• Journal of Korea Society of Industrial Information Systems
• /
• v.20 no.1
• /
• pp.49-55
• /
• 2015

This paper proposes a 2.4 GHz RF oscillator with a very low close-in phase noise performance. This is composed of a low frequency crystal oscillator and three frequency multipliers such as two doubler (X2) and one tripler (X3). The proposed oscillator is implemented as a hybrid type circuit design using a discrete silicon bipolar transistor. The measurement results of the proposed oscillator structure show -115 dBc/Hz close-in phase noise at 10 kHz offset frequency, while only dissipating 5 mW from a 1-V supply. Its close-in phase noise level is very close to that of a low frequency crystal oscillator with little degradation of noise performance. The proposed structure which is consisted of a low frequency crystal oscillator and a frequency multiplier provides new method to implement a low power low close-in phase noise RF local oscillator.

• Proceedings of the IEEK Conference
• /
• 2000.07b
• /
• pp.559-562
• /
• 2000

The problem of noise generation due to PWM switched-mode power converter has been widely noticed from the viewpoint of Electromagnetic Interference(EMI). Many kings of topologies for resonant converters have been developed both to overcome this noise problem and to attain high power efficiency. It is reported in references that resonant converters which are derived from PWM converter using resonant switch show much lower noise characteristics than PWM converter, and that current-mode resonant converter is more sensitive to stored charge in rectifying diode than voltage-mode counterpart concerning surge generation at diode’s turn-off. On the other hand, above mentioned resonant converters have defect of high-voltage stress on semiconductor switch and complicated circuit configuration. Hence, the simplified Forward-type resonant converter has been proposed and investigated due to its prominent features of simplicity of circuit configuration, low voltage stress and high stability. However, its noise characteristics still remain unknown. The purpose of this paper is to study quantitatively the noise characteristics of this simplified Forward-type resonant converter by experiment and analysis. The influence of parasitic elements and stored charge in rectifying diode on noise generation has been clarified.

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.628-633
• /
• 2003

Recently, the electronic circuit with microprocessor based control system instead of conventional analog circuit is widely used for rolling stock, and also these circuits are widely adopted for train control and monitoring in modem rapid transit system. Noise, distortion and attenuation are always present in electronic equipments and strictly limit performance. The purpose of this paper is to propose noise reduction technology for electronic equipments in rolling stock.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.4
• /
• pp.397-404
• /
• 2010

The use of equivalent circuit models of piezoelectric energy harvesters is inevitable when power circuitry including rectifying and smoothing circuit elements is connected to them for evaluating DC electrical outputs. This is because it is difficult to incorporate the electro-mechanical coupling resulting from the additional circuitry into the conventional finite element analysis. Motivated by this observation, we propose a method to accurately extract the equivalent circuit parameters by using commercially available FEM software such as ANSYS which provides three-dimensional AC piezoelectric analysis. Then the equivalent circuit can be analyzed by circuit simulators such as $SimPowerSystems^{TM}$ of MATLAB. While the previous works have estimated the circuit parameters by experimental measurements or by analytical solutions developed only for limited geometries and boundary conditions, the proposed method has no such limitation because piezoelectric energy harvesters of any shapes and boundary conditions can be treated in FEM software. For the verification of the proposed method, multi-modal AC electrical power output by using a corresponding equivalent circuit is compared with that by ANSYS. The proposed method is then shown to be very useful in the subsequent evaluation of DC electrical output which is obtained by attaching a bridge diode and a storage capacitor to a piezoelectric energy harvester.

• Journal of IKEEE
• /
• v.13 no.4
• /
• pp.9-14
• /
• 2009

This paper describes measurement of an on-ship power supply noise in mixed-signal integrated circuits. To measure the on-chip power supply noise, we can check the effects of analog circuits and compensate it. This circuit consists of two independent measurement channels, each consisting of a sample and hold circuit and a frequency to digital converter which has a buffer and voltage controlled oscillator(VCO). The time-based voltage information and frequency-based power spectrum density(PSD) can be achieved by a simple analog to digital conversion scheme. The buffer works like a unit-gain buffer with a wide bandwidth and VCO has a high gain to improve resolution. This circuit was fabricated in a 0.18um CMOS technology and has 2.06mV/count. The noise measurement circuit consumes 15mW and occupies $0.768mm^2$.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.10a
• /
• pp.190-195
• /
• 2000

