• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.14 no.4
• /
• pp.338-347
• /
• 2021

In this paper, the beta-ray sensor circuit used in the true random number generator was designed using DB HiTek's 0.18㎛ CMOS process. The CSA circuit proposed a circuit having a function of selecting a PMOS feedback resistor and an NMOS feedback resistor, and a function of selecting a feedback capacitor of 50fF and 100fF. And for the pulse shaper circuit, a CR-RC2 pulse shaper circuit using a non-inverting amplifier was used. Since the OPAMP circuit used in this paper uses single power instead of dual power, we proposed a circuit in which the resistor of the CR circuit and one node of the capacitor of the RC circuit are connected to VCOM instead of GND. And since the output signal of the pulse shaper does not increase monotonically, even if the output signal of the comparator circuit generates multiple consecutive pulses, the monostable multivibrator circuit is used to prevent signal distortion. In addition, the CSA input terminal, VIN, and the beta-ray sensor output terminal are placed on the top and bottom of the silicon chip to reduce capacitive coupling noise between PCB traces.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.17 no.4
• /
• pp.266-274
• /
• 2024

In this paper, we designed a low-area 32-bit PF (Poly-fuse) OTP IP, a non-volatile memory that stores data required for analog circuit trimming and calibration. Since one OTP cell is constructed using two PFs in one select transistor, a 1cell-2bit multibit PF OTP cell that can program 2bits of data is proposed. The bitcell size of the proposed 1cell-2bit PF OTP cell is 1/2 of 12.69㎛ × 3.48㎛ (=44.161㎛2), reducing the cell area by 33% compared to that of the existing PF OTP cell. In addition, in this paper, a new 1 row × 32 column cell array circuit and core circuit (WL driving circuit, BL driving circuit, BL switch circuit, and DL sense amplifier circuit) are proposed to meet the operation of the proposed multbit cell. The layout size of the 32bit OTP IP using the proposed multibit cell is 238.47㎛ × 156.52㎛ (=0.0373㎛2) is reduced by about 33% compared that of the existing 32bit PF OTP IP using a single bitcell, which is 386.87㎛ × 144.87㎛ (=0.056㎛2). The 32-bit PF OTP IP, designed with 10 years of data retention time in mind, is designed with a minimum programmed PF sensing resistance of 10.5㏀ in the detection read mode and of 5.3 ㏀ in the read mode, respectively, as a result of post-layout simulation of the test chip.

• Korean Security Journal
• /
• no.13
• /
• pp.145-168
• /
• 2007

Like to change to the information-oriented society, the guard service needs to be changed. The communication and hardware technology develop rapidly and according to the internet environment change from cable to wireless, modern person can approach every kinds of information service using wireless communication machinery which can be moved such as laptop, computer, PDA, mobile phone and so on, LBS field which presents the needing information and service at anytime, anywhere, and which kinds of device expands it's territory all the more together with the appearance of ubiquitous concept. LBS use the chip in the mobile phone and make to confirm the position of the joining member anytime within several tens centimeters to hundreds meters. LBS can be divided by the service method which use mobile communication base station and apply satellite. Also each service type can be divided by location chase service, public safe service, location based information service and so on, and it is the part which will plan with guard service development. It will be prospected 8.460 hundred million in 2005 years and 16.561 hundred million in 2007 years scale of market. Like this situation, it can be guessed that the guard service has to change rapidly according to the LBS application. Study method chooses documentary review basically, and at first theory method mainly uses the second documentary examination which depends on learned journal and independent volume which published in the inside and the outside of the country, internet searching, other kinds of all study report, statute book, thesis which published at public order research institute of the Regional Police Headquarter, police operation data, data which related with statute, documents and statistical data which depend on private guard company and so on. So the purpose of the study gropes in accordance with the LBS application, and present the problems and improvement method to analyze indirect of manager side of operate guard adaptation service of LBS, government side which has to activate LBS, systematical, operation management, manpower management and education training which related with guard course side which has to study and educate in accordance with application of the new guard service, as well as intents to excellent quality service of guard.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.7
• /
• pp.122-130
• /
• 2013

