• Fire Science and Engineering
• /
• v.30 no.3
• /
• pp.86-93
• /
• 2016

The effects of the shape of a drencher head on the flow characteristics and radiation attenuation of a water curtain, in order to prevent a fire spread, were experimentally studied. The distance (h) between the orifice exit and deflector and the diameter of deflector (D) were varied as the shape factors of the head, with the same orifice diameter (d). It was found that an increase in h leads to an increase in the water flow rate and spray angle. However, the change in the spray angle decreases with increasing D. Increasing D brings about a subtle increase in the water flow rate and a significant decrease in the spray angle. A larger value of D makes it possible to produce a flatter pattern of the water curtain, but reduces the uniformity of the droplets inside the spray angle. The mean droplet diameter decreases significantly as the operating pressure increases. However, the variation in the shape of the drencher head does not significantly affect the change in the mean diameter at the same operating pressure. Finally, it was found that the radiation attenuation afforded by the water curtain at the same operating pressure was affected by water flow rate and droplet uniformity, which were determined by h and D, respectively.

• Journal of Korean Society of Disaster and Security
• /
• v.16 no.4
• /
• pp.1-7
• /
• 2023

The purpose of this study is an experimental research to investigate the effectiveness of debris flow reduction structures when a debris flow disaster occurs on a steep slope. The control structure for debris flow took the form of baffle, and the soil deposition area and soil runout distance due to debris flow from the downstream were investigated according to the installation number of baffle and each specification. As the slope of the channel became steeper, the sediment deposition area and runout distance increased, and as the sediment volume concentration decreased, the sediment deposition area and runout distance increased. When the sediment concentration was low, differences appeared depending on the slope of the channel because the debris flow had a high liquid content. Overall, the larger the sediment volume concentration, the greater the decrease in sediment deposition area and soil runout distance. As the number of baffles increases, the soil deposition area and runout decrease, showing that the baffles have the ability to control debris flows. The results of this research will provide good information when installing attenuation or control structures when sediment disasters occur in steep slopes.

• Journal of Environmental Health Sciences
• /
• v.34 no.5
• /
• pp.395-402
• /
• 2008

Road traffic noise causes considerable disturbance and annoyance in exposed inhabitants. Particularly, arterial road noise is a significant environmental problem in many urban areas in which higher traffic volume and higher car speed occur. Arterial road noise became the target of this investigation in Seoul, South Korea. Noise levels were measured at four points that were based on distance from roadside at the same measurement site and under the conditions as reported by the National Institute of Environmental Research (NIER) in 1999. The average noise levels ($L_{eq,1h}$) of the arterial road was 80.3 dBA at 5 m, 77.4 dBA at 10 m, 73.7 dBA at 20 m, 70.9 dBA at 30 m. A comparison between 1999 and 2008's measurement values has shown that in 2008 noise level is up by about 1.5 dBA, traffic volume has increased by about 15.7%, while car speed has decrease by about 8%. The relationship between 2008' measured values and predicted values using the NIER Equation is low under 10 m from the roadside. The influence range of arterial noise is calculated at 26 m for road noise limits in daytime. In relation to the comparison between traffic volume and noise level, the equivalence in traffic volume (Light car+10xHeavy car) is higher than other variables.

• Explosives and Blasting
• /
• v.17 no.2
• /
• pp.36-44
• /
• 1999

A study was made on the design of the prediction model concerning blasting vibration in a constraction site, Namgu, Daegu City. The geology in this area consists of hornfels of shale and mud underlain by quartize, of which the main strike of the geological structure is NW direction. Measurements were carried out on the top of the wall concrete water storage tank, which is burried in the ground earth. The attenuation due to the vertical wall of the concrete structure may be experted because of spherical divergency at the bottom corner of the wall by the Huygens principle. For design of blasting prediction model, thus among scaled distance(SD) may be preferable to use in the regression model, since they represents most likely the average ground condition. Judging from the regression results, the cube root method may be more suitable for this area. The SD values for the maximum allowable vibration velocity of 0.5 cm/s, in this area are 22.5, 28.0 and 30.6 for the significance level of 50%, 95% and 99%, respectively.

