• Laser Solutions
• /
• v.7 no.3
• /
• pp.37-46
• /
• 2004

The shape and size variations of the nanopatterns produced on a polymer film using a near-field scanning optical microscope(NSOM) are investigated with respect to the process variables. A cantilever type nanoprobe having a 100nm aperture at the apex of the pyramidal tip is used with the NSOM and a He-Cd laser at a wavelength of 442nm as the illumination source. Patterning characteristics are examined for different laser beam power at the entrance side of the aperture($P_{in}$), scan speed of the piezo stage(V), repeated scanning over the same pattern, and operation modes of the NSOM(DC and AC modes). The pattern size remained almost the same for equal linear energy density. Pattern size decreased for lower laser beam power and greater scan speed, leading to a minimum pattern width of around 50nm at $P_{in}=1.2{\mu}W\;and\;V=12{\mu}m/s$. Direct writing of an arbitrary pattern with a line width of about 150nm was demonstrated to verify the feasibility of this technique for nanomask fabrication. Application on high-density data storage is discussed.

• Journal of the Optical Society of Korea
• /
• v.9 no.1
• /
• pp.16-21
• /
• 2005

Using a cantilever type nanoprobe having a 100㎚m aperture at the apex of the pyramidal tip of a near-field scanning optical microscope (NSOM), nanopatterning of polymer films are conducted. Two different types of polymer, namely a positive photoresist (DPR-i5500) and an azopolymer (Poly disperse orange-3), spincoated on a silicon wafer are used as the substrate. A He-Cd laser with a wavelength of 442㎚ is employed as the illumination source. The optical near-field produced at the tip of the nanoprobe induces a photochemical reaction on the irradiated region, leading to the fabrication of nanostructures below the diffraction limit of the laser light. By controlling the process parameters properly, nanopatterns as small as 100㎚ are produced on both the photoresist and azopolymer samples. The shape and size variations of the nanopatterns are examined with respect to the key process parameters such as laser beam power, irradiation time or scanning speed of the probe, operation modes of the NSOM (DC and AC modes), etc. The characteristic features during the fabrication of ordered structures such as dot or line arrays using NSOM lithography are investigated. Not only the direct writing of nano array structures on the polymer films but also the fabrication of NSOM-written patterns on the silicon substrate were investigated by introducing a passivation layer over the silicon surface. Possible application of thereby developed NSOM lithography technology to the fabrication of data storage is discussed.

• Journal of Sensor Science and Technology
• /
• v.30 no.6
• /
• pp.388-394
• /
• 2021

The conventional microelectromechanical system (MEMS) process has been used to fabricate sensors with high costs and high-volume productions. Emerging 3D printing can utilize various materials and quickly fabricate a product using low-cost equipment rather than traditional manufacturing processes. 3D printing also can produce the sensor using various materials and design its sensing structure with freely optimized shapes. Hence, 3D printing is expected to be a new technology that can produce sensors on-site and respond to on-demand demand by combining it with open platform technology. Therefore, this paper reviews three standard 3D printing technologies, such as Fused Deposition Modeling (FDM), Direct Ink Writing (DIW), and Digital Light Processing (DLP), which can apply to the sensor fabrication process. The review focuses on strain/load sensors having both sensing material features and structural features as well. NCPC (Nano Carbon Piezoresistive Composite) is also introduced as a promising 3D material due to its favorable sensing characteristics.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.530-536
• /
• 2017

The purpose of this study is to specify the procedures in problem design to employ BPBL and to design problems for learning subject content. The design of problems is crucial for the effectiveness of BPBL. Ineffective PBL problems could affect whether students acquire sufficient domain knowledge, activate appropriate prior knowledge, and properly direct their own learning. The procedures for designing good problems are composed of selection of educational content, figuring out the learner's characteristics, finding problems, setting roles and situations, and writing down problems. Using the procedures, we designed five integration problems covering the content of an Internet marketing subject. We can foster talent needed on a current industrial site with BPBL, not whole-class learning in a Mongolian engineering college. We made a plan for the Internet marketing subject based on BPBL in the Mongolian engineering college, and focused on the process of designing problems.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.108-108
• /
• 2007

