• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.11A
• /
• pp.1146-1153
• /
• 2007

In this paper, we analyze the I/Q imbalances effects at the WiBro uplimk when using direct-conversion RF transceiver. If I/Q imbalance exists, the transmit signal is spread over two sbcarriers. As a result, phenomenon of performance reducing is produced. Contrary to OFDM system in which one user uses all subcarrier, symmetrical two subcarriers are assigned other users in OFDMA system. I/Q imbalances elements can't be estimated such a conventional allocation method of tiles in subchannel and compensated. In order to solve the problem, We propose a new method in order that symmetrical two subcarriers are assigned one user. If novel method is applied, we can estimate I/Q imbalances and compensate distortion received signal. As a result, we can obtain a performance similar performance when I/Q imbalances is not existed. Also, if proper detection methods are used, we get the effect of performance improvement, because of diversity gain what is happened due to combining I/Q imbalances with multi path fading channel.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.3
• /
• pp.324-330
• /
• 2013

This paper describes a novel method to surface large optics mirror with an extremely high hardness, which could replace the high cost of the repetitive off-line measurement steps and the large ultra-precision grinding machine with ultra-positioning control of 10 nm resolution. A lot of diamond pellet to be attached on the convex aluminum base consists of a grinding tool for the concave large mirror, and the tool was pressured down on the large mirror blank. The tool motion at an interval on the spiral path was controlled with each feed rate as the dwell time in the conventional computer-controlled polishing. The shape to be surfaced was measured directly by a touch probe on the machine without any separation of the mirror blank. Total 40 iterative steps of the surfacing and measurement could demonstrate the form error of RMS $7.8{\mu}m$, surface roughness of Ra $0.2{\mu}m$ for the mirror blank with diameter of 1 m and spherical radius of curvature of 5400 mm.

• Plant Journal
• /
• v.4 no.3
• /
• pp.54-59
• /
• 2008

The resonance of boiler is caused by exciting force in the gas path and it generates the vibration by the harmony of boiler's dimensional factor. According to trending toward the boiler of increasing capacity and a bigger size, it has a problem of the vibration at back-pass heating surfaces. We can predict such vibrations as comparison between vortex frequency and gas column's natural frequency. We can't rely on the method for the past decades because of changing parameters, such as an allowable error, gas temperature, gas velocity, Strouhal number. We can reduce the vibration to use the seasoning effect and change the operating condition in coal fired boiler but it's not essential solution. When the vibration occurred in the model boiler, we must measures the acoustic pressure and frequency of places for considering the means. So far, we confirmed the problem from field measures and theoretical analysis about the acoustic vibration of boiler. We installed anti-acoustic baffle in a existing boiler to change the acoustic natural frequency at the cavity, which results in reducing the acoustic vibration. The first, we prove that the acoustic resonance is caused by harmonizing vortex shedding frequency of tube heat surface with acoustic natural frequency of cavity in the range of 650~750 MW loads. The second, the acoustic resonance at the back-pass heating surface has the third order of acoustic natural frequency at the second economizer. We install five anti-acoustic baffles at the second economizer to reducing the resonance. We confirm considerably reducing the acoustic vibration of boiler during the commercial boiler.

• Archives of design research
• /
• v.17 no.4
• /
• pp.61-68
• /
• 2004

A great variety of handheld device are coming onto the market. Some have advanced features compacted into very small sized hardware. In order to maximize the capability of these devices, we need to understand the characteristics of different input methods and utilize them in a sufficient way. Our study aims to understand characteristics of each device, so that we can design user interfaces more effectively. Two experiments were conducted to compare target pointing performance with a pen and with a hardware key on small displays. In experiment 1, we examined participants' performance of target pointing with both input methods at different target sizes. It was found that pen operation is more erroneous than key based operation when target size is smaller than 5mm, but at a target size of 5mm, the error rate decreased to the same level as for key input. In experiment 2, we examined the effect of the number of targets. The results showed, with a target size of 5mm, the pen could point to targets quicker than with key input, when the distance to the target exeeds a path length of 3 steps.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.10
• /
• pp.2367-2372
• /
• 2015

One of various low-density parity-check(LDPC) codes that has been adopted in many communication standards due to its error correction ability is a quasi-cyclic LDPC(QC-LDPC) code, which leads to comparable decoder complexity. One of the main blocks in the QC-LCDC code decoder is a multi-size circular shifter(MSCS) that can perform various size rotation. The MSCS can be implemented with many structures, one of which is based on Banes network. The Benes network structure can perform the normal MSCS operation efficiently, but it cannot use the properties coming from specifications like rotation sizes. This paper proposesd a scheme where the Benes network structure can use the rotation size property with the modification of the control signal generation. The proposed scheme is applied to the MSCS of IEEE 802.16e WiMAX QC-LDPC decoder to reduce the number of MUXes and the critical path delay.

