• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.12
• /
• pp.948-953
• /
• 2017

When using a high-power amplifier(HPA) for high-speed communication, the nonlinear characteristics of the HPA deteriorate power efficiency, bit error rate(BER) performance, and spectral efficiency. Because it is inevitable to use the HPA to obtain sufficient transmission power for high-speed communication, it is necessary to compensate for nonlinearity of the HPA by using a predistorter. In this study, a predistorter was used to compensate for the nonlinearity of the HPA, and the nonlinear distortion was compensated using the predistorter. Simulation results show that the compensation of the nonlinearity of the HPA using the predistorter achieves a BER performance similar to that of an ideal linear amplifier, and that the spectral mask is also satisfied.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.7
• /
• pp.23-29
• /
• 2011

A dB-linearity improved variable gain amplifier (VGA) for GPS receiver is presented. The Proposed dB-linear current generator has improved dB-linearity error of ${\pm}0.15$dB. The VGA for GPS is designed using proposed dB-linear current generator and composed of 3 stage amplifiers. The IF frequency is assumed as 4MHz and the linearity requirement of the VGA for GPS receiver is defined as 24dBm of IIP3 using cascaded IIP3 equation and the VGA satisfies 24dBm when minimum gain mode. The DC-offset voltage is eliminated using DC-offset cancelation loop. The gain range is from -8dB to 52dB and the dB-linearity error satisfies ${\pm}0.2$dB. The 3-dB frequency has range of 35MHz~106MHz for the gain range. The VGA is designed using 0.18${\mu}m$ CMOS process. The power consumption is 3mW with 1.8V supply voltage.

• Journal of IKEEE
• /
• v.18 no.4
• /
• pp.586-592
• /
• 2014

In this paper, high efficiency power management IC(PMIC) with DT-CMOS(Dynamic threshold voltage Complementary MOSFET) switching device is presented. PMIC is controlled PWM control method in order to have high power efficiency at high current level. The DT-CMOS switch with low on-resistance is designed to decrease conduction loss. The control parts in Buck converter, that is, PWM control circuit consist of a saw-tooth generator, a band-gap reference(BGR) circuit, an error amplifier, comparator circuit, compensation circuit, and control block. The saw-tooth generator is made to have 1.2MHz oscillation frequency and full range of output swing from supply voltage(3.3V) to ground. The comparator is designed with two stage OP amplifier. And the error amplifier has 70dB DC gain and $64^{\circ}$ phase margin. DC-DC converter, based on current mode PWM control circuits and low on-resistance switching device, achieved the high efficiency nearly 96% at 100mA output current. And Buck converter is designed along LDO in standby mode which fewer than 1mA for high efficiency. Also, this paper proposes two protection circuit in order to ensure the reliability.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.1
• /
• pp.59-67
• /
• 2016

A novel instrumentation amplifier (IA) using fully-differential linear operational transconductance amplifier (FLOTA) for electronic measurement systems with low cost, wideband, and gain control with wide range is designed. The IA consists of a FLOTA, two resistor, and an operational amplifier(op-amp). The principal of the operating is that the difference of two input voltages applied into FLOTA converts into two same difference currents, and then these current drive resistor of (+) terminal and feedback resistor of op-amp to obtain output voltage. To verify operating principal of the IA, we designed the FLOTA and realized the IA used commercial op-amp LF356. Simulation results show that the FLOTA has linearity error of 0.1% and offset current of 2.1uA at input dynamic range ${\pm}3.0V$. The IA had wide gain range from -20dB to 60dB by variation of only one resistor and -3dB frequency for the 60dB was 10MHz. The proposed IA also has merits without matching of external resistor and controllable offset voltage using the other resistor. The power dissipation of the IA is 105mW at supply voltage of ${\pm}5V$.

