• Journal of IKEEE
• /
• v.12 no.3
• /
• pp.176-183
• /
• 2008

The high efficiency power management IC(PMIC) with DTMOS(Dynamic Threshold voltage MOSFET) switching device is proposed in this paper. PMIC is controlled with PWM control method in order to have high power efficiency at high current level. DTMOS with low on-resistance is designed to decrease conduction loss. The control parts in Buck converter, that is, PWM control circuits consist of a saw-tooth generator, a band-gap reference circuit, an error amplifier and a comparator circuit as a block. The Saw-tooth generator is made to have 1.2 MHz oscillation frequency and full range of output swing from ground to supply voltage(VDD:3.3V). The comparator is designed with two stage OP amplifier. And the error amplifier has 70dB DC gain and $64^{\circ}$ phase margin. DC-DC converter, based on Voltage-mode PWM control circuits and low on-resistance switching device, achieved the high efficiency near 95% at 100mA output current. And DC-DC converter is designed with LDO in stand-by mode which fewer than 1mA for high efficiency.

• 전자공학회논문지 IE
• /
• v.45 no.1
• /
• pp.31-37
• /
• 2008

A Wibro RF down converter of 2.3GHz band is designed and implemented in this paper. The problems that can occur in the receiver LNA(Low Noise Amplifier) to minimize additional purposes. In addition, 2.3GHz band from the 75 MHz downward to minimize the losses in the process, transform and improve efficiency, and achieve stable characteristics can be used to make high frequency characteristics of the device. Wibro repeater uses a TDMA(Time Division Multiplexing Access) method is needed because the RF switch. Production criterion specification, the input voltage from +8 V 1.2A of current consumption, 60dB gain and the noise figure of less than 2.5dB, VSWR(Voltage Standing Wave Ratio) less than 1.5, more than IMD(Inter Modulation Distortion) 60dB satisfied. Environmental conditions ($-20^{\circ}C$ to $70^{\circ}C$) to pass the test of reliability in a long time, that seemed crafted Wibro down converter be applied to the Wibro repeater.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.4
• /
• pp.457-463
• /
• 2012

Current refrigerators are designed to have thin doors and walls to facilitate user convenience and increase inner storage space. However, the thin doors and walls gives rise to the problem of dew generation on the outer surface of a refrigerator due to a large critical temperature difference between the outer wall and the room air; So far, an electric heater is commonly used for making the dew to evaporate; in this case, the heater inevitably requires additional electrical power. We propose a new approach to reduce the dew generation in a refrigerator by redesigning the gasket and varying the thickness of the inner case of the refrigerator. The results of simulations performed in this study indicate that the surface temperature in the region where dew was generated was increased by approximately $0.39{\sim}3.07^{\circ}C$ without the use of a heater.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.1
• /
• pp.137-142
• /
• 2014

Industrial control system (ICS) is a computer based system which are typically used in nation-wide critical infra-structure facilities such as electrical, gas, water, wastewater, oil and transportation. In addition, ICS is essentially used in industrial application domain to effectively monitor and control the remotely scattered systems. The highly developed information technology (IT) and related network techniques are continually adapted into domains of industrial control system. However, industrial control system is confronted significant side-effects, which ICS is exposed to prevalent cyber threats typically found in IT environments. Therefore, cyber security vulnerabilities and possibilities of cyber incidents are dramatically increased in industrial control system. The vulnerabilities that may be found in typical ICS are grouped into Policy and Procedure, Platform, and Network categories to assist in determining optimal mitigation strategies. The order of these vulnerabilities does not necessarily reflect any priority in terms of likelihood of occurrence or severity of impact. Firstly, corporate security policy can reduce vulnerabilities by mandating conduct such as password usage and maintenance or requirements for connecting modems to ICS. Secondly, platfom vulnerabilities can be mitigated through various security controls, such as OS and application patching, physical access control, and security software. Thirdly, network vulnerabilities can be eliminated or mitigated through various security controls, such as defense-in-depth network design, encrypting network communication, restricting network traffic flows, and providing physical access control for network components.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.12
• /
• pp.54-60
• /
• 2007

This paper proposes a built-in-self-repair (BISR) structure using 2-dimensional spare memory to effectively self-repair faults of an embedded memory. In case of multiple faults in the same row (column) of an embedded memory, the previous method using 1-D spare column (row) memory needs the same number of spare memory columns (rows) as the number of faults to self-repair them. while the new method using 2-D spare memory needs only one spare row (column) to self-repair them. Also, the virtual divided memory is adopted to be able to self-repair using not a full spare column memory but the only partial spare column memory corresponding to the faults. A self-repair circuit with $64\times1-bit$ core memory and $2\times8$ 2-D spare memory is designed. And the circuit includes a built-in-self-test block using the 13N March algorithm. The circuit has been implemented using the $0.25{\mu}m$ MagnaChip CMOS process and has $1.1\times0.7mm^2$ chip area with 10,658 transistors.

