• ETRI Journal
• /
• v.27 no.5
• /
• pp.579-584
• /
• 2005

A CMOS direct-conversion mixer with a single transistor-level topology is proposed in this paper. Since the single transistor-level topology needs smaller supply voltage than the conventional Gilbert-cell topology, the proposed mixer structure is suitable for a low power and highly integrated RF system-on-a-chip (SoC). The proposed direct-conversion mixer is designed for the multi-band ultra-wideband (UWB) system covering from 3 to 7 GHz. The conversion gain and input P1dB of the mixer are about 3 dB and -10 dBm, respectively, with multi-band RF signals. The mixer consumes 4.3 mA under a 1.8 V supply voltage.

• 한국정보통신설비학회:학술대회논문집
• /
• 2007.08a
• /
• pp.7-10
• /
• 2007

최근 이동통신을 이용해 다양한 서비스를 제공하기 위하여 멀티 밴드, 멀티 채널의 송수신기를 단일칩화 하기 위한 연구가 활발히 진행되고 있다. CMOS 집적 회로 기술은 가격 경쟁력이 높고 집적도가 높아 멀티 밴드, 멀티 채널 송수신기를 집적화하기에 적합하다. 그러나 0.18 ${\mu}m$ 이하의 채널 길이를 갖는 CMOS 집적 회로는 1.8 V 이하의 낮은 공급 전압을 제공함으로 높은 이득을 갖는 mixer의 구현이 어렵고, mixer에서 발생되는 2, 3차 상호 변조에 의한 왜곡으로 선형성이 문제가 된다. 이런 문제점을 해결하기 위해서 기능성 능동부하를 적용하여 선형성을 향상한 Direct Conversion Down Mixer를 설계 분석 하였다.

• Proceedings of the IEEK Conference
• /
• 2000.11a
• /
• pp.361-364
• /
• 2000

One of the problems using DCR(Direct Conversion Receiver) are DC offset, poor channel selectivity. APDP(Anti Parallel Diode Pair) can be good candidate for DCR frequency mixer due to its inherent End harmonic suppression. APDP shows good IP2 and DC suppression. This paper describe single APDP LO power characteristics, IP2, and receiver structure utilizing APDP frequency mixer

• Journal of electromagnetic engineering and science
• /
• v.8 no.3
• /
• pp.91-95
• /
• 2008

This paper presents a direct-conversion I/Q up-mixer block, which supports $3{\sim}5$ GHz ultra-wideband(UWB) applications. It consists of a VI converter, a double-balanced mixer, a RF amplifier, and a differential-to-single signal converter. To achieve wideband characteristics over $3{\sim}5$ GHz frequency range, the double-balanced mixer adopts a shunt-peaking load. The proposed RF amplifier can suppress unwanted common-mode input signals with high linearity. The proposed direct-conversion I/Q up-mixer block is implemented using $0.18-{\mu}m$ CMOS technology. The measured results for three channels show a power gain of $-2{\sim}-9$ dB with a gain flatness of 1dB, a maximum output power level of $-7{\sim}-14.5$ dBm, and a output return loss of more than - 8.8 dB. The current consumption of the fabricated chip is 25.2 mA from a 1.8 V power supply.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.6
• /
• pp.1269-1276
• /
• 2005

In this paper, Mixer using the direct-conversion method intended to use in front-end of a RF receiver is designed. The direct conversion Mixer is an alternative wireless receiver architecture to the well-established superheterodyne, particularly for high integration, low power, and low cost. It operates at 2.4GHz band, and is designed and simulated with a 0.35um CMOS technology and HSPICE simulator. Layout is implemented with a Mentor IC Station. The 2.4GHz CMOS Mixer employs a modified single-balanced Gilbert Cell with additional MOSFET in the output stages to improve IIP2, which is a standard of linearity in direct conversion receiver. Additional coversion-stages's transconductances are controlled by each MOSFET's physical properties. The HSPICE simulation results show that the 2.4GHz CMOS Mixer has voltage gam of 29dB, IIP2 of 63dBm, respectively. The Mixer also draws 3.5mA from a 3.3V supply.