This work proposes a 12b 100MS/s 45nm CMOS four-step pipeline ADC for high-speed digital communication systems requiring high resolution, low power, and small size. The input SHA employs a gate-bootstrapping circuit to sample wide-band input signals with an accuracy of 12 bits or more. The input SHA and MDACs adopt two-stage op-amps with a gain-boosting technique to achieve the required DC gain and high signal swing range. In addition, cascode and Miller frequency-compensation techniques are selectively used for wide bandwidth and stable signal settling. The cascode current mirror minimizes current mismatch by channel length modulation and supply variation. The finger width of current mirrors and amplifiers is laid out in the same size to reduce device mismatch. The proposed supply- and temperature-insensitive current and voltage references are implemented on chip with optional off-chip reference voltages for various system applications. The prototype ADC in a 45nm CMOS demonstrates the measured DNL and INL within 0.88LSB and 1.46LSB, respectively. The ADC shows a maximum SNDR of 61.0dB and a maximum SFDR of 74.9dB at 100MS/s, respectively. The ADC with an active die area of $0.43mm^2$ consumes 29.8mW at 100MS/s and a 1.1V supply.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.7
• /
• pp.1218-1226
• /
• 2008

With the development of semiconductor integrated technology and with the increasing use of multimedia functions in computer, more functions have been implemented as hardware. Nowadays, most microprocessors beyond 32 bits generally implement an integer multiplier as hardware. However, as for a divider, only specific microprocessor implements traditional SRT algorithm as hardware due to complexity of implementation and slow speed. This paper suggested an algorithm that uses a multiplier, 'w bit $\times$ w bit = 2w bit', to process $\frac{N}{D}$ integer division. That is, the reciprocal number D is first calculated, and then multiply dividend N to process integer division. In this paper, when the divisor D is '$D=0.d{\times}2^L$, 0.5 < 0.d < 1.0', approximate value of ' $\frac{1}{D}$', '$1.g{\times}2^{-L}$', which satisfies ' $0.d{\times}1.g=1+e$, $e<2^{-w}$', is defined as over reciprocal number and then an algorithm for over reciprocal number is suggested. This algorithm multiplies over reciprocal number '$01.g{\times}2^{-L}$' by dividend N to process $\frac{N}{D}$ integer division. The algorithm suggested in this paper doesn't require additional revision, because it can calculate correct reciprocal number. In addition, this algorithm uses only multiplier, so additional hardware for division is not required to implement microprocessor. Also, it shows faster speed than the conventional SRT algorithm and performs operation by word unit, accordingly it is more suitable to make compiler than the existing division algorithm. In conclusion, results from this study could be used widely for implementation SOC(System on Chip) and etc. which has been restricted to microprocessor and size of the hardware.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.11
• /
• pp.51-62
• /
• 2003

This paper presents a novel survivor memeory management and decoding techniques with sequential backward state transition control in the trace back Viterbi decoder. The Viterbi algorithm is an maximum likelihood decoding scheme to estimate the likelihood of encoder state for channel error detection and correction. This scheme is applied to a broad range of digital communication such as intersymbol interference removing and channel equalization. In order to achieve the area-efficiency VLSI chip design with high throughput in the Viterbi decoder in which recursive operation is implied, more research is required to obtain a simple systematic parallel ACS architecture and surviver memory management. As a method of solution to the problem, this paper addresses a progressive decoding algorithm with sequential backward state transition control in the trace back Viterbi decoder. Compared to the conventional trace back decoding techniques, the required total memory can be greatly reduced in the proposed method. Furthermore, the proposed method can be implemented with a simple pipelined structure with systolic array type architecture. The implementation of the peripheral logic circuit for the control of memory access is not required, and memory access bandwidth can be reduced Therefore, the proposed method has characteristics of high area-efficiency and low power consumption with high throughput. Finally, the examples of decoding results for the received data with channel noise and application result are provided to evaluate the efficiency of the proposed method.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.12 s.354
• /
• pp.15-22
• /
• 2006

