• Resources Recycling
• /
• v.25 no.6
• /
• pp.13-22
• /
• 2016

This study is aimed at compare and evaluate the environmental impact of End-of-Life Vehicle(ELV) on the eco-friendly technology dismantling and recycling system, using Life Cycle Assessment (LCA) method. In this study, it was analyzed for the environmental impacts of raw materials, disassemble process, recycle parts separation and waste treatment into the process of ELV treatment by greenhouse gas and resource consumption, etc. Through this study, the indoor rail type dismantling technology were recycling rate applied on the alternate system was increased by approximately 8%. As a result, it was 3 to 88% by improving the environmental impact category. In addition, the added benefit of approximately 8 - 62% in pre-market occurred through the recycling rate, improve parts reuse rate of ELV. Through the results of this study, legal compliance, improved reuse and recycling ratio, used parts market reach, enable exports has identified the need for the effort that the dissemination and diffusion of eco-friendly technology.

• Clean Technology
• /
• v.23 no.1
• /
• pp.15-26
• /
• 2017

The recycling process of ELV consists of three phases: dismantling, shredding and ASR treatment. Dismantling is the collection of reusable parts and the most important phase. The types of dismantling system is diverse and each country has different characteristics. Therefore, the selection of a suitable ELV dismantling system for a target country is dependent on the characteristics of each country. But the characteristics of country data changes every year and is insufficient and ambiguous. In this study, fuzzy inference and modified QFD (Quality function deployment) methods are utilized to solve the problems. The fuzzification of characteristics data for each country, customized rules and decision of modified QFD matrix are developed, which is applied to sample countries.

• Resources Recycling
• /
• v.21 no.4
• /
• pp.69-75
• /
• 2012

Destruction of HFC-134a from ELV (End of Life Vehicle) were determined in a gasification-melting demonstration system of municipal solid waste (100ton/day). The injection system has been developed for the uniform injection of HFC-134a to the gasification-melting system. The destruction characteristics of HFC-134a and analysis of exhaust gases have been performed. The destruction efficiency was 99.995% for HFC-134a feeding of 3 kg/hr and the exhaust gases such as CO, SOx, NOx, HCl and HF satisfied the environmental standards.

• Clean Technology
• /
• v.18 no.4
• /
• pp.373-378
• /
• 2012

The end-of-life vehicles (ELV) are important recycling sources, and there are several stages involved in the recycling such as dismantling, shredding, and treatment of shredder residues (ASR). The legal recycling rate should be at least 95% on and after 2015, while we need a proper system to monitor recycling of ELV components and to calculate the practical recycling rate. The paper suggests a monitoring system that calculates practical recycling rates of dismantled components by use of a database of standard recycling rate as well as a web-based monitoring, which is linked to the Eco Assurance system for electric & electronic equipment and vehicle (EcoAS). Also the system supports dismantling and monitoring process by incorporating a standard vehicular component database, which facilitates recording dismantled weight data but also monitoring of dismantled components.

• Resources Recycling
• /
• v.20 no.1
• /
• pp.14-27
• /
• 2011

In order to review the End-of Life Vehicle(ELV) recycling system and recycling business of dismantlers in Japan, scheme of the automobile recycling law, status of ELV recycling, exports of used cars, ELV marketing business of dismantler and upgrading of used parts net work were studied. On the other hand, field survey in details for dismantling works were conducted at West-Japan Auto Recycling Co.. Although the ELV recycling system has been operating smoothly without any noticeable trouble, recycling business is running under severe circumstance. Exports of used cars have been increasing day by day through worldwide 176 countries. Finally, reuse parts of ELV concerning innovation marketing was discussed.

• Resources Recycling
• /
• v.18 no.5
• /
• pp.3-11
• /
• 2009

Recently efficient recycling of natural resource has been raised many people's interest with global warming issue. This study is focused mainly on main content of automobile recycling regulation and current situation of each nations including EU which is firstly acted. Also we were considering for adequate way to make better resource recycling condition and reduce Environment burden.