This paper presents the fabrication of the LNA which is operating at 2.13∼2.16 GHz for IMT-2000 lot-end receiver using series feedback and resistive decoupling circuit. Series feedback added to the source lead of a transistor keep the low noise characteristics and drop the input reflection coefficient of amplifier simultaneously. Also, it increases the stability of the LNA. Resistive decoupling circuit is suitable for input stage matching because a signal at low frequency is dissipated by a resistor in the matching network The amplifier consist of GaAs FET ATF-10136 for low noise stage and VNA-25 which is internally matched MMIC for high gain stage. The amplifier is fabricated with both the RF circuits and self bias circuit on the Teflon substrate with 3.5 permittivity. The measured results of the LNA which is fabricated using above design technique are presented more than 30 dB in gain P$\_$ldB/ 17 dB and less than 0.7 dB in noise figure, 1.5 in input$.$output SWR(Standing Wave Ratio).

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.10 no.4
• /
• pp.300-308
• /
• 2010

This paper describes the development of a low-power electrocardiogram (ECG) touch sensor intended for the use with two dry metal electrodes. An equivalent ECG extraction circuit model encountered in a ground-free two-electrode configuration is investigated for an optimal sensor read-out circuit design criteria. From the equivalent circuit model, (1) maximum sensor resolution is derived based on the electrode's background thermal noise, which originates from high electrode-skin contact impedance, together with the input referred noise of instrumentation amplifier (IA), (2) 60 Hz electrostatic coupling from mains and motion artifact are also considered to determine minimum requirement of common mode rejection ratio (CMRR) and input impedance of IA. A dedicated ECG read-out front end incorporating chopping scheme is introduced to provide an input referred circuit noise of 1.3 ${\mu}V_{rms}$ over 0.5 Hz ~ 200 Hz, CMRR of IA > 100 dB, sensor resolution of 7 bits, and dissipating only 36 ${\mu}W$. Together with 8 bits synchronous successive approximation register (SAR) ADC, the sensor IC chip is implemented in 0.18 ${\mu}m$ CMOS technology and integrated on a 5 cm $\times$ 8 cm PCB with two copper patterned electrodes. With the help of proposed touch sensor, ECG signal containing QRS complex and P, T waves are successfully extracted by simply touching the electrodes with two thumbs.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.9 no.4
• /
• pp.141-146
• /
• 2010

In this paper, bandgap reference PTAT(Proportional to Absolute Temperature) circuit and flexible gain control of LNA(Low Noise Amplifier) which is usable in Zigbee system of 2.4GHz band are designed by TSMC $0.18{\mu}m$ CMOS library. PTAT bandgap reference circuit is proposed to minimize the instability of CMOS circuit which may be unstable in temperature changes. This circuit is designed such that output voltage remains within 1.3V even when the temperature varies from $-40^{\circ}C$ to $-50^{\circ}C$ when applied to the gate bias voltage of LNA. In addition, the LNA is designed to be operated on 2.4GHz which is applicable to Zigbee system and able to select gains by changing output impedance using 4 NMOS operated switches. The simulation result shows that achieved gain is 14.3~17.6dB and NF (Noise Figure) 1.008~1.032dB.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.3
• /
• pp.198-206
• /
• 2011

This paper presents a new programmable compensation circuit (PCC) for a System-on-Chip (SoC). The PCC is integrated with $0.18-{\mu}m$ BiCMOS SiGe technology. It consists of RF Design-for-Testability (DFT) circuit, Resistor Array Bank (RAB) and digital signal processor (DSP). To verify performance of the PCC we built a 5-GHz low noise amplifier (LNA) with an on-chip RAB using the same technology. Proposed circuit helps it to provide DC output voltages, hence, making the RF system chain automatic. It automatically adjusts performance of an LNA with the processor in the SoC when it goes out of the normal range of operation. The PCC also compensates abnormal operation due to the unusual PVT (Process, Voltage and Thermal) variations in RF circuits.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.3
• /
• pp.180-185
• /
• 2003

The equivalent electroacoustic circuit approach has been conventionally used for the analysis of the multiple layer perforated plate system. However, it is found that an analogy error has been involved in the equivalent electroacoustic approach proposed by previous researchers for the element of straight pipe. Although the pipe between the perforated layers is a distributed element in the analogy, it has been treated as a parallel element by previous investigators. The analogy error is demonstrated by comparing the calculated absorption coefficients based on the parallel circuit and the distributed circuit, respectively, with the measured values by the two-microphone impedance tube method.