• Current Photovoltaic Research
• /
• v.8 no.3
• /
• pp.67-78
• /
• 2020

A novel energy production system which has fascinated a wide consideration because of its several benefits that are called floating photovoltaic technology (FPVT). The FPVT system that helps to minimize the evaporation of water as well as an increase in energy production. For the research purposes, both electrical and mechanical structure requires studying of these systems for the development of FPVT power plants. From different points of views, numerous researches have been directed on FPVT systems that have evaluated these systems. The present research article give a logical investigation and up to date review that shows the different features and components of FPVT systems as an energy production system is offered. This articles reviewing the FPVT that gets the attention of the scientists who have the investigational stage and involuntary inspection of FPVT systems in addition to influence of implementing these systems on the water surface. Also, a comprehensive comparison has been constructed that shows the cons and pros of various types of solar systems that could be installed in various locations. In this review, it has been found that solar energy on the roof of a dwelling house generally has a power of 5 to 20 kW, while the inhabitants of commercial buildings generally have a power of 100 kW or more. The average power capacity of a floating solar panel is 11% more of the average capacity of a solar panel installed on the ground. Studies show that 40% of the water in open reservoirs is lost through evaporation. By covering only 30% of the water surface, evaporation can be reduced by 49%. The global solar panel market exceeds 100 GW and the capacity of 104 GW will bring the annual growth rate to 6%. In 2018, the world's total photovoltaic capacity reached 512 GW, an increase of 27% compared to the total capacity and about 55% of the renewable resources newly created that come from photovoltaic systems. It has been also predicted by this review that in 2025 the Solar technology including the FPVT system will increase by 7.38% that is 485.4 GW more of today installed power worldwide.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.39 no.3
• /
• pp.51-58
• /
• 2002

The conventional code division multiple access(CDMA) detector shows severe degradation in communication quality as the number of users increases due to multiple access interferences(MAI). This problem thus restricts the user capacity. Various multiuser detection algorithms have been proposed to overcome the MAI problem. The existing detectors can be generally classified into one of the two categories : linear multiuser detection and subtractive interference cancellation detectors. In the linear multiuser detection, a linear transform is applied to the soft outputs of the conventional detector. In the subtractive interference cancellation detection, estimates of the interference are generated and subtracted out from the received signal. There has been great interest in the family of the subtractive interference cancellation detection because the linear multiuser detection exhibits the disadvantage of taking matrix inversion operations. The successive interference cancellation (SIC) and the parallel interference cancellation (PIC) are the two most popular structures in the subtractive interference cancellation detector. The SIC structure is very simple in hardware complexity, but has the disadvantage of increased processing delay time, while the PIC structure is good in performance, but shows the disadvantage of increased hardware complexity. In this paper we propose a mixed structure form of SIC and PIC in order to achieve good performance as well as simple hardware complexity. A performance analysis of the proposed scheme has been made, and the superior characteristics of the mixed structure are demonstrated by extensive computer simulations. 

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.12
• /
• pp.1071-1086
• /
• 2016

The safety of aircraft can be threatened by environmental factors, such as icing, turbulence, and lightning strike. Due to its adverse effects on aircraft structure and electronic components of aircraft, lightning strike is one of the biggest hazards on aircraft safety. Lightning strike can inject high voltage electric current to the aircraft, which may generate strong magnetic field and extreme hot spots, leading to severe damage of structure or other equipment in aircraft. In this work, mechanism of lightning strike and associated direct and indirect effects of lightning on aircraft were studied. First, on the basis of aircraft lightning regulations provided by Aerospace Recommended Practice (ARP), we considered different lightning waveform and zones of an aircraft. A coupled thermal-electrical computational model of ABAQUS was then used for simulating flow of heat and electric current caused by a lightning strike. A study on fuel tank, with and without lightning protection system, was also conducted using the computational model. Finally, electric current flow on two full scale airframes was analyzed using the EMA3D code.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.1
• /
• pp.111-116
• /
• 2017

We propose the compact circular polarized antenna. The radiation elements of the proposed antenna is designed using FR4 substrate with the size of $25mm{\times}3.2mm{\times}5mm$ and stand on four corners of the feed network substrate. The feeder network is designed on FR4 substrate with the size of $40mm{\times}40mm{\times}0.8mm$ and has four oupt signals with same magnitude and $90^{\circ}$ phase difference. The input impedances of the designed radiation elements and the output impedances of the feeder network are $100{\Omega}$. The designed antenna has the dimension of $40mm{\times}40mm{\times}5.8mm$ and the operated frequency band of 1.559 - 1.609 GHz. The fabricated antenna has RHCP radiation pattern and the measured results of axial ratio less than 3.5 dB and radiated gain more than 1.5 dBic. The fabricated antenna can apply to GLONASS and Beiodu systems as well as GPS system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.11
• /
• pp.1193-1203
• /
• 2008

An active antenna(AA) can have wider bandwidth and more gain with small antenna size than those of passive antennas. However, AA inherently generates thermal noise and spurious signals from an active device. Moreover, the spurious performance of AA is very important in a highly sensitive receiving system since it is located at the front end of the receiving system. In this study, we developed an AA with $100{\sim}500\;MHz$, having the output P1dB higher than 3 dBm and little spurious signals in real environments. To achieve such performance, we designed an AA with 3-stage amplifier using CD(common drain) FET and 2 BJTs. Its electrical performances were simulated using ADS. The measurement results for typical gain, NF, OIP3, VSWR and P1dB in the required frequency band were 9.7 dBi, 10 dB, 14 dBm, 1.7:1 and 3 dBm respectively. They are in good agreement with simulation results. The unwanted spectrum level of the proposed AA is $10{\sim}30\;dB$ lower than that of the antenna with CS(common source) FET configuration at a west suburban area of Seoul, which shows that the proposed AA can be applicable to a highly sensitive receiving system for detecting unknown weak signals mixed with broadcasting and civilian communication signals.