• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.6
• /
• pp.408-420
• /
• 2003

This paper describes a Delay Locked Loop (DLL) circuit having two advancements : 1) a dual loop operation for a wide lock-range and 2) programmable replica delays using antifuse circuitry and internal voltage generator for a post-package skew calibration. The dual loop operation uses information from the initial time-difference between reference clock and internal clock to select one of the differential internal loops. This increases the lock-range of the DLL to the lower frequency. In addition, incorporation with the programmable replica delay using antifuse circuitry and internal voltage generator allows for the elimination of skews between external clock and internal clock that occur from on and off-chip variations after the package process. The proposed DLL, fabricated on 0.16m process, operates over the wide range of 42MHz - 400MHz with 2.3v power supply. The measured results show 43psec peak-to-peak jitter and 4.71psec ms jitter consuming 52㎽ at 400MHz.

• Journal of Family Resource Management and Policy Review
• /
• v.20 no.3
• /
• pp.95-113
• /
• 2016

This study investigates the potential for multi-cultural youths, given their innate bilingual and dual culture, to be trained as the competent ODA professionals. For the purpose of collecting information, we organized two different kinds of FGI in 2015. The first FGI was conducted with a group of 10 expert participants from August 17 to September 25. The second FGI was conducted four times, from October 5 to October 23, with 13 adolescents from multi-cultural families from Russia, Mongolia, Vietnam, India, Indonesia, Japan, and China. The semi-structured interview items were passed through a formal review process of the Institutional Ethics Committee. Furthermore, with the participants' pre-consent to recording, all recorded data were categorized through the transcription process. The results are as follows. While the potential for nourishing bilingual and dual cultural capabilities are high for the adolescent children of multi-cultural families, the expert group also emphasized the negative aspects of these capabilities being suppressed due to the relatively oppressed family environment. The expert group therefore suggests the following: building parent awareness of ODA human resources, developing an educational career transition roadmap, and providing institutional incentives for ODA. In addition, to some extent, the researchers were able to detect some positive self-esteem among the adolescent children of multi-cultural families as a result of the bilingual and dual cultural competencies required to be ODA personnel. In sum, the research provides insight into the need for national social support for the adolescent children of multi-cultural families, so that their strengths are not extinguished, in order that they might grow up as competent ODA personnel.

• Journal of Venture Innovation
• /
• v.6 no.2
• /
• pp.145-157
• /
• 2023

The present study aimed to examine the relationship between person-job fit, work meaningfulness, job involvement, and career satisfaction, which have recently gained attention from employees and HR professionals. Based on previous studies, we logically established a path from person-job fit to work meaningfulness, job involvement, and ultimately career satisfaction. This study sought to validate these dual mediating effect. A survey was conducted with 283 employees, and the data were analyzed using SPSS 21 and Process Macro. The main findings of the study are as follows: person-job fit, work meaningfulness, job involvement, and career satisfaction showed positive correlations. The dual mediating effects of work meaningfulness and job involvement on the relationship between person-job fit and career satisfaction were statistically significant. These results imply that in order to prevent employee turnover and ensure the organization's sustained performance, it is necessary to design jobs in a way that allows employees to perceive their work as suitable and aligned with their characteristics, thereby enhancing positive psychological factors such as work meaningfulness, job involvement, and career satisfaction. The conclusions provide implications, limitations, and suggestions for future research.

• Proceedings of the IEEK Conference
• /
• 2004.08c
• /
• pp.796-800
• /
• 2004

The main research on this paper is to model on-chip inductor in digital CMOS technology by using the foundry parameters and the physical structure. The s-parameters of a spiral inductor are extracted from the modeled equivalent circuit and then compared to the results obtained from HFSS. The structure and material of the inductor used for modeling in this work is identical with those of the inductor fabricated by CMOS process. To show why the modeled inductor instead of ideal inductor should be used to design a RF system, we designed dual band RF front-end receiver and then compared the results between when using the ideal inductor and using the modeled inductor.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.215.2-215.2
• /
• 2015

We fabricated dual active layer (DAL) thin film transistors (TFTs) with indium tin zinc oxide (ITZO) and indium gallium zinc oxide (IGZO) thin film layers using solution process. The ITZO and IGZO layer were used as the front and back channel, respectively. In order to investigate the bias stress stability of ITZO SAL (single active layer) and ITZO/IGZO DAL TFT, a gate bias stress of 10 V was applied for 1500 s under the dark condition. The SAL TFT composed of ITZO layer shows a poor positive bias stability of ${\delta}VTH$ of 13.7 V, whereas ${\delta}VTH$ of ITZO/IGZO DAL TFT was very small as 2.6 V. In order to find out the evidence of improved bias stress stability, we calculated the total trap density NT near the channel/gate insulator interface. The calculated NT of DAL and SAL TFT were $4.59{\times}10^{11}$ and $2.03{\times}10^{11}cm^{-2}$, respectively. The reason for improved bias stress stability is due to the reduction of defect sites such as pin-hole and pores in the active layer.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.269-273
• /
• 2003

