• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.527-529
• /
• 1987

This paper presents a study on the driving characteristics or delta inverter driving induction motor control systems based on the microprocessor. Delta inverter is a novel circuit which uses only three power transistor. Requiring approximately hair the components or a conventional bridge inverter it therefore has a merit of coat and Simplicity. The basic operating principles of the delta inverter and conventional bridge inverter are argued, using resistive and inductive load. Sinusoidal PWM method uses to reduce the harmonic components of its output waveform to acceptable levels.

• Proceedings of the IEEK Conference
• /
• 2002.07c
• /
• pp.1390-1393
• /
• 2002

Comparative analysis of driving inverters for piezo-electric transformer (PT) is performed and the suit- able drive circuit for portable devices such as personal digital assistants (PDA) is chosen with the experiment in this paper. As a result, a single-switch inverter with a small two winding reactor is chosen, and then the advantages of this method are clarified. It is also confirmed that the driving inverter with this method enables to realize a stabilized AC 400v output and 82% power efficiency from DC 3V input under the conditions of the variations of load current or input voltage from the experiments. Piezo-electric Transformer, Back-Light System, Single-Switch Driving Circuits, Control Method

• Journal of Drive and Control
• /
• v.17 no.4
• /
• pp.38-45
• /
• 2020

The purpose of this study was to analyze the design sensitivity of an independent driving system for disaster response. The research procedure was as follows. First, an analysis model based on the circuit diagram of the driving system was developed. Second, to ensure the reliability of the analytical model, the load-free test results and analysis results were compared. Even if different loads acted on four independent motors, the system was confirmed to be implemented according to the design intent. Finally, the design variables of the analysis model were analyzed to obtain design variables with a significant impact on system performance and stability. The analysis program used simulation X.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.3
• /
• pp.39-46
• /
• 1994

CMOS LCD driving circuits using poly-Si TFT have been designed and basic blocks including test patterns have been fabricated. Column driver drives the pixels by block because polu-Si TFT can not operate at the speed of video signal. Row driver has mode selection circuit which can select a mode between interlacing mode and non-interlacing mode. Experimental results show shift register can operate at 1MHz colck frequency with 4pF load.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.10
• /
• pp.35-42
• /
• 1995

In this paper the driving-condition-dependent optical transmission characteristics of an STN LCD are studied. The optical transmission properties are measured for the applied voltage waveform is varied. Also, the optimum ranges of the M signal frequency and the frame frequency are investigated. An LCD is modeled by the equivalent circuit to study the effect of the parameter variation on the frequency response.

• Proceedings of the KIEE Conference
• /
• 2000.11c
• /
• pp.428-430
• /
• 2000

In this paper, the Flexible information display was implemented using AC powder electroluminescent device. ZnS:Cu and $BaTiO_3$ was used as a phosphor and dielectric respectively. The preparation of phosphor and dielectric layer was performed with screen printing. The implemented system of the Flexible information display was divided as following; EL display, driving circuit, software for driving. The properties of fabricated devices was measured with EL spectrum and brightness.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.10
• /
• pp.197-203
• /
• 2014

The safety and arming device(SAD), one of the components of the fuzes, shall provide safety that is consistent with handling, storage, transportation, use, and disposal. In this paper, we describes the design of the SAD which includes the solenoid assembly and the solenoid driving circuit to improve the safety of the fuzes. The solenoid assembly consists of a coil assembly, a restoring spring, and a core. The solenoid assembly is added in the SAD as an additional safety device. In case of the normal circumstances, the core of the solenoid assembly restrains the $1^{st}$ and $2^{nd}$ safety devices of the SAD for those devices not to operate at all, so that the SAD can secure safety for storage, transportation, and use. In contrast, when the battery power is provided to the solenoid driving circuit just before the flight, the core confirms the power level and starts removing the restraint from the $1^{st}$ and $2^{nd}$ safety devices of the SAD, and then the SAD is able to change its mode from safety mode to armed mode. After firing, once the SAD's operations complete, the turned-on arming switch stops providing the power to the solenoid assembly automatically. It can reduce the power consumption at solenoid assembly. Therefore, the proposed solenoid driving circuit for the solenoid assembly not only unlocks the restrained solenoid assembly from the safety devices, but also saves the power consumption during the flight.

• Proceedings of the IEEK Conference
• /
• 2003.07c
• /
• pp.2847-2850
• /
• 2003

A input voltage conversion dimming control formula and a PMW dimming control formula which have been used for dimming control of CCFL driving inverter in TFT-LCD backlight, are the existing facilities so far, however, in this thesis the circuit is designed by applying The rover inverter that are able to measure output brightness according to changing of duty ratio at PWM and voltage. consequently, it's able to be confirmed that we can have dimming control more detailed than before.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.69-74
• /
• 2004

System-on-glass technology made with low temperature poly-Si TFT has been rapidly advancing in recent years. We have developed a low-power, narrow edged frame, 1.9inch system-on-glass LCD which fully integrates a 16-bit RGB interface driver and all power circuits required for driving the LCD. In this paper, the latest poly-Si TFT circuit technologies used in the newly developed LCD are discussed. The development trends are also reviewed.

• Proceedings of the IEEK Conference
• /
• 2003.11a
• /
• pp.343-346
• /
• 2003

In this paper, we try to make a systematic analysis for the vertical crosstalk on LCD driving. The vertical Crosstalk is one of the inevitable phenomena in the high-resolution TFT-LCDs. At first, the vortical Crosstalk is defined. Considering the structure of the pixels and data lines, a LCD (a pixel) is modeled electrically by its' equivalent circuit. The circuit is verified by experiment and used to find the cause of the vertical Crosstalk.