• Explosives and Blasting
• /
• v.21 no.4
• /
• pp.11-21
• /
• 2003

An experimental study was carried out in order to reduce the period and cost of construction of Missiryung tunnel, which is a relatively long one 3.6 km long. An allowable vibration level for curing concrete was established based on the extensive case studies done over the world. and assessment was performed on the possibility of constructing concrete structures like lining during tunnel blasting. Attenuation relationships were obtained by processing more than 130 measurement data from a series of tunnel blasting in the site. A Guideline for safe construction work was suggested. To verification, low small concrete blocks with a constant standoff distance were installed in the floor of the tunnel After the blocks were exposed to blast vibrations for 28 days, compressive strength tests were performed on 20 specimens taken from the blocks. It was shown that the suggested guideline was appropriate for the safe construction work at the site.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.4
• /
• pp.736-742
• /
• 2003

This paper presents the propagation path loss in a tunnel which is a kinds of underground environments. To predict propagation path loss more accurately, we choose a straight tunnel with rectangular cross-section. The simulated receiver powers that are using a hybrid waveguide model and a Ray-Tracing method, are compared with the measured ones as a function of distance between TX and RX antennas in tunnel. The attenuation value of regression analysis for measured power in the tunnel is 0.0238dB/m which is similar to the one of the EH1.2 mode, 0.0246dB/m in hybrid waveguide model. By comparing simulation with measurement in tunnels, it has been shown that the measured values are approximate to the simulated results of ray-tracing model. In the analysis of wide-band channel characteristics of the tunnel, the more the distance between TX and RX antennas in tunnel increases, RMS delay spread increases and coherence bandwidth decreases.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.4
• /
• pp.344-350
• /
• 2009

The goal of this study is to introduce the theoretical background of acoustic nonlinearity in surface wave and to verify its characteristics by experiments. It has been known by theory that the nonlinear parameter of surface wave is proportional to the ratio of $2^{nd}$ harmonic amplitude and the power of primary component in the propagated surface wave, as like as in bulk waves. In this paper, in order to verify this characteristics we constructed a measurement system using contact angle beam transducers and measured the nonlinear parameter of surface wave in an Aluminum 6061 alloy block specimen while changing the distance of wave propagation and the input amplitude. We also considered the effect of frequency-dependent attenuation to the measurement of nonlinear parameter. Results showed good agreement with the theoretical expectation that the nonlinear parameter should be independent on the input amplitude and linearly dependent on the input amplitude and the $2^{nd}$ harmonic amplitude is linearly dependant on the propagation distance.

• Journal of Satellite, Information and Communications
• /
• v.11 no.3
• /
• pp.80-85
• /
• 2016

In this paper, by comparatively analyzing horn type speaker and line array type speaker developed based on line sound source theory and point sound source theory, we research whether theory is adaptable or not in real. Academically, point sound source is attenuated as much as 6dB in accordance with double distance and line sound source is attenuated as much as 3dB in accordance with double distance. Line array speaker system developed based on line sound source is analyzed by theory of line sound source about occurring small sound pressure attenuation and it is propose of research that array composition of right speaker is selected in accordance with use purpose and environment. For this purpose, we analyze theory of point sound source and line sound source. we analyze parameter value by simulating designed horn type speaker and line array speaker based on theory.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2005.05a
• /
• pp.43-46
• /
• 2005

The local magnitude scales yield in the Southern Korean Peninsula following the Richter's original definition are reviewed. In order to compare the previous $M_L$ scales, the new distance correction term of $M_L$ scale is derived as $-logA_{0}$ = 1.017log(r/17)+0.00028(r-17)2+2.0 using broadband velocity seismograms from 126 local events occured from 2000 to 2004. The attenuation rate of this formula fall between those of western and eastern North America. This result is in nearly accord with the $M_L$ scales proposed by Kim and Park(2002). The differences between various $M_L$ scales is owing to insufficient seismic data not to distribute whole area of Southern Korea

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.6
• /
• pp.723-729
• /
• 2014

When the bluetooth technology of smartphone is applied to a remote control system, communication errors caused by wave attenuation and interference results in the shortening of communication distance, loss of the target device control and malfunctioning. In this study, we propose a method to adopt a retransmission persistence controlled S/W ARQ in bluetooth communication to minimize the effect of the communication failure and to detect and handle the state where the target device gets lost control. We implemented a motor-driven RC car equpped with a bluetooth communication module and a steering application program on smartphone to test the proposed method. The experiments are conducted in three communication environments, and have resulted in the increase of the communication distance by at least 30% when S/W ARQ is applied. Moreover, when the communication was disrupted due to environmental disturbances, the S/W ARQ based system stopped immediately any undergoing operations to avoid possible malfunction.