• Journal of IKEEE
• /
• v.12 no.3
• /
• pp.167-171
• /
• 2008

A bridge resistance deviation-to-frequency (BRD-to-F) converter is presented for interfacing resistive sensor bridges. It consists of a linear operational transconductance amplifier (LOTA), a current-controlled oscillator (CCO). The prototype converter was simulated using commercially available discrete components. The result shows that the converter has a conversion sensitivity amounting to 16.90 kHz/${\Omega}$ and a linearity error less than ${\pm}$0.03 %.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.11
• /
• pp.2451-2456
• /
• 2011

This paper is a study on the high power amplifier to fulfill standards of the MOPS. VDR's frequency band is 117.975~137MHz, and CSMA(Carrier Sense Multiple Access), D8PSK(Differential Eight Phase Shift Keyed), 25KHz's channel bandwidth use. It also stated in DO-281A MOPS output power, symbol constellation error, spurious emissions, adjacent channel power must be met. We designed and measured the performance. The 38dB of the IM3 satisfies the MOPS standard.

• ETRI Journal
• /
• v.36 no.3
• /
• pp.510-513
• /
• 2014

A Q-band pHEMT image-rejection low-noise amplifier (IR-LNA) is presented using inter-stage tunable resonators. The inter-stage L-C resonators can maximize an image rejection by functioning as inter-stage matching circuits at an operating frequency ($F_{OP}$) and short circuits at an image frequency ($F_{IM}$). In addition, it also brings more wideband image rejection than conventional notch filters. Moreover, tunable varactors in L-C resonators not only compensate for the mismatch of an image frequency induced by the process variation or model error but can also change the image frequency according to a required RF frequency. The implemented pHEMT IR-LNA shows 54.3 dB maximum image rejection ratio (IRR). By changing the varactor bias, the image frequency shifts from 27 GHz to 37 GHz with over 40 dB IRR, a 19.1 dB to 17.6 dB peak gain, and 3.2 dB to 4.3 dB noise figure. To the best of the authors' knowledge, it shows the highest IRR and $F_{IM}/F_{OP}$ of the reported millimeter/quasi-millimeter wave IR-LNAs.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.10
• /
• pp.9-15
• /
• 2009

In this paper, we invented a new structure of fast ATC(Automatic Threshold Control) circuit. Using the structure we made a new burst-mode limiting amplifier with fast ATC function using commercial $0.8{\mu}m$ BiCMOS technology. It's ATC function worked so fast that even the first bit of burst-data could be detected, which confirmed that the new structure was useful for fast ATC. However, in the beginning of a burst, distortions in duty-cycle occurred and increased up to 59% of duty-cycle as amplitude of input signal increased. But we confirmed that after 10 cycles passed, duty-cycles was staying below 52% of duty-cycle for any magnitude of input signal.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.2
• /
• pp.280-285
• /
• 2015

A fully integrated high-efficiency linear CMOS power amplifier (PA) is developed for 802.11n WLAN applications using the 65-nm standard CMOS technology. The transformer topology is investigated to obtain a high-efficiency and high-linearity performance. By adopting a 2:2 output transformer, an optimum impedance is provided to the PA core. Besides, a LC harmonic control block is added to reduce the AM-to-AM/AM-to-PM distortions. The CMOS PA produces a saturated power of 26.1 dBm with a peak power-added efficiency (PAE) of 38.2%. The PA is tested using an 802.11n signal, and it satisfies the stringent error vector magnitude (EVM) and mask requirements. It achieves -28-dB EVM at an output power of 18.6 dBm with a PAE of 14.7%.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.5
• /
• pp.257-260
• /
• 2017

In this paper, we present the design of a 4.5 V low dropout (LDO) voltage regulator implemented in the 130 nm CMOS process. The design uses a two-stage cascaded operational transconductance amplifier (OTA) as an error amplifier, with a body bias technique for reducing dropout voltages. PMOS is used as a pass transistor to ensure stable output voltages. The results show that the proposed LDO regulator has a dropout voltage of 32.06 mV when implemented in the130 nm CMOS process. The power dissipation is only 1.3593 mW and the proposed circuit operates under an input voltage of 5V with an active area of $703{\mu}m^2$, ensuring that the proposed circuit is suitable for low-power applications.