• 한국재료학회지
• /
• 제15권5호
• /
• pp.313-317
• /
• 2005

The relation between bulk microdefect (BMD) and mechanical strength of $P/P^-$ epitaxial silicon wafers (Epitaxial wafer) as a function of nitrogen concentrations was studied. After 2 step anneal$(800^{\circ}C/4hrs+1000^{\circ}C/16hrs)$, BMD was not observed in nitrogen undoped epitaxial silicon wafer while BMD existed and increased up to $3.83\times10^5\;ea/cm^2$ by addition of $1.04\times10^{14}\;atoms/cm^3$ nitrogen doping. The slip occurred for nitrogen undoped and low level nitrogen doped epitaxial wafers. However, there was no slip occurrence above $7.37\times10^{13}\;atoms/cm^3$ nitrogen doped epitaxial wafer. Mechanical strength was improved from 40 to 57 MPa as nitrogen concentrations were increased. Therefore, the nitrogen doping in silicon wafer plays an important role to improve BMD density, slip occurrence and mechanical strength of the epitaxial silicon wafers.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 추계학술대회 논문집 학회본부
• /
• pp.317-319
• /
• 1997

We have studied the properties of $GaAs_{1-x}P_x$ epitaxial films on the GaP using VPE method by CVD. The surface carrier concentration and PL power increased with increasing the epitaxial temperature while PL wave length decreased. The Power out of the LED with $GaAs_{1-x}P_x$/GaP structure decreased with increasing the epitaxial temperature while the forward voltage of the LED increased. Specially, The LED of $GaAs_{1-x}P_x$/GaP structure represents good electrical and optical properties when the $GaAs_{1-x}P_x$ layer was epitaxially grown at $810^{\circ}C$.

• Journal of Magnetics
• /
• 제6권4호
• /
• pp.129-131
• /
• 2001

In order to investigate the effect of the interface on GMR, [NiFe(25 ${\AA}$)/Cu(24${\AA}$)]$_2$/Si thin film was epitaxially grown on HF-treated Si (001) substrate using a DC magnetron sputtering method. Typical GMR effects could be observed in epitaxial film with a weak antiferromagnetic exchange coupling while non epitaxial film showed unsaturated and broad MR curves probably due to inter-diffusion between NiFe and Cu layers. Ferromagnetic resonance (FMR) experiment showed two distinct absorption peaks in all films. Each peak was revealed to come from each NiFe layer with different magnetic property. In FMR measurement very clear interface in epitaxial films could be confirmed by a lower value of line width (ΔH) and higher M$\sub$s/ of epitaxial film than those of non epitaxial films, respectively.

• 한국재료학회지
• /
• 제20권12호
• /
• pp.645-648
• /
• 2010

The structure and morphology of epitaxial layer defects in epitaxial Si wafers produced by the Czochralski method were studied using focused ion beam (FIB) milling, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Epitaxial growth was carried out in a horizontal reactor at atmospheric pressure. The p-type Si wafers were loaded into the reactor at about $800^{\circ}C$ and heated to about $1150^{\circ}C$ in $H_2$. An epitaxial layer with a thickness of $4{\mu}m$ was grown at a temperature of 1080-$1100^{\circ}C$. Octahedral void defects, the inner walls of which were covered with a 2-4 nm-thick oxide, were surrounded mainly by $\{111\}$ planes. The formation of octahedral void defects was closely related to the agglomeration of vacancies during the growth process. Cross-sectional TEM observation suggests that the carbon impurities might possibly be related to the formation of oxide defects, considering that some kinds of carbon impurities remain on the Si surface during oxidation. In addition, carbon and oxygen impurities might play a crucial role in the formation of void defects during growth of the epitaxial layer.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제17권2호
• /
• pp.271-276
• /
• 2017

The triple-gate tunnel FETs encapsulated with an epitaxial layer (EL TFETs) is proposed to lower the subthreshold swing of the TFETs. Furthermore, the band-to-band tunneling based on the maximum electric-field can occur thanks to the epitaxial layer wrapping the Si fin. The performance and mechanism of the EL TFETs are compared with the previously proposed TFET based on simulation.