There is a growing interest to replace the commercial steels with non-heat treated steels, which does not involve the spheroidization and quenching-tempering treatment. However, Non-heat treated steels should satisfy high strength and good formability without performing heat treatment. Therefore, it is important to investigate optimum materials showing a good combination of strength and formability after the drawing process. In this study, Dual-Phase Steels were studied as candidate materials for non-heat treated steels, which have different martensite morphologies and volume fractions obtained through heat-treatment of intercritical quenching (IcQ), intermediate quenching (ImQ) and step quenching (SQ). The mechanical properties of DP steels were measured by tension and compression tests. Also, the cold formability of three DP steels which have similar tensile strength value was investigated by estimating the deformation resistance and the forming limit. The deformation resistance which is important factor in determining die life was estimated by calculating the deformation energy. And the forming limit was estimated by measuring the critical strain revealing crack initiation at the notch tip of the specimens.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.1
• /
• pp.84-92
• /
• 2015

Fillers have been used to improve the optical and printing properties and to reduce the production cost while increasing the filler content in paper causes adverse effects on paper strength. In the previous study, it was shown that the thick stock addition of filler can increase the filler content without significantly sacrificing paper strength. This study was carried out to elucidate the effect of the location of starch addition (before or after the filler addition) on handsheet properties and a papermaking process as a part of developing the thick stock loading technology. In addition, effects of dual flow addition of cationic starch were evaluated. It was found that paper strength was superior when cationic starch was added after the filler addition. No adverse effects on optical properties, formation and filler retention were observed. Drainage was a bit slower when starch was added after the filler addition, which shall be resolved with regulating other factors. Dual flow addition of cationic starch before and after filler addition did not show any special advantage.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.1
• /
• pp.110-119
• /
• 2017

This paper describes a CMOS image sensor (CIS) with dual correlated double sampling (CDS) and column-parallel analog-to-digital converter (ADC) and its measurement method using a field-programmable gate array (FPGA) integrated module. The CIS is composed of a $320{\times}240$ pixel array with $3.2{\mu}m{\times}3.2{\mu}m$ pixels and column-parallel 10-bit single-slope ADCs. It is fabricated in a $0.11-{\mu}m$ CIS process, and consumes 49.2 mW from 1.5 V and 3.3 V power supplies while operating at 6.25 MHz. The measured dynamic range is 53.72 dB, and the total and column fixed pattern noise in a dark condition are 0.10% and 0.029%. The maximum integral nonlinearity and the differential nonlinearity of the ADC are +1.15 / -1.74 LSB and +0.63 / -0.56 LSB, respectively.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.10
• /
• pp.79-86
• /
• 2004

This paper proposes a dual band Voltage Controlled Oscillator(VCO) with a standard 0.3${\mu}{\textrm}{m}$ CMOS process to generate 1.07GHz and 2.07GHz. The proposed VCO architecture with 50% duty cycle circuit and a half adder(HA) was capable of producing a frequency two times higher than that of the conventional VCOs. The measurement results demonstrate that the gain of VCO and power dissipation are 561MHz/V and 14.6mW, respectively. The phase noises of the dual band VCO are measured to be -102.55dBc/Hz and -95.88dBc/Hz at 2MHz offset from 1.07GHz and 2.07GHz, respectively.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.118-121
• /
• 2007

수소 스테이션의 수소분리정제를 위한 Compact 형 PSA를 연구하였다. 수소 스테이션의 공정과정 중에서 수소 분리를 위한 PSA 장치는 에너지효율면에서 장점을 가지고 있지만 부피가 커서 많은 부지를 차지하는 단점이 있다. 수소 PSA의 이러한 단점을 줄이기 위하여 하나의 흡착탑 안에 다른 흡착탑을 넣는 Dual bed 형태의 Compact형 수소 PSA공정을 연구하였다. Compact형 수소 PSA는 하나의 bed안에 다른 하나의 bed를 넣음으로써 시스템이 차지하는 부피를 줄이는 한편, inner bed와 outer bed사이의 열교환 효과가 나타나기 때문에 그 효율을 높일 수가 있다. Compact형 Dual bed는 활성탄으로 충진하였고 공급 기체로는 4성분 수소 혼합물 ($H_2/CO/CH_4/CO_2$, 69:2:3:26 vol.%)를 사용하였다. 흡착탑의 동특성을 알아보기 위하여 공급유량 7LPM, 흡착압력 9atm의 조건으로 파괴 실험을 수행하였다. 또한, Compact형 흡착탑의 열교환 효과가 PSA공정에 미치는 영향을 보고자 한 쪽 탑에서 흡착을 할 때, 다른 탑에서 탈착이 일어나는 실험을 하였다. 그리고 P/F ratio에 따라 Compact형 PSA 공정 실험을 하고 Compact형 흡착탑과 같은 부피의 일반 두 탑 PSA 공정을 시뮬레이션 값과 비교함으로써 Compact형 PSA의 성능을 알아 보았다. 그 결과 Dual bed PSA는 작은 부피를 차지하는 장점뿐만 아니라 열적 효과로 인하여 기존의 단일 흡착탑 PSA에 비하여 보다 높은 효율을 나타내면서 우수한 수소 분리 성능을 보여주었다.