• Journal of Welding and Joining
• /
• v.32 no.3
• /
• pp.74-80
• /
• 2014

Due to environmental regulations (RoHS, WEEE and ELV) of the European Union, electronics and automotive electronics have to eliminate toxic substance from their devices and system. Especially, reliability issue of lead-free solder joint is increasing in car electronics due to ELV (End-of-Life Vehicle) banning from 2016. We have prepared engine control unit (ECU) modules soldered with Sn-40Pb and Sn-3.0Ag-0.5Cu (SAC305) solders, respectively. Degradation characteristics of solder joint strength were compared with various conditions of automobile environment such as cabin and engine room. Thermal cycle test (TC, $-40^{\circ}C$ ~ ($85^{\circ}C$ and $125^{\circ}C$), 1500 cycles) were conducted with automotive company standard. To compare shear strength degradation rate with eutectic and Pb-free solder alloy, we measured shear strength of chip components and its size from cabin and engine ECU modules. Based on the TC test results, finally, we have known the difference of degradation level with solder alloys and use environmental conditions. Solder joints degradation rate of engine room ECU is superior to cabin ECU due to large CTE (coefficient of thermal expansion) mismatch in field condition. Degradation rate of engine room ECU is 50~60% larger than cabin room electronics.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.2
• /
• pp.25-30
• /
• 2018

Sn-Pb solder has been used in automotive electronics for decades. However, recently, due to the environmental and health concerns, some international environmental organizations such as the end-of-life vehicle (ELV) enacted legislation banning of the Pb usage in automotive electronics. For this reason, many studies to develop and promote Pb-free soldering have been significantly reported. Meanwhile, because of flexibility and lightweight, flexible printed circuit boards (FPCBs) have been increasingly used in automotive electronics for lightweight to improve fuel efficiency and space utilization. Although the properties of lead-free solders for automotive electronics have been widely studied, there is a lack of research on the reliability performance of the lead-free solder joint on FPCB under user conditions. This study reported the properties of solder joints between Pb-free solders such as Sn3.0Ag0.5Cu, Sn0.7Cu and Sn0.5Cu0.01Al (Si), and various FPCBs finished with organic solderability preservative (OSP) and electroless nickel immersion gold (ENIG). To evaluate on joint properties and reliabilities with different solder compositions and surface-finishing materials, pull strength test, thermal shock test, and bending cycle test were performed and analyzed. After the bending cycle test of solder joint on OSP-finishing, the fractures were occurred in solder and the lifetime of Sn3.0Ag0.5Cu solder joint was the longest.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.1
• /
• pp.17-25
• /
• 2017

Recently, research and application for a power module have been actively studied according to the increasing demand for the production of vehicles, smartphones and semiconductor devices. The power modules based on the transient liquid phase (TLP) technology for bonding of power semiconductor devices have been introduced in this paper. The TLP bonding has been widely used in semiconductor packaging industry due to inhibiting conventional Pb-base solder by the regulation of end of life vehicle (ELV) and restriction of hazardous substances (RoHS). In TLP bonding, the melting temperature of a joint layer becomes higher than bonding temperature and it is cost-effective technology than conventional Ag sintering process. In this paper, a variety of TLP bonding technologies and their characteristics for bonding of power module have been described.

• Resources Recycling
• /
• v.28 no.2
• /
• pp.23-30
• /
• 2019

An color sorting technique was introduced to recycle End-of-life automobile shredded bumpers. The color sorting is a innovate method of separating the differences in the color of materials which are difficult to separate in gravity and size classification by using a camera and an image process technique. Experiments were planned and optimal conditions were derived by applying BBD (Box-Behnken Design) in the reaction surface method. The effects of color sensitivity, feed rate and sample size were analyzed, and a second-order reaction model was obtained based on the analysis of regression and statistical methods and $R^2$ and p-value were 99.56% and < 0.001. Optimum recovery was 94.1% under the conditions of color sensitivity, feed rate and particle size of 32%, 200 kg/h, and 33 mm respectively. The recovery of actual experiment was 93.8%. The experimental data agreed well with the predicted value and confirmed that the model was appropriate.