• 대한전자공학회논문지
• /
• 제26권8호
• /
• pp.1290-1298
• /
• 1989

A new dynamic RAM cell called Trench Epitaxial Transistor Cell (TETC) has been developed for 4M to 16M DRAMS. Also the fabrication process for device isolation which can decrease the narrow effect using SEG process has been developed. We verified the characteristic of the new cell structure with the PICSES simulator on VAX8450.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 D
• /
• pp.1249-1251
• /
• 1998

We have studied the properties of $GaAs_{0.35}P_{0.65}$ epitaxial films on the GaP according to doping of $NH_3$ gas using VPE method by CVD. The efficiency of $GaAs_{0.35}P_{0.65}$ epitaxial films found to be greatly enhanced by the according of nitrogen doping. The diodes were fabricated by means of Zn diffusion into vapor grown $GaAs_{0.35}P_{0.65}$ epitaxial films doped with N and Te. The effects of nitrogen doping on carrier density of epitaxial films, PL wavelength and the power out, forward voltage of diodes are discussed. In the end, The effect of electrical and optical properties is influenced by the deep level and deep level density of nitrogen doping.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2007년도 하계학술발표회 논문집
• /
• pp.237-238
• /
• 2007

A new strain analysis model, so called the stress matched model, in an epitaxial multilayer system is proposed. The model makes it possible to know the strain, the stress, the elastic strain energy in each epitaxial layer. Analytical formulas of strain parameters in each epitaxial layer are derived under assumptions that the substrate thickness is finite and the in-plane lattice constant is the same for all epitaxial layers for dislocation free growth. As an example, the model is applied to a 405nm InGaN/InGaN multiple quantum well laser diode. Analysis result shows that AlxGa1-xN layer with Al mole fraction of 0.06 and the thickness of 6${\mu}m$ is one of good templates for a laser. In fact, this layer structure coincides with experimentally optimized one.

• 한국산업융합학회 논문집
• /
• 제4권4호
• /
• pp.451-455
• /
• 2001

The epitaxial growth of Ge on the clean and surfactant(Sn) adsorbed surface of Ge(111) was studied by the intensity oscillation of a RHEED specular spot. In the case of epitaxial growth without the adsorbed surfactant, the RHEED intensity oscillation was stable and periodic up to 24ML at the substrate temperature of $200^{\circ}C$. Therefore the optimum temperature for the epitaxial growth of Ge on clean Ge(111) seems to be $200^{\circ}C$. However, in the case of epitaxial growth with the adsorbed surfactant, the irregular oscillations are observed in the early stage of the growth. The RHEED intensity oscillation was very stable and periodic up to 38ML, and the $d2{\times}2$ structure was not charged with continued adsorption of Ge at the substrate temperature of $200^{\circ}C$. These results may be explained by the fact that the diffusion length of Ge atoms is increased by decreasing the activation energy of the Ge surface diffusion, resulted by segregation of Sn toward the growing surface. From the desorption process, the desorption energy of Sn in Ge $\sqrt{5}{\times}\sqrt{5}$ structure is observed to be 3.28eV.

• 한국재료학회지
• /
• 제13권2호
• /
• pp.88-93
• /
• 2003

Co/Ti bilayer structure in Co salicide process helps to the improvement of device speed by lowering contact resistance due to the epitaxial growth of $CoSi_2$layers. We investigated the epitaxial growth and interfacial mass transport of $CoSi_2$layers formed from $150 \AA$-Co/Ti structure with two step rapid thermal annealing (RTA). The thicknesses of Ti layers were varied from 20 $\AA$ to 100 $\AA$. After we confirmed the appropriate deposition of Ti film even below $100\AA$-thick, we investigated the cross sectional microstructure, surface roughness, eptiaxial growth, and mass transportation of$ CoSi_2$films formed from various Ti thickness with a cross sectional transmission electron microscopy XTEM), scanning probe microscopy (SPM), X-ray diffractometery (XRD), and Auger electron depth profiling, respectively. We found that all Ti interlayer led to$ CoSi_2$epitaxial growth, while $20 \AA$-thick Ti caused imperfect epitaxy. Ti interlayer also caused Co-Ti-Si compounds on top of $CoSi_2$, which were very hard to remove selectively. Our result implied that we need to employ appropriate Ti thickness to enhance the epitaxial growth as well as to lessen Co-Ti-Si compound formation.