In this paper, 1.8V 8-bit 500MSPS Low-power CMOS Digital-to-Analog Converter(DAC) for UWB(Ultra Wide Band) Communication Systeme is proposed. The architecture of the DAC is based on a current steering 6+2 full matrix type which has low glitch and high linearity. In order to achieve a high speed and good performance, a current cell with a high output impedance and wide swing output range is designed. Further a thermometer decoder with same delay time and low-power switching decoder for high efficiency performance are proposed. The proposed DAC was implemented with TSMC 0.18um 1-poly 6-metal N-well CMOS technology. The measured SFDR was 49dB when the output frequency was 50MHz at 500MS/s sampling frequency. The measured INL and DNL were 0.9LSB and 0.3LSB respectively. The DAC power dissipation was 20mW and the effective chip area was $0.63mm^2$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.6
• /
• pp.1154-1162
• /
• 2016

This paper proposes a fast-transient digital LDO(Low dropout) regulator with binary-weighted current control technique. Conventional digital LDO takes a long time to stabilize the output voltage, because it controls the amount of current step by step, thus ringing problem is generated. Binary-weighted current control technique rapidly stabilizes output voltage by removing the ringing problem. When output voltage reliably reaches the target voltage, It added the FRZ mode(Freeze) to stop the operation of digital LDO. The proposed fast response digital LDO is used with a slow response DC-DC converter in the system which rapidly changes output voltage. The proposed digital controller circuit area was reduced by 56% compared to conventional bidirectional shift register, and the ripple voltage was reduced by 87%. A chip was implemented with a $0.18{\mu}F$ CMOS process. The settling time is $3.1{\mu}F$ and the voltage ripple is 6.2mV when $1{\mu}F$ output capacitor is used.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.7
• /
• pp.739-747
• /
• 2007

Dual-mode bandpass filter was designed by using periodic stepped impedance ring resonator with step perturbation. The periodic stepped impedance ring resonator has the effects of size reduction and $2^{nd}$ harmonic suppression by changing characteristic impedance ratio. The perturbation for dual-mode generation was also easily controlled by characteristic impedance ratio, and the variation of dual-mode resonant frequencies and attenuation pole frequencies were analyzed by the effect of step perturbation. Chip capacitors were used for input/output coupling, and the variation of center frequency by the coupling capacitance and step perturbation was also considered. From the results, two types of 2 GHz dual-mode bandpass filter were fabricated in size of $14{\times}14mm^2$, those have different attenuation poles and bandwidths. The measured results of proposed bandpass filters showed a good agreement with the calculated estimations, and those have insertion loss of 2.52, 0.52 dB and 3 dB bandwidth of 4.03, 15.02 %, respectively.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.443-446
• /
• 2003

This paper implement Remote Meter Reading System which is used Bluetooth and SMS in CDMA. This System propose system which tan detect a total amount of gas, electricity or water without a meterman, at home BlueTooth is a close range wireless communication technology which uses a wireless frequency 2.4GHz and has a high trust and self error correction technology according to a low power consumption quality and a high-speed frequency hopping. This makes get a high trust concerning a data transmission than an existing modem. In addition, though wireless modem is restricted by a minimal of a wireless terminal, it will be possible to coincide with the function of the portable with the low power consumption quality by using Bluetooth. And as the system on a chip of module progresses, the possibility of the small size is present. Nowadays, SMS Protocol in CDMA for have a network function based on PPP in CDMA Phone. The proposed Remote Meter Reading System to get more nobility, efficiency, and have good function. SMS Protocol in CDMA have profits which is low power, low cost, and low microwave output.