• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.05a
• /
• pp.467-472
• /
• 2005

In this paper, design and control of the novel SEPIC-Flyback converter(SF converter) is developed as a possible converter for fuel cell system. This output characteristic of SF converter is similar to Buck-Boost converter in that it can step-up or step-down the voltage. With the small signal equivalent circuit modeling of SF converter, control-to-output transfer function is obtained. SF converter couples up the inductive type converter to capacitive type converter with one transformer, which has less ripple current than its respective one does. To verify the validity of the proposed converter, 500W, 100kHz converter is designed and tested. ZVS switching and active clamping are also tested in practice.

• Journal of Power Electronics
• /
• v.9 no.6
• /
• pp.929-939
• /
• 2009

This paper presents a new soft-switching boost converter based on the LC resonance and passive clamping technique without additional active switches. The circuit achieves high efficiency and low voltage stress by adopting a soft switching method using LC resonance. This paper gives a mathematical analysis of each mode and a detailed design procedure of the proposed boost converter. First of all, the operational principles are verified through simulation results. Then, according to the design procedure, we designed and built a 1.5[kW] prototype soft switching boost converter. Through the experimental results, we demonstrated the validity and usefulness of the proposed boost converter.

• Journal of Industrial Technology
• /
• v.19
• /
• pp.1-7
• /
• 1999

This is the pre-study to pile up the basic technique for the electro-discharge machining in the field of micro-drilling. The machined chips are flowed out from the machining area by the flow arisen from the high speed rotation of the electrode. The cylindrical shape electrode, whose diameter is 0.5mm, is clamped by the three point clamping type clamper and the clamper is attached at the front shaft of the high speed rotating DC motor. The current for machining is controlled by pulse width modulation technique and the machining conditions such as frequency and duty ratio are changed to find out the effect of the variables for machined results.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.1161-1165
• /
• 2005

Due to the miniaturization of electrical components and assembles on signal circuits, transient overvoltages caused by switching operation or lightning surges have become more interesting concern to the field of electrical engineering. In this paper, the development of surge protective devices(SPDs) that can protect sensitive signal device on shipboard from overvoltages are described. Two kinds of SPDs are designed and tested by using a combination surge generator which can produce the standard impulse current of 8/20${\mu}s$ 2.1kA according to the IEC 61000-4-5 standard. From the simulation and experimental results, it is confirmed that the proposed SPDs have an enough protection performance with a low insertion loss and a low clamping voltage.

• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.142-143
• /
• 2010

An active-clamped current-fed half-bridge converter for the high step-up application is proposed in this paper. The proposed converter is composed of active clamping snubber circuits and a voltage doubler rectifier. The operational principle, theoretical analysis, and design considerations are presented. To confirm the operation, features, and validity of the proposed circuit, the experimental result for a 200W, 24V input and 400V output prototype are presented.

• Proceedings of the KIEE Conference
• /
• 1999.11b
• /
• pp.406-408
• /
• 1999

In order to reduce the overall size and cost, researchers attempted to integrate the functions of power factor correction(PFC) and isolated dc-dc conversion into single power stage. However, single-stage isolated PFC converters have higher voltage stress and heavier loss when compared with a normal dc-dc converters. In this paper, we propose to add active clamping circuit to keep the switch voltage stress low and to achieve soft switching of electronic devices.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.2169-2171
• /
• 1998

In order to improved the three phase GTO CSI of high efficiency IM drive with low loss commutation and snubber energy, we studied the energy recovery circuit to recover stored energy in clamping capacitor, dc link inductor and snubber capacitor, used an induction motor as the load of inverter. Specially, we investigated how dc input power is increased or decreased according to size of dc link inductor. The validity of this system is proved through experiment.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.9
• /
• pp.450-453
• /
• 2005

A high speed address recovery technique for AC plasma display panel(PDP) is proposed. Replacing GND switch by clamping diode. the recovery speed can be increased by saving GND hold-time and switching loss due to GND switch also becomes also be reduced. The proposed method is able to perform load-adaptive operation by controlling the voltage level of energy recovery capacitor, which prevents increasing inefficient power consumption caused by circuit loss during recovery operation. Test results with 50' HD single-scan PDP(resolution = 1366$\times$768) show that less than 3sons of recovery time is successfully accomplished and about$54\%$ of the maximum power consumption can be reduced, tracing minimum power consumption curves.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.12 no.1
• /
• pp.117-125
• /
• 1998

In this paper, in order to develop the three phase GTO CSI of high efficiency 1M drive with low loss commutation and snubber energy, we studied the energy recovery circuit to recover stored energy in clamping capacitor and DC link inductor(VCC-l and VCC-2), and snubber capacitor(VCC-3). By using an induction motor as the load of inverter, experimental results show that dissipated DC power is decreased and capacitor voltage Vc is effectively suppressed by VCC-2 and VCC-3 system, and the validity of VCC-3 system with low loss commutation and snubber energy is proofed.roofed.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.3
• /
• pp.257-265
• /
• 2014

This paper proposes a simple compensation method for switches of the unclamped voltage in the three-level NPC inverter. Voltages of inner-switches can be unclamped in the three-level NPC (neutral point clamped) inverter. It can cause the problem of the switch fault accident. By adding a capacitor, switches of the unclamped voltage can be clamped. Through the analysis of the circuit, the reason behind switches being unclamped was verified which leads to the solution method that designs a compensation capacitor. The proposed method was validated through the simulation and experimental results.