Inkjet printing is a non-contact and direct writing associated with a computer. In the industrial field, there have been many efforts to utilize the inkjet printing as a new way of manufacturing, especially for electronic devices. The etching resist used in this process is an organic polymer which becomes solidified when exposed to ultraviolet lights and has high viscosity of 300 cPs at ambient temperature. A piezoelectric-driven ink jet printhead is used to dispense $20-40\;{\mu}m$ diameter droplets onto the copper substrate to prevent subsequent etching. In this study, factors affecting the pattern formation such as printing resolution, jetting property, adhesion strength, etching and strip mechanism, UV pinning energy have been investigated. As a result, microscale Etch resist patterning of printed circuit board with tens of ${\mu}m$ high have been fabricated.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.1
• /
• pp.35-40
• /
• 2018

Nd:YAG laser was used to carbonize polyimide films to produce carbon films. This is a simple manufacturing process to fabricate low cost sensors. By applying this method, we studied characteristics of flexible and low-cost piezoresistive. Previously, many studies focused on carbonization of polyimide using $CO_2$ laser with wavelength of $10.6{\mu}m$. In this paper, carbonization (carbonization process) was performed on polyimide films using an Nd:YAG laser with a wavelength of $1.064{\mu}m$. In order to increase the resolution, we optimized the laser conditions of the power density ($W/cm^2$) and the beam scan rate. In previous studies using $CO_2$ laser, the minimum line width was $140{\sim}220{\mu}m$ but in this study, carbon line width was reduced to $35{\sim}40{\mu}m$. The initial sheet resistance of the carbon sensor was $100{\sim}300{\Omega}/{\square}$. The resistance decreased by 30% under stretched with a curvature radius of 21 R. The calculated gauge factor was 56.6. This work offers a simple, highly flexible, and low-cost process to fabricate piezoresistive sensors.

• Journal of Korean Academy of Nursing Administration
• /
• v.1 no.1
• /
• pp.147-211
• /
• 1995

Medication is a kind of medical service and a therapeutic nursing function which takes large portion of nursing service and requires complicated procedures. So many different medical personnel should be involved and cooporate each other in order to accomplish medication. Medication is also a vital nursing service, So nurse feels heavy responsibi lity in that she gives medication to the patient finally, so she has much responsibility if medication error is happened. Therefore it seems very important to clarify the problem of medication system and method, and find the subculture of medication situation because it may promote nursing productivity. The study was conducted to 1. Describe and interpret medication situation. 2. Find out the problem of medication system and method and on alternatives. 3. Compare the medication system and method of hospitals which are located in Seoul with object hospital Ethnographic methodology was used to study medication situation by doing participant observation and interview of health care personnel. Ten nurses and three nurse aids were interviewed. Two residents and internists, two phamacists and two accountants were also interviewed. Data was obtained and analized according to Developmental Research Sequence introduced by Spradly. On the basis of this data the results were as follows. 1. The overall flow of medication system was devided into six stage : first, checking doctor's order : second writing doctor's order, : third, transfering slip into the related departments such as account department, pharmacy : fourth, distribution of medication from pharmacy to unit : fifth, identifing medication by nurses : and finally, medicating to the patient. Behaviorors have been under a lot of stress in that they have to do much works, especially paperworks, So too much time were needed. They also have been suffered interpersonal conflicts among health care personnel and role conflicts in the process of doing medication service. 2. In the process of checking order, the problem was that too much time was required for checking order and paperwork. The more the order changes the more the paperwork is. Nurses have been suffering difficulties in calling internist in order to get bill. Even if writing down slip for medication order is doctor's job, Sometimes nurse has been expected to write slip by doctors or nurse would write slip beacuse of two much complexities and efforts for calling doctors. If the slip were incorrect, much time complicated procedures were more required for correcting it. So delay of administering drug would be resulted consequently. Drugs were delivered from pharmacy to units by delivery agent and phamacist. But because drugs were delivered without arranging room number of patient. Nurse should rearrange drugs in order of the room number So it had made waste time and effort, and Even when emergency drugs were needed, Prompt delivery of drug was not easy because of many reasons. For nurses, it took too long in the identification of the right drug. Actually nurses have heavy burden when medication error happens because nurse is the final actor who gives medication to the patient, So every three shift nurse ought to check drugs as soon as every shift begins. That's why it took too much time due to repeated confirming procedure. When nurses had to go patient room in order to give medications, there were difficulties in watching patient until the patient take medicine correctly. So it was impossible to check every patient wheather he took medicine or not especially in hectic situation. 3. There were many hospitals in Seoul which have similar medication system and method as object hospital according to the results of questionaire. This means that many hospitals have been suffering srimilar problems which were identified in object hospital. 4. Recommendations for promoting simplification of medication system and method were the following : Redesigning of slip from two pieces of paper into one : early discharge announcement system, and slip confirming through computer and controlling of period of prescreption from one day to two or three days : designing personal drug storage box for each patient and using it. If nurses follow the recommendations, they will make medication short & simple, and also have enough time of direct nursing care 5. Even though there were many difficulties in medicating patients. Medication itself has been considered as a caring among nurses because it makes rapport between nurse and patient. So nurses had better accept medication as a portion of nusing service not a original portion of phamacist. There are some limits in this research in terms of confining to only one unit of one hospital, and treating it especially in view of nurses' aspects, So further researchs should be continnued from various kmds of viewpoints of doctors, phamacists and so on. ${\cdot\cdot\cdot}$. Especially esthnographic study of computerized medication system and method seems to be followed.

