• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.9
• /
• pp.475-480
• /
• 2004

One of the most important issues in AC PDP is the improvement of luminous efficiency. One possible method is to develop new sustain electrode shape showing high luminous efficiency. In this study, a new electrode shapehas a bridge is proposed in order to solve this problem. The experimental results show that the test panel with the suggested new electrode shape shows high luminance efficiency by 35.35% and low sustain voltage by 17V compared with the conventional structure.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.6 s.249
• /
• pp.698-704
• /
• 2006

This paper presents an electrode shape design method for the multi-mode sensors that could deteict the selected structural multiple modes. The structure used for this study is an isotropic cantilever beam type with a PVDF (polyvinylidene fluoride) which is bonded onto the structure as a sensor. The shape optimization problem is solved by using Genetic Algorithm (GA) with an appropriate objective function. The performance of analytical optimal shape sensor is compared with that of experimental work. The results show that the, obtained electrode shape sensors have good performance to detect the multiple vibration modes simultaneously.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.1
• /
• pp.50-57
• /
• 2016

Transmission equipment is mainly used for the XLPE (cross-linked polyethylene) insulation cable for ultra high voltage power to minimize power loss. The experiment examined the partial discharge characteristics according to the insertion of the bar electrode and needle electrode into the XLPE specimen and the air voids. XLPE insulation cable manufactured by T. company and tungsten electrode material by K. company were used for specimens, by adhering conductive tape on the semi-conductive material of the lower electrode of XLPE specimen with the dimension of $16{\times}40{\times}30$ [mm] was used as negative electrode. In order to investigate the PD with ${\phi}$-q-n of XLPE specimen according to the electrode shape and the size of air voids. we examined the PD by varying the voltage after applying voltage of 3~20 kV on the electrode. Therefore, it was confirmed from the result of PD characteristics of specimen that the larger the air void than the gap between electrode (+) and electrode(-), the larger effect on the discharge when the bar electrode and needle electrode inserted into XLPE, and the closer the distance between the insulation and the needle electrode, the faster insulation breakdown.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.2
• /
• pp.80-84
• /
• 2018

In this study, we investigated plasmon effects to maximize the sterilization of dielectric discharge. We predicted the effect using the finite difference time domain (FDTD) method as a function of electrode shape, size, and period. The structure of the electrode was designed with a thickness of 100 nm of silver nanoparticles on a glass substrate, and was varied according to the shape, size, and period of the electrode hole. Based on the results, it was confirmed that the effect of plasmons was independent of the shape of the electrode hole. It was thus confirmed that the plasmon effect depended only on the size and period of the holes. Further, the plasmon effect was affected by the size rather than period of the holes. Because the absorption of light by the metal varied according to the size of the hole, the plasmon effect generated by the absorption of light also varied. The best results were obtained when the radius and period of the electrode holes were $0.1{\mu}m$ and $0.4{\mu}m$, respectively.

• Journal of Welding and Joining
• /
• v.35 no.2
• /
• pp.52-57
• /
• 2017

In this study, resistance spot weldability of lightweight steel with high Al contents was evaluated using various electrode shapes. The six types of electrode shape were prepared with different electrode face diameter and radius. The tensile shear tests were carried out to investigate the failure behaviors. Also, the nugget size and hardness were measured and compared with various electrode shapes. The experimental results show that the acceptable weld current region for low density lightweight steel could be obtained with 10mm electrode face diameter and 76mm electrode face radius.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.721-727
• /
• 2000

Impedance method was carried out to design the electrode that can measure the void fraction of the bubbly flow in pool reservoir. To find out the optimum electrode shape, Styrofoam-tests were performed in a specially designed acrylic reservoir. Three kinds of electrodes were designed to compare the characteristics of water-air flow. The resistance was increased as the void fraction increased and the capacitance was decreased as the void fraction increased. The resistance is a main parameter to express the nature of the water-air flow in impedance method. Almost all the values of impedance were involved in resistance. The degree of deviation from the mean-resistance values showed reasonable results. Electrode type-I expressed excellent results among the three electrode shapes. The impedance values in void fraction 0-10% were similar to those of Maxwell's equation. But the impedance values in void fraction 10-20% were not similar to those of Maxwell' equation because of the edge effect near electrode.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.9
• /
• pp.964-975
• /
• 1990

This paper aims at the design of high voltage electrode contour under specified field condition. Defining the contour with B-Spline curve, the number of contour variables can be reduced and very smooth electrode can be obtained. For the analysis of the electric field, Surface Charge Method which has advantages in practical model has been used. As an initial contour, the rod-plane gap has been used since the difference between maximum and minimum field value is relatively large. Various field conditions including uniform field condition are given to the end of the rod electrode. Under uniform field condition, authors designed an electrode whose field-deviation was under 0.5%. Finally, the relation between the curvature and field of the electrode has been checked, which showed that B-Spline curve is appropriate for the shape function.

• Journal of Welding and Joining
• /
• v.5 no.3
• /
• pp.11-18
• /
• 1987

Effects of electrode tips shapes of spot welding on the galvannealed steel have been studied, and the results obtained from this studies are as follows. 1) Expulsion had no effect on the shear strength of the specimen but been observed on the tensile strength of the specimen. 2) Effect of holding time after welding was neglegible when the spot welding supplies enough heat input. 3) Depending on the sopt welding tip shape it has different weldbility. It has better weldability in the order of pointed shape, truncated shape and dome shape. But the effect of coolind was just the opposite of the above order.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.06a
• /
• pp.261-262
• /
• 2007

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.1
• /
• pp.49-55
• /
• 2009

This paper presents the optimal shape of microelectrode that generates dielectrophoretic(DEP) force to separate particles in homogeneous medium. The principle of the particles sorting is based on the use of the relative strengths of negative DEP (nDEP) and drag forces, as in a general DEP-activated cell sorter (DACS). To numerically calculate the DEP force and drag force, the simulation is implemented in MATLAB 7.0. The properties of particles, which are used in simulation, are similarly selected as those of cells to apply cell separation. The most optimized shape of electrode is selected by numerical simulation according to a variety of electrode shape such as rectangle, trapezoidal, and right-triangle. Through, in addition, parameter study, we found that applied frequency is more significant factor on the separation than various parameters, such as applied voltage and permittivity of medium, that decide on the strength of DEP force.