• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.3
• /
• pp.210-217
• /
• 2009

This paper presents the analytical prediction of stability lobes in milling. The stability lobes are obtained by measuring the frequency response function (FRF) of a machining center at the cutting point of the end mill cutter, identifying cutting constants, and approximating cutting force coefficients. The stability lobes are experimentally verified through cutting tests.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.241-246
• /
• 2013

The regulation of the aircraft noise has been more strengthened with expansion of the environmental issue. This trend has encouraged the R&D of the noise reduction technology. In this paper, the international efforts for aircraft noise reduction and the related technology were investigated. The aircraft noise sources were also introduced briefly. Additionally, the noise prediction method was explained at the end of paper.

• Journal of Mechanical Science and Technology
• /
• v.17 no.8
• /
• pp.1156-1163
• /
• 2003

The pseudospectral method is applied to the analysis of in-plane free vibration of circularly curved Timoshenko beams. The analysis is based on the Chebyshev polynomials and the basis functions are chosen to satisfy the boundary conditions. Natural frequencies are calculated for curved beams of rectangular and circular cross sections under hinged-hinged, clamped-clamped and hinged-clamped end conditions and the results are compared with those by transfer matrix method. The present method gives good accuracy with only a limited number of collocation points.

• Journal of KSNVE
• /
• v.4 no.4
• /
• pp.451-457
• /
• 1994

A numerical method is presented to obtain natural frequencies and mode shapes of uniform elastic beams with static deflections due to dead loads. The differential equation governing the free vibration of beam taken into account the static deflection due to deal loads is derived and solved numerically. The hinged-hinged, clamped-clamped and clamped-hinged end constraints are applied in the numerical examples. As the numerical results, the lowest three nondimensional frequency parameters are reported as functions of nondimensional system parameters; the load parameters, and the slenderness rations. And some typical mode shapes of free vibrations are also presented in figures.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.888-891
• /
• 2001

Effects of backing conditions on the impedance tube measurement are investigated experimentally, by using several pairs of generally employed end conditions. The results show that the measured values are similar for most of pairs, except the case of using an open pipe condition. In addition, the random error is investigated in the viewpoint of the variation of test conditions. The multi-termination method is suggested for minimizing such a random error.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2276-2279
• /
• 2011

The AUTS(Advanced Urban Transit System) are developed by government R&D business. This units are under main line performance test in Daebul test line. Both AC and DC could apply to the AUTS for pantagraph voltage. So main transformer and some high voltage filters are added to the under-frame. As a result the total weight of each car(Mc1-Tp1-M-T-Tp2-Mc2) is different. And axle load is different each other. The main characteristics of AUTS(Advanced Urban Transit System) are as follows. One inverter control one motor, DDM(Dircet Drive Motor), no driving gear, plug no end door, self-steering bogie etc. These matters could be appeared to strange vibration. So vibration test is important. The vibration test performed to Mc1 and Tp1. The results were checked to the up-down direction and left-right direction for acceleration.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.6
• /
• pp.1016-1025
• /
• 2002

This paper deals with the measurement of the fluid viscosity by using the torsional vibration of a circular rod excited by a torsional vibrator at one end. The effect of an adjacent viscous fluid on the torsional vibration of the rod has been studied theoretically and expressed in terms of the mechanical impedance. The theoretically-obtained trend that the mechanical impedance is proportional to the square root of the viscosity times the density of the fluid has been confirmed by the impedance measurement. The paper demonstrates that a torsionally-vibrating rod can be used as a sensor to measure the viscosity of a fluid.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.11
• /
• pp.852-859
• /
• 2003

In order to meet the growing demands for higher storage density as well as lower noise level, the spindles in hard disk drives are to be supported by hydrodynamic bearings in place of conventional ball-type ones. However, the existing models are inappropriate to apply to accurate prediction of vibration characteristics because the HDD spindle tends to take quite a complex shape to secure its performance and cost-effectiveness. In this context, this paper treats analysis of free and forced vibrations of such-designed HDD spindles based on more sophisticated models and validations via experiments. Remarkably, to this end all the components in the system are modeled as elastic adopting the finite element method.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.3
• /
• pp.201-207
• /
• 2004

High speed rotating airflow inside a HDD chamber causes sub-micron scale disk vibration that could generate significant TMR problems in most of current HDD products. Many publications are presented for the reduction of airflow excitation. One of the most effective methods widely adopted in high-end HDD products is SqueezeAir Bearing Plate (SABP). However, because of its tight assembly clearance between the damper and disk, this method could not be easily implemented in volume production. This article presents a disk damper design that is modified to be feasible for volume production by virtue of a new airflow modeling method.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.3
• /
• pp.230-235
• /
• 2004

This paper deals with the free vibration analysis of circular strip foundations with the variable breadth. Taking into account effects of both rotatory inertia and shear deformation, differential equations governing free vibrations of such foundations are derived. The Winkler foundation is chosen as the model of soil foundation. The breadth of strip foundation is assumed to be a linear function. The differential equations are solved numerically to calculate natural frequencies. In numerical examples, the strip foundations with the hinged-hinged, hinged-clamped. clamped-hinged and clamped-clamped end constraints are considered. The parametric studies are conducted and the lowest four frequency parameters are reported in figures as the non-dimensional forms.