• 한국재료학회지
• /
• 제13권11호
• /
• pp.711-716
• /
• 2003

Gate length, height, and silicide thickness have all been shrinking linearly as device density has progressively increased over the years. We investigated the effect of the cobalt diffusion during the silicide formation process on the 60$\AA$-thick gate oxide lying underneath the Ti/Co and Co/Ti bilayers. We prepared four different cobalt silicides, which have similar sheet resistance, made from the film structure of Co/Ti(interlayer), and Ti(capping layer)/Co, and peformed the current-voltage, time-to-break down, and capacitance-voltage measurements. Our result revealed that the cobalt silicide process without the Ti capping layer allowed cobalt atoms to diffuse into the upper interface of gate oxides. We propose that 100$\AA$-thick titanium interlayer may lessen the diffusion of cobalt to gate oxides in 1500-$\AA$ height polysilicon gates.

• 대한전자공학회논문지SD
• /
• 제40권12호
• /
• pp.1-9
• /
• 2003

본 논문에서는 cobalt interlayer와 TiN capping을 적용한 Ni-Silicide 구조를 제안하여 100 ㎜ CMOS 소자에 적용하고 소자 특성 연구를 하였다. Ni-Silicide의 취약한 열 안정성을 개선하기 위해 열 안정성이 우수한 Cobalt interlayer이용하여 silicide의 열화됨을 개선하였고 또한 silicide 계면의 uniformity를 향상하기 위해 TiN capping을 동시에 적용하였다. 100 ㎚ CMOS 소자에 제안한 Co/Ni/TiN 구조를 적용하여 700℃, 30분에서의 열처리 시에도 silicide의 낮은 면저항과 낮은 접합 누설 전류가 유지되었으며 100 ㎚이하 소자의 특성 변화도 거의 없음을 확인하였다. 따라서 제안한 Co/Ni/TiN 구조가 NiSi의 열 안정성을 개선시킴으로써 100 ㎚ 이하의 Nano CNOS 소자에 매우 적합한 Ni-Silicide 특성을 확보하였다.

• 대한금속재료학회지
• /
• 제46권2호
• /
• pp.88-96
• /
• 2008

Thermal evaporated 10 nm-$Ni_{50}Co_{50}$/(70 nm-poly)Si films were deposited to examine the energy saving properties of silicides formed by rapid thermal annealing at temperature ranging from 500 to $1,100^{\circ}C$ for 40 seconds. Thermal evaporated 10 nm-Ni/(70 nm-poly)Si films were also deposited as a reference using the same method for depositing the 10 nm-$Ni_{50}Co_{50}$/(70 nm-poly)Si films. A four-point probe was used to examine the sheet resistance. Transmission electron microscopy (TEM) and X-ray diffraction XRD were used to determine cross sectional microstructure and phase changes, respectively. UV-VIS-NIR and FT-IR (Fourier transform infrared spectroscopy) were used to examine the near-infrared (NIR) and middle-infrared (MIR) absorbance. TEM analysis confirmed that the uniform nickel-cobalt composite silicide layers approximately 21 to 55 nm in thickness had formed on the single and polycrystalline silicon substrates as well as on the 25 to 100 nm thick nickel silicide layers. In particular, nickel-cobalt composite silicides showed a low sheet resistance, even after rapid annealing at $1,100^{\circ}C$. Nickel-cobalt composite silicide and nickel silicide films on the single silicon substrates showed similar absorbance in the near-IR region, while those on the polycrystalline silicon substrates showed excellent absorbance until the 1,750 nm region. Silicides on polycrystalline substrates showed high absorbance in the middle IR region. Nickel-cobalt composite silicides on the poly-Si substrates annealed at $1,000^{\circ}C$ superior IR absorption on both NIR and MIR region. These results suggest that the newly proposed $Ni_{50}Co_{50}$ composite silicides may be suitable for applications of IR absorption coatings.

• 한국세라믹학회지
• /
• 제38권10호
• /
• pp.871-875
• /
• 2001

Cobalt silicidation at sidewall spacer edge of Metal-Oxide-Semiconductor Field-Effect Transistors (MOSFETs) with post annealing treatment for capacitor forming process has been investigated as a function of dopant species. Cobalt silicidation of nMOSFET with n-type Lightly Doped Drain (LDD) and pMOSFET with p-type LDD produces a well-developed cobalt silicide with its lateral growth underneath the sidewall spacer. In case of pMOSFET with n-type LDD, however, a void is formed at the sidewall spacer edge with no lateral growth of cobalt silicide. The void formation seems to be due to a retarded silicidation process at the LDD region during the first Rapid Thermal Annealing (RTA) for the reaction of Co with Si, resulting in cobalt mono silicide at the LDD region. The subsequent second RTA converts the cobalt monosilicide into cobalt disilicide with the consumption of Si atoms from the Si substrate, producing the void at the sidewall spacer edge in the Si region. The void formed at the sidewall spacer edge serves as a resistance in the current-voltage characteristics of the pMOSFET device.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 전기.전자공학 학술대회 논문집
• /
• pp.387-390
• /
• 1988

The increases in the packing density and the resulting shrinkage of silicon integrated circuit dimensions led to the investigation and successful of the deposited silicide layers as the gate and interconnection and contact metallization. In this paper evaporated Co films on n-Si have been rapid thermal annealed in $N_2$ambient at temperature of $400^{\circ}C-1000^{\circ}C$. The Co silicide formation is characterized by sheet resistance (4PP). Also, silicide growth rate and its reproductivity has been examined by SEM.

