• Journal of Information Processing Systems
• /
• v.10 no.2
• /
• pp.223-239
• /
• 2014

New IIR digital differintegrators (differentiator and integrator) with very minor absolute relative errors are presented in this paper. The digital integrator is designed by interpolating some of the existing integrators. The optimum value of the interpolation ratio is obtained through linear programming optimization. Subsequently, by modifying the transfer function of the proposed integrator appropriately, new digital differentiator is obtained. Simulation results demonstrate that the proposed differintegrator are a more accurate approximation of ideal ones, than the existing differintegrators. Furthermore, the proposed differentiator has been tested in an image processing application. Edges characterize boundaries and are, therefore, a problem of fundamental importance in image processing. For comparison purpose Prewitt, Sobel, Roberts, Canny, Laplacian of Gaussian (LOG), Zerocross operators were used and their results are displayed. The results of edge detection by some of the existing differentiators are also provided. The simulation results have shown the superiority of the proposed approach over existing ones.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.12
• /
• pp.2046-2054
• /
• 1989

Improved algorithms are presented to design linear phase digital FIR filters with coefficients of +1,0,-1 only followed by a multiple integrator. It has been shown that the existing linear phase filter design concept for the single integrator(or, accumulator)case can be extended to the case of the multiple integrator. Linear phase conditions for the multiple integrators are summarized. Filter design methods with double or triple integrator are exploited in datail and its computer simulation results are presented to deduce the advantages of multiple integrator to the single integrator.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.1
• /
• pp.26-32
• /
• 2017

This paper presents a low power and high resolution incremental delta-sigma ADC that utilizes a passive integrator instead of an opamp-based active integrator. Opamp is a power-hungry block that involves tight design tradeoffs. To avoid the use of active integrator, the s-domain characteristic of an active integrator is first analyzed. Based on the analysis, an active integrator with low gain design is proposed as an alternative design method. To save power even more aggressively, a passive integrator with no static current is proposed. A 1st order single-bit incremental delta-sigma ADC using the proposed passive integrator is implemented in a 65nm CMOS process. Transistor-level simulation shows that the ADC consumes only 0.6uW under 1.2V supply while achieving SNDR of 71dB with 22kHz bandwidth. The estimated total power consumption including digital filter is 6.25uW, and resulting power efficiency is on a par with state-of-the-art A/D converters.

• Journal of Electrical Engineering and information Science
• /
• v.2 no.4
• /
• pp.14-18
• /
• 1997

A design methodology of the analog current-mode and width programmable integrator for a low voltage (3V) and low power application is developed and the integrator designed by this method is successfully fabricated by the 0.8$\mu\textrm{m}$ CMOS n-well single poly/double metal standard digital process. The integrator occupies the active chip area of 0.3$\textrm{mm}^2$. The experimental result illustrates a low power dissipation (1.0mW∼3.55 mW), 65dB of the dynamic range, and digitally and width programmability (10MHz∼30MHz) with an external digital 4 bit.

• Journal of Sensor Science and Technology
• /
• v.31 no.2
• /
• pp.115-119
• /
• 2022

A readout circuit for a mercury-cadmium-telluride (MCT)-amplified mid-wave infrared (IR) photodetector was realized and applied to noncontact chemical agent detectors based on a quantum cascade laser (QCL). The QCL emitted 250 times for each wavelength in 0.2-㎛ steps from 8 to 12 ㎛ with a frequency of 100 kHz and duty ratio of 10%. Because of the nonconstant QCL emission power during on-duty, averaging the photodetector signals is essential. Averaging can be performed in digital back-end processing through a high-speed analog-to-digital converter (ADC) or in analog front-end processing through an integrator circuit. In addition, it should be considered that the 250 IR data points should be completely transferred to a PC during each wavelength tuning period of the QCL. To average and minimize the IR data, we designed a readout circuit using the analog front-end processing method. The proposed readout circuit consisted of a switched-capacitor integrator, voltage level shifter, relatively low-speed analog-to-digital converter, and micro-control unit. We confirmed that the MCT photodetector signal according to the QCL source can be accurately read and transferred to the PC without omissions.

• The Journal of the Acoustical Society of Korea
• /
• v.16 no.3
• /
• pp.106-113
• /
• 1997

A 3V CMOS continuous-time fully-balanced integrator for low-voltage analog-digital mixed-mode signal processing is designed in this paper. The basic architecture of the designed fully-balanced integrator is complementary circuit which is composed of NMOS and PMOS transistor. And this complementary circuit can extend transconductance of an integrator. So. the unity gain frequency, pole and zero of integrator are increased by the extended transconductance. The SPICE simulation and small signal analysis results show that the UGF, pole and zero of the integrator is increased larger than those of the compared integrtors. The three-pole active low-pass filter is designed as a application circuit of the fully-balanced integrator, using 0.83V CMOS processing parameter.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.11
• /
• pp.1619-1626
• /
• 2021

Unlike traditional delta-sigma analog-to-digital converters, incremental analog-to-digital converters enable 1:1 mapping of input and output through a reset operation, which can be used very easily for multiplexing. Incremental analog-to-digital converters also allow for simpler digital filter designs compared to traditional delta-sigma converters. Therefore, starting with analysis in the time domain of the delayed integrator and non-delayed integrator, which are the basic blocks of analog-to-digital converter design, the design equations of a second-order input feed-forward, extended counting, 2+1 MASH (Multi-stAge-noise-SHaping), 2+2 MASH incremental analog-to-digital converter are derived in this paper. This allows not only prediction of the performance of the incremental analog-to-digital converter before design, but also the design of a digital filter suitable for each analog-to-digital converter. In addition, extended counting and MASH design techniques were proposed to improve the accuracy of analog-to-digital converters.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.7
• /
• pp.891-897
• /
• 2013

The power system frequency plays an important role in monitoring and controlling the power system. The frequency can be measured through discrete Fourier transform (DFT) coefficients of its positive fundamental frequency. The accuracy of the frequency estimate is severely affected by noise in the power system signal and the leakage effect of the negative fundamental frequency in DFT. This paper proposes a DFT-based frequency estimation algorithm to cope with the noise as well as the leakage effect. In this algorithm, two suitable digital filters are introduced to reduce efficiently frequency estimate error due to the noise. These filters are designed to use a digital bandpass filter and a second-degree integrator. The effectiveness of the proposed algorithm in reduction of frequency estimate error is verified through simulations on noise, harmonics and frequency deviation.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.5
• /
• pp.808-815
• /
• 1990

This paper treats with the design method for the single loop oversampled Sigma-Delta A/D converter with one delay and the digital integrator. Such an integrator was kgenerated by means of the bilinear transform of the analog integrator. The frequency spectrums of the quantizer and the decimator output signal are evaluated by FFT respectively. With the performance evaluation system, the values of SNR are obtained versus the input sinusoidal signal amplitude, frequency, the oversampling ratio, the DC-input level, the loop gain and the limitting value of the integrator. As compared with existing results, values of SNR versus the input signal amplitude and the oversampling ratio for the suggested system are about 6dB higher then previously reported results respectively. Furthermore, this approach achieves an about 60dB input dynamic range.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10b
• /
• pp.530-533
• /
• 1993

This paper describes a new method of dynamic error compensation, using a digital convolution integrator and two digital low pass filters. In this method, the process of compensation consists of three steps. First, sampling and digitizing of input signal, second, removing the noise in sampled data by the low pass filter and third, making a convolution integral using the output data of low pass filters. This method showed a good experimental result of reducing dynamic error even if there was a slight noise in the input signal. As a result, the detecting time constant of resistance thermo-bulb was improved to about 1/10th.