films can be made as monolithic integrated devices with compatibility to semiconductor process, leading to small size, low cost and high Q RF circuit elements with wide applications in communications area. This paper presents an MMIC compatible suspended FBAR using SOI micromachining. It is possible to make a single crystal silicon membrane using a SOI wafer In fabricating active devices, SOI wafer offers advantage which removes the substrate loss. FBAR was made on the 12㎛ silicon membrane. Electrode and Piezoelectric materials were deposited by RF magnetron sputter. The maximum resonance frequency of FBAR was shown at 2.5GHz range. The reflection loss, K$^2$$\_$eff/, Q$\_$serise/ and Q$\_$parallel/ in that frequency were 1.5dB, 2.29%, 220 and 160, respectively.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.376-380
• /
• 2005

The paper presents some methods to improve characteristics of film bulk acoustic resonator (FBAR) devices. The FBAR devices were fabricated on Bragg reflectors. Thermal treatments were done by sintering and/or annealing processes. The measurement showed a considerable improvement of return loss (S$_{11}$) and quality factor (Q$_{s/p}$). These thermal techniques seem very promising for enhancing FBAR resonance performance.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.2
• /
• pp.311-315
• /
• 2005

In this paper, we emphasize the advantage of thermal annealing treatments for improvement characteristics of film bulk acoustic resonator (FBAR) devices. The FBAR devices were fabricated on multi-layer thin films, namely, Bragg reflectors. Sintering and/or annealing processes were applied in our experiments. The measurements confirm once again a considerable improvement of return loss $(S_{11})$ and quality factor $(Q_{s/p})$. these thermal treatment techniques are really promising for enhancing performance of FBAR resonators in industry fabrication of RF devices.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.8
• /
• pp.716-722
• /
• 2003

ZnO thin films were deposited on Al and Pt electrodes by an RF reactive sputtering system for the fabrication of FBAR (film bulk acoustic wave resonator), and the effect of thermal treatment temperature on their c-axis preferred orientation was investigated. SEM experiments show that columnar structure of ZnO thin films were grown with c-axis normal to electrode material, and XRD experiments show that both ZnO films were grown with (002) plane preferred orientation, but larger diffraction peak was observed with Pt electrode. The peak intensity increased with higher thermal treatment temperature, but c-axis preferred orientation was diminished. The surface roughness of Al thin film was higher than that of Pt, and these affect the surface roughness of ZnO film deposited on the electrode. Though the preferred orientation with respect to Pt(111) plane was improved with higher thermal treatment temperature, this could not improve the c-axis orientation of ZnO film.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.7
• /
• pp.308-314
• /
• 2005

The 2 GHz film bulk acoustic wave resonator(FBAR), one of the most necessary device of the next generation mobile communication system, consisted of solidly mounted resonator(SMR) structure using Brags reflector, was researched in this paper The FBAR applied SiO$_{2}$ and W had large difference of the acoustic impedance to reflector Al to electrode and ZnO to piezoelectric layer. Specially, the FBAR applied the two-step deposition method to improve the c-axis orientation and increase reproducibility of the fabrication device had good performance. The electrical properties of plasma such as impedance, resistance, reactance, $V_{pp},\;I{pp}$, VSWR and phase difference of voltage and current, was analyzed and measured by RF sensor with the variable experiment process factors such as gas ratio, RF power and base vacuum level about concerning the thickness, c-axis orientation, adhesion and roughness. The FBAR device about the optimum condition resulted reflection loss(S$_{11}$) of -17 dB, resonance frequency of 1.93 GHz, electric-mechanical coefficient(k$_{eff}$) of 2.38 $\%$ and Qualify factor of 580. It was seen better qualify than the common dielectric filter at present and expected on business to the filter device of 2 GHz bandwidth with the MMIC technology.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.10a
• /
• pp.61-65
• /
• 2008

In this paper, we studied a ZnO-based film bulk acoustic resonator (FBAR) device fabricated on a specially designed multi-layerd Bragg reflector part. Very thin chromium adhesion layers (0,03um thick) were additionally deposited to improve the quality of the Bragg reflector and some thermal treatments were performed to improve the resonant characteristics of the device. At the operating frequency of ${\sim}2.7GHz$, excellent resonant characteristics were observed in terms of return loss and quality factor, and effective electromechanical coupling coefficient. These findings are expected to be highly promising and effective for improving the performance of the FBAR devices at high frequency.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.5
• /
• pp.1029-1034
• /
• 2012

This paper presents a cost-effective and high-performance film bulk acoustic resonator (FBAR) duplexer module for US-PCS handset applications. The FBAR device uses a glass wafer level packaging process, which is a more cost-effective alternative to the typical silicon capping process. The maximum insertion losses of the FBAR duplexer at the Tx and Rx bands are of 1.9 and 2.4 dB, respectively. The total thickness of the duplexer module is 1.2 mm, including the glass-wafer bonded Tx/Rx FBAR devices, PCB board, and transfer molding material.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.2
• /
• pp.164-168
• /
• 2005

Piezoelectric ZnO thin films were for the first time formed on SiO$_2$/Si(100) substrate using 2-step deposition, atomic layer deposition(ALD) and RF magnetron sputtering deposition, for film bulk acoustic resonator(FBAR) applications. The ZnO buffer layer by ALD was deposited using alternating diethyl zinc(DEZn)/$H_2O$ exposures and ultrahigh purity argon gas for purging. The ZnO films by 2-step deposition revealed stronger c-axis-preferred orientation and smoother surface than those by the conventional RF sputtering method. The solidly mounted resonator(SMR)-typed FBAR fabricated by using 2-step deposition method revealed higher quality factor of 580 and lower return loss of -17.35dB. Therefore the 2-step deposition method in this study could be applied to the FBAR device fabrication.

• Journal of information and communication convergence engineering
• /
• v.3 no.4
• /
• pp.167-171
• /
• 2005

In this paper, the resonance characteristics of SMR-type FBAR devices annealed by three different annealing methods are investigated and compared. The resonance characteristics could be effectively improved by the proposed efficient annealing method which optimizes the annealing conditions. It seems very useful for improving the performance of the SMR-type FBAR devices as a cost-effective way.