• Journal of Information Display
• /
• 제1권1호
• /
• pp.63-69
• /
• 2000

In order to improve both the level and the stability of electron emission, Mo and Co silicides were formed from Mo mono-layer and Ti/Co bi-layers on single crystal silicon field emitter arrays (FEAs), respectively. Using the slope of Fowler-Nordheim curve and tip radius measured from scanning electron microscopy (SEM), the effective work function of Mo and Co silicide FEAs were calculated to be 3.13 eV and 2.56 eV, respectively. Compared with silicon field emitters, Mo and Co silicide exhibited 10 and 34 times higher maximum emission current, 10 V and 46 V higher device failure voltage, and 6.1 and 4.8 times lower current fluctuation, respectively. Moreover, the emission currents of the silicide FEAs depending on vacuum level were almost the same in the range of $10^{-9}{\sim}10^{-6}$ torr. This result shows that silicide is robust in terms of anode current degradation due to the absorption of air molecules.

• 한국재료학회지
• /
• 제16권10호
• /
• pp.656-662
• /
• 2006

We fabricated thermal evaporated 10 nm-$Ni_xCo_{1-x}$ (x=0.2, 0.5 and 0.8) /(poly)Si films to form nanothick cobalt nickel composite silicides by a rapid thermal annealing at $700{\sim}1100^{\circ}C$ for 40 seconds. A field emission scanning electron microscope and a micro-Raman spectrometer were employed for microstructure and silicon residual stress characterization, respectively. We observed self-aligned micro-pinholes on single crystal silicon substrates silicidized at $1100^{\circ}C$. Raman silicon peak shift indicates that the residual tensile strain of $10^{-3}$ in single crystal silicon substrates existed after the silicide process. We propose thermal stress from silicide exothermic reaction and high temperature silicidation annealing may cause the pinholes. Those pinholes are expected to be avoided by lowering the silicidation temperature. Our results imply that we may use our newly proposed composite silicides to induce the appropriate strained layer in silicion substrates.

• 한국세라믹학회지
• /
• 제38권9호
• /
• pp.782-786
• /
• 2001

Cobalt silicide has been employed to Embedded DRAM (Dynamic Random Access Memory) and Logic (EDL) as contact material to improve its speed. We have investigated the influences of Ti and TiN capping layers on cobalt-silicided Complementary Metal-Oxide-Semiconductor (CMOS) device characteristics. TiN capping layer is shown to be superior to Ti capping layer with respect to high thermal stability and the current driving capability of pMOSFETs. Secondary Ion Mass Spectrometry (SIMS) showed that the Ti capping layer could not prevent the out-diffusion of boron dopants. The resulting operating current of MOS devices with Ti capping layer was degraded by more than 10%, compared with those with TiN.

• 한국재료학회지
• /
• 제17권2호
• /
• pp.73-80
• /
• 2007

For the sub-65 nm CMOS process, it is necessary to develop a new silicide material and an accompanying process that allows the silicide to maintain a low sheet resistance and to have an enhanced thermal stability, thus providing for a wider process window. In this study, we have evaluated the property and unit process compatibility of newly proposed composite silicides. We fabricated composite silicide layers on single crystal silicon from $10nm-Ni_{1-x}Co_x/single-crystalline-Si(100),\;10nm-Ni_{1-x}Co_x/poly-crystalline-\;Si(100)$ wafers (x=0.2, 0.5, and 0.8) with the purpose of mimicking the silicides on source and drain actives and gates. Both the film structures were prepared by thermal evaporation and silicidized by rapid thermal annealing (RTA) from $700^{\circ}C\;to\;1100^{\circ}C$ for 40 seconds. The sheet resistance, cross-sectional microstructure, surface composition, were investigated using a four-point probe, a field emission scanning probe microscope, a field ion beam, an X-ray diffractometer, and an Auger electron depth profi1ing spectroscopy, respectively. Finally, our newly proposed composite silicides had a stable resistance up to $1100^{\circ}C$ and maintained it below $20{\Omega}/Sg$., while the conventional NiSi was limited to $700^{\circ}C$. All our results imply that the composite silicide made from NiCo alloy films may be a possible candidate for 65 nm-CMOS devices.

• 한국산학기술학회논문지
• /
• 제6권3호
• /
• pp.270-272
• /
• 2005

코발트 실리사이드는 낮은 전기 저항성 때문에 고효율 소자를 제조하는데 적합한 물질이다. 이는 전자소재가 소형화되면서 접촉저항과 혼합을 줄이기 위해 더욱 필요하게 되었다. 본 연구에서는 티타늄의 표면산화에 미치는 영향과, RTO 조건에서 온도에 따른 코발트 실리사이드 박막의 산화정도를 측정했다. 기질로서 p-형 실리콘웨이퍼를 사용하였고, 고속 열 가공을 통하여 박막을 가공하였다. 티타늄 층을 입혔을 때 산화충의 두께는 $500{\AA}$정도 성장하였다. 고속 열산화의 온도변화에 따라 산화막은 $550^{\circ}C\~700^{\circ}C$까지는 성장을 보였으나 $700^{\circ}C$이상에는 산화막 성장이 포화상태를 보였다.