• 한국정보통신설비학회:학술대회논문집
• /
• 2008.08a
• /
• pp.414-417
• /
• 2008

This paper presents the design and analysis of 2.45GHz Low-IF Mixer using CMOS 0.18um. The Mixer is implemented by using the Gilbert-type configuration, current bleeding technique, and the resonating technique for the tail capacitance. And the design of this Double Balance Mixer is based on its lineaity since it is important in the interference cancellation system. The low flicker noise mixer is implemented by incorporating a double balanced Gilber-type configuration, the RF leakage-less current bleeding technique, and Cp resonating technique. The proposed mixer has a simulated conversion gain of 16dB a simulated IIP3 of -3.3dBm and P1dB is -19dBm. A simulated noise figure of 6.9dB at l0MHz and a flicker corner frequency of 510kHz while consuming only 10.65mW od DC power. The layout of Mixer for one-chip design in a 0.18-um TSMC process has 0.474mm$\times$0.39 mm size.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.222-226
• /
• 2001

In this paper, 2.4GHz RF Module using Even Harmonic Mixer(EHM) was designed and fabricated for Direct conversion(DC) system. By minimizing performance degradation of DC system with DC offset and LO radiation, the capability of minimization and one chip solution in wireless system was proposed. The designed EHM using anti-parallel diode pair represented 9dB conversion loss and about -60dBm 2LO leakage radiation in RF port, and output reflection and reverse transmission characteristic of low noise amplifier was improved. So superior DC offset suppression characteristic is expected. RF Module which consists of EHM, LNA, RF amplifier, Frequency synthesizer and Duplexer was designed and fabricated.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.9
• /
• pp.825-833
• /
• 2016

This paper introduces a direct-conversion CMOS RF transmitter for the IEEE 802.15.4 standard with a low-power high-gain up-conversion mixer designed in $0.18{\mu}m$ process. The designed RF DCT(Direct Conversion Transmitter) is composed of differential DAC(Digital to Analog Converter), passive low-pass filter, quadrature active mixer and drive amplifier. The most important characteristic in designing RF DCT is to satisfy the 2.4 GHz Zigbee standard in low power. The quadrature active mixer inside the proposed RF DCT provides enough high gain as well as sufficient linearity using a gain boosting technique. The measurement results for the proposed transmitter show very low power consumption of 7.8 mA, output power more than 0 dBm and ACPR (Adjacent Channel Power Ratio) of -30 dBc.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.154-157
• /
• 2000

One of the problems using DCR(Direct Conversion Receiver) type architecture are DC offset, Poor channel selectivity. APDP(Anti Parallel Diode Pair) can be mood candidate for the DCR frequency mixer due to its inherent 2nd harmonic suppression. APDP shows good IP2 and DC suppression. This paper describes single APDP LO power characteristics, IP2, and receiver structure utilizing APDP frequency mixer.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2002.11a
• /
• pp.16-20
• /
• 2002

This paper describes the resistive FET mixer with low IF for the 4-Ch DBF(Digital Beam Forming) receiver with LNA(Low Noise Amplifier). This DBF receiver based on the direct conversion method is generally suitable for high-speed wireless mobile communications. A radio frequency(RF), a local oscillator(LO) and an intermediate frequency(IF) considered in this research are 2.09 ㎓, 2.08 ㎓ and 10㎒, respectively. The RF input power, LO input power and Vgs are used -10㏈m, 6㏈m and -0.4 V, respectively. In the 4-Ch resistive FET mixer with LNA, the measured IF and harmonic components of 10㎒, 20㎒, 2.09㎓ and 4.17㎓ are about -12.5 ㏈m, -57㏈m, -40㏈m and -54㏈m, respectively. The IF output power observed at each channel of 10㎒ is about -12.5㏈m and it is higher 27.5 ㏈m than the maximum harmonic component of 2.09㎓. Each IF output spectrum of the 4-Ch is observed almost same value and it shows a good agreement with the prediction.