• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.2
• /
• pp.90-98
• /
• 2021

Piezoelectric ceramic fiber composite (PCFC) was fabricated using a planar electrode printed piezoelectric ceramic fiber driven in transverse mode for small-scale wind energy harvester applications. The PCFC consisted of an epoxy matrix material and piezoelectric ceramic fibers sandwiched by interdigitated electrode (IDE) patterned polyimide films. The PCFC showed an excellent mechanical performance under a continuous stress. For the fabrication of PCB cantilever harvester, five -PCFCs were vertically attached onto a flexible printed circuit board (PCB) substrate, and then PCFCs were serially connected through a printed Cu circuit. The energy harvesting performance was evaluated applying an inverted structure, which imples its free leading edge located at an open end but the trailing edge at a clamped end, to enhance strain energy in a wind tunnel. The output voltage of the PCB cantilever harvester was increased as the wind speed increased. The maximum output power was 17.2 ㎼ at a resistance load of 200 ㏀ and wind speed of 9 m/s. It is considered that the PCB cantilever energy harvester reveals a potential use for wind energy harvester applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.171-171
• /
• 2013

2층 FCCL (연성회로기판, Flexible Copper Clad Laminate)에 있어서 폴리이미드 필름과 구리의 접착력을 향상 시키기 위해 기존에 사용되고 있는 Ni-Cr대신 박리강도가 높고 에칭성도 매우 뛰어난 Ni-Mo-Nb 박막을 Roll-to roll 스퍼터 장비를 이용하여 개발하였다. 새롭게 개발된 Ni-Mo-Nb 박막은 기존 연구되어진 Ni-Cr 물질 대비 고온 박리강도 약 1.5~2.0배, 에칭성 8배 이상의 매우 우수한 특성을 보였다. Ni-Mo-Nb 접착층의 두께가 7~40 nm로 증가함에 따라 상온 박리강도가 향상 되는 것을 확인하였다. Ni-Mo-Nb 박막을 증착 하기 전 폴리이미드 기판표면을 RF 플라즈마 전처리 하였을 때 0.67 kg f/cm의 우수한 상온 박리강도를 나타내었으며 FCCL 샘플을 $150^{\circ}C$에서 168시간동안 열처리 한 후 접착력을 측정하였을 때도 0.54 kg f/cm의 높은 고온 박리강도를 보였다. FCCL의 박리강도, 표면 거칠기, 원소들의 화학적 결합, 박막의 미세구조를 peel test, atomic force microscopy, X-ray photoelectron spectroscopy, transmission electron microscopy를 이용하여 폴리이미드 기판 플라즈마 전처리 효과를 확인하였다. 그 결과 플라즈마 전처리를 한 폴리이미드 기판의 경우 처리하지 않은 기판보다 상온과 고온에서 더 우수한 접착력을 가지는 것을 확인 할 수 있었는데 이것은 폴리이미드 기판의 표면 거칠기 증가에 의한 mechanical interlocking effect가 아닌 전처리를 통한 폴리이미드 표면 개질로 C-0, C-N와 같은 chemical functional group이 증가했기 때문인 것으로 확인되었다.

• Journal of Powder Materials
• /
• v.13 no.4 s.57
• /
• pp.256-262
• /
• 2006

The amorphous $Fe_{73}Si_{16}B_7Nb_3Cu_1$ alloy strip was pulverized to get a flake-shaped powder after annealing at $425^{\circ}C$ for 90 min and subsequently ground to obtain finer flake-shaped powder by using a ball mill. The powder was mixed with polyimide-based binder of $0.5{\sim}3wt%$, and then the mixture was cold compacted to make a toroidal powder core. After crystallization treatment for 1 hour at $380{\sim}600^{\circ}C$, the powder was transformed from amorphous to nanocrystalline with the grain size of $10{\sim}15nm$. Soft magnetic characteristics of the powder core was optimized at $550{\sim}600^{\circ}C$ with the insulating binder of 3wt%. As a result, the powder core showed the outstanding magnetic properties in terms of core loss and permeability, which were originated from the optimization of the grain size and distribution of the insulating binder.

• Korean Journal of Metals and Materials
• /
• v.48 no.10
• /
• pp.951-956
• /
• 2010

This study examined the effect of copper and sulfuric acid concentrations on the surface morphology and physical properties of copper plated on a polyimide (PI) film. Electrochemical experiments with SEM and a four-point probe were performed to characterize the morphology and mechanical characteristics of copper electrodeposited in the composition of an electrolyte. The resistivity and peel strength were controlled using a range of electrolyte compositions. A lower resistivity and high flexibility were obtained when an electrolyte with 20 g/l of copper was used. However, a uniform surface was obtained when a high current density that exceeded $20mA/cm^2$ was applied, which was maintained at copper concentrations exceeding 40 g/l. Increasing sulfuric acid to >150 g/l decreased the peel strength and flexibility. The lowest resistivity and fine adhesion were detected at a $Cu^{2+}:H_2SO_4$ ratio of 50:100 g/l.

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.2
• /
• pp.63-67
• /
• 2011

We investigated effects of bonding conditions on the peel strength of rigid printed circuit board (RPCB)/ flexible printed circuit board (FPCB) joints bonded using a thermo-compression bond method, The electrodes on the FPCB were coated with Sn by a dipping process. We confirmed that the bonding temperature and bonding time strongly affected the bonding configuration and strength of the joints. Also, the peel strength is affected by dipping conditions; the optimum dipping condition was found to be temperature of $270^{\circ}C$ and time of 1s. The bonding strength linearly increased with increasing bonding temperature and time until $280^{\circ}C$ and 10s. The fracture energy calculated from the F-x (Forcedisplacement) curve during a peel test was the highest at bonding temperature of $280^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.6
• /
• pp.639-646
• /
• 2022

Energy harvesting technologies that can convert wasted various energy into usable electrical energy have been widely investigated to overcome the limitation of batteries for the powering of IoT sensors and small electronic devices. Hybrid energy harvesting is known as a technology that enhances the output power of single energy harvesting device by housing two or more various energy harvesting mechanisms. In this study, we introduce a hybrid MME (Magneto-Mechano-Electric) generator coupled with the triboelectric effect. Through FEA modeling, four triboelectric materials, including PI (Polyimide), PFA(Teflon), Cu, and Al, were selected and compared with the expected triboelectric potentials. The effect of surface morphology was investigated as well. Among various combination of triboelectric materials and surface morphologies, PFA-Al combination with the surface morphology having nano-scale square projections showed highest output potential under triboelectrification. It is also experimentally confirmed that output voltage and power of the hybrid MME generator with triboelectric material combinations.