• The Korean Society of Law and Medicine
• /
• v.24 no.4
• /
• pp.103-128
• /
• 2023

According to the current act of Decision-Marking in Life-Sustaining Medicine, the decision to withhold or discontinue life-sustaining treatment is primarily based on the wishes of a patient in the dying process. Decision-making regarding life-sustaining treatment for these patients is made by the patient, if he or she is conscious, directly expressing his/her intention for life-sustaining treatment in writing or verbally or by writing an advance medical directive and physician orders for life-sustaining treatment. It can be exercised. On the other hand, if the patient has not written an advance medical directive or physician orders for life-sustaining treatment, the patient's intention can be confirmed with a statement from the patient's family, or a decision to discontinue life-sustaining treatment can be made with the consent of all members of the patient's family. However, in the case of an unrelated patient who has no family or whose family is unknown, if an advance medical directive or physician orders for life-sustaining treatment are not written before hospitalization and a medical condition prevents the patient from expressing his or her opinion, the patient's will cannot be known and the patient cannot be informed. A situation arises where a decision must be made as to whether to continue or discontinue life-sustaining treatment. This study reviewed discussions and measures for unbefriended patients under the current law in order to suggest policy measures for deciding on life-sustaining treatment in the case of unbefriended patients. First, we looked at the application of the adult guardian system, but although an adult guardian can replace consent for medical treatment that infringes on the body, permission from the family court is required in cases where death may occur as a direct result of medical treatment. It cannot be said to be an appropriate solution for patients in the process of dying. Second, in accordance with Article 14 of the Life-Sustaining Treatment Decision Act, we looked at the deliberation of medical institution ethics committees on decisions to discontinue life-sustaining treatment for patients without family ties.Under the current law, the medical institution ethics committee cannot make decisions on discontinuation of life-sustaining treatment for unbefriended patients, so through revision, matters regarding decisions on discontinuation of life-sustaining treatment for unbefriended patients are reflected in Article 14 of the same Act or separate provisions for unbefriended patients are made. It is necessary to establish and amend new provisions. In addition, the medical institution ethics committee must make a decision on unbefriended patients, but if the medical institution cannot make such a decision, there is a need to revise the law so that the public ethics committee can make decisions, such as discontinuing life-sustaining treatment for unbefriended patients.

• Journal of the Korean Chemical Society
• /
• v.66 no.5
• /
• pp.390-404
• /
• 2022

The purpose of this study was to analyze the characteristics and changes in epistemic thinking when an argument-based inquiry science class was applied in no face-to-face and face-to-face situations. Participants of this study were 113 8th grade students of four classes from a coed educational middle school in a metropolitan city. Data collection was made over one semester during which ten argument-based inquiry science lessons on five subjects were conducted in both no face-to-face and face-to-face context. As a result of comparing and analyzing students' epistemic thinking in the argumentation of each group's generating question stage, the no face-to-face classes showed higher understanding of contents and more evidence suggestion validity than face-to-face classes did. Claim validity and categories of process in argumentation were higher in face-to-face classes than No face-to-face classes. Students were able to improve their understanding of knowledge through writing by discussing rather than direct communication in no face-to-face situations, and in face-to-face situations, students showed that their thoughts were influenced by interpersonal relationships with the group members.