• Journal of Navigation and Port Research
• /
• v.35 no.8
• /
• pp.643-647
• /
• 2011

In this paper, we study the application of DSSS(Direct Sequence Spread Spectrum) in underwater acoustic communication for robust the ISI(Inter-Symbol Interference. We confirm the application of DSSS in underwater acoustic communication in underwater by the simulation with underwater channel impulse response and experiment. As a simulation result, the BER of QPSK technique is $1.14{\times}10^{-1}$ and the BER of DSSS technique is $6.73{\times}10^{-3}$. And we performed the experiment of DSSS technique in underwater. As a experiment result, the BER of QPSK technique is $3.19{\times}10^{-1}$ and the BER of DSSS technique is $5.17{\times}10^{-4}$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.10
• /
• pp.1879-1885
• /
• 2017

This paper discusses the trajectory tracking system of unmanned ground vehicles based on predictive control. Because the unmanned ground vehicles can not satisfactorily complete the path tracking task, highly efficient and stable trajectory control system is necessary for unmanned ground vehicle to be realized intelligent and practical. According to the characteristics of unmanned vehicle, this paper built the kinematics tracking models firstly. Then studied algorithm solution with the tools of the optimal stability analysis method and proposed a tracking control method based on the model predictive control. The controller used a kinematics-based prediction model to calculate the predictive error. This controller helps the unmanned vehicle drive along the target trajectory quickly and accurately. The designed control strategy has the true robustness, simplicity as well as generality for kinematics model of the unmanned vehicle. Furthermore, the computer Simulink/Carsim results verified the validity of the proposed control method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.5B
• /
• pp.413-420
• /
• 2006

HMIPv6 is designed to reduce the signaling load to external network and improve handover speed of MN by including Mobility Anchor Point(MAP) in local handover. However in this case of macro handover, it's just used pervious MIPv6 handover algorithm. So, it occurs packet loss and transmission delay problem. In this paper, we propose the mechanism applying the HMIPv6 for Fast Handover to choose suitable to the condition buffering handover. The condition for the selection is result distance measurement between MN and CN, between MN and NAR. Furthermore, using F-SNOOP protocol, it is possible to improve wireless network performance. Wireless network has high Bit Error Rate(BER) characteristic because of path loss, fading, noise and interference. TCP regards such errors as congestion and starts congestion control. This congestion control makes packet transmission rate low. However, F-SNOOP improves TCP performance based on SNOOP and Freeze TCP that use Zero Window Advertisement(ZWA) message when handoff occurs in wireless network.

• The Transactions of the Korea Information Processing Society
• /
• v.6 no.8
• /
• pp.2204-2212
• /
• 1999

In this paper, we present techniques which perform incremental timing analysis using Timed Boolean Algebra that solves the false path problem and extracts the timing information in combinational circuits. Our algorithm sets histories of internal inputs that are substituted for internal output and extracts maximal delays through checking sensitizability of primary outputs. Once finding the sum of primitive delay terms, then it applies modified delay with referencing histories of primary output and it can extract maximal delays of primary outputs fast and efficiently. When the structure of circuit is changed, there is no need to compute the whole circuit again. We can process partial timing analysis of computing on the gates that are need to compute again. These incremental timing analysis methods are considered both delay changes and structure of circuit, and can reduce the costs of a trial error in the circuit design.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.10C
• /
• pp.921-926
• /
• 2006

The Presence of a line-of-sight(LoS) blockage can degrade the UWB positioning accuracy for two reasons. Firstly, it makes estimation of the time of arrival(ToA) of the direct path signal difficult by complicating the multipath structure of the propagation channel. Secondly, the higher dielectric constant of the LoS blocking material than that of free space introduces excess propagation delay which will bias the range estimation. In this paper, methods based on ray tracing to reduce the ranging error resulting from the second reason are Posed. We take two different approaches; a statistical approach and a map-aided method. In the statistical approach, we establish a conditional distribution of the excess propagation delay caused by LoS blockages using a ray tracing technique. The lo6wer bound of the ranging performance based on this model is estimated. Ine ray tracing method is also used for the map-aided ToA positioning approach. UWB propagation measurement data taken in an office environment is used to examine the performance of this method.