• 한국전기전자재료학회논문지
• /
• 제13권7호
• /
• pp.592-597
• /
• 2000

In this study (B $a_{0.5}$/S $r_{0.5}$)Ti $O_3$[BST(50/50)] ceramic thin films were prepared by the Sol-Gel method BST(50/50) stock solution was made and spin-coated on the Indium Tin Oxide(ITO)/glass substrate at 4000 rpm for 30 seconds. The coated films were dried at 35$0^{\circ}C$ for 10 minutes and annealed at 650~75$0^{\circ}C$ for 1 hour. The microstructural properties of the BST(50/50) thin film were studied by the XRD and AFM. The ferroelectric perovskite phase was formed at the annealing condition of 75$0^{\circ}C$ for 1 hour. Dielectric constant and loss of this thin were 370, 3.7% at room temperature respectively. The polarization switching voltage showed the good value of 3V. The leakage current density of the BST(50/50) thin film was 10$^{-7A}$c $m^2$with applied voltage of 1.5V. BST(50/50) thin film capacitors having good dielectric and electrical properties are expecting for the application to the dielectric material of DRAM.RAM.M.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.473-476
• /
• 1997

Focused Ar ion laser beam can be utilized to fabricate microstructures on silicon substrate as well as other materials(e.g. such as ceramic). The laser using in this study is an argon ion laser with maximum power of 6 W, wavelength of 514 nm. This laser beam is focused by objectives with a high numerical aperture, a long working distance. We have achieved line width about 1 ${\mu}{\textrm}{m}$ with high scan speed. The resolution for Si machining is determined by the selectivity of the chemical reaction rather than the laser spot size. In this study, we have obtained the maximum etch rate of 434.7 ${\mu}{\textrm}{m}$/sec with high aspect ratio. The characteristics of etched groove was investigated by scanning electron microscope(SEM) and auger electron spectroscopy(AES). It is assumed that the technique using arson ion laser is applicab1e to fabricate microstructures.

• 한국전기전자재료학회논문지
• /
• 제16권5호
• /
• pp.361-364
• /
• 2003

It was investigated that the structural and electrical Properties of Ce-doped Ba(Zr$_{x}$Ti$_{1-x}$ )O$_3$ (BCZT) thin films with a mole fraction of x=0.2 and a thickness about 100 nm. BCZT films were prepared on Pt/Ti/SiO$_2$/Si substrate by a RF magnetron sputtering system. We have measured the thickness profile with Ar/O$_2$ ratio and the surface roughness. It was observed that the oxygen gas, which introduced during the film deposition, have an influence on the roughness of the film and the film roughness was reduced by annealing from 2.33 nm to 2.02 nm (RMS at 500 $^{\circ}C$, Ar:6 sccm, $O_2$:6 sccm). It was found that annealing procedure after top electrode deposit can reduce the dissipation factor.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.262-263
• /
• 2007

Effect of co-doping on optical and electrical properties of $SnO_2$ based thin films were studied. $SnO_2$ ceramic targets with up to 50mol% $CuSb_2O_6$ were prepared by sintering mixed-oxide compact in the temperature range of $1100^{\circ}C{\sim}1300^{\circ}C$ in air. Thin films were then deposited onto glass substrates by pulsed laser deposition where substrate temperature was maintained in the range of $500{\sim}650^{\circ}C$ with oxygen pressure of 3m~7.5mTorr and energy density of $1Jcm^{-2}$. It was found that with the increase amount of dopant, the electrical properties of thin films tended to improve with the smallest resistivity value obtained at about 8mol% doping, further increase, however, usually impaired the optical transmission in the visible range.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.366-367
• /
• 2006

Different orientated SBN thin films were deposited by Ion Beam Sputtering, and electric properties were measured on each orientation. Ferroelectric $Sr_xBa_{1-x}Nb_2O_6$(SBN) has excellent electro-optic, photo-refractive, piezoelectric, pyroelectric properties. SBN thin film has been deposited by various method, of sol-gel, PLD, CVD, sputtering, etc.. To avoid lead pollution of Pb-system perovskite ferroelectric materials. SBN thin films were fabricated for pyroelectric IR sensor. Using the ceramic target of the same composition and Pt(100)/$TiO_2/SiO-2$/Si(100) substrate, crystallization and orientation behavior as well as electric properties of the films were examined. Seed layer and thin films thickness was controlled to observe the effect on preferred orientation. We measured I-V, C-V, P-E hysteresis to characterize electric-properties on each orientations.

• 마이크로전자및패키징학회지
• /
• 제26권3호
• /
• pp.15-22
• /
• 2019

In these days, importance of the power electronic devices and modules keeps increasing due to electric vehicles and energy saving requirements. However, current silicon-based power devices showed several limitations. Therefore, wide band gap (WBG) semiconductors such as SiC, GaN, and $Ga_2O_3$ have been developed to replace the silicon power devices. WBG devices show superior performances in terms of device operation in harsh environments such as higher temperatures, voltages and switching speed than silicon-based technology. In power devices, the reliability of the devices and module package is the critically important to guarantee the normal operation and lifetime of the devices. In this paper, we reviewed the recent trends of the power devices based on WBG semiconductors as well as expected future technology. We also presented an overview of the recent package module and fabrication technologies such as direct bonded copper and active metal brazing technology. In addition, the recent heat management technologies of the power modules, which should be improved due to the increased power density in high temperature environments, are described.

• 전기전자학회논문지
• /
• 제23권2호
• /
• pp.375-379
• /
• 2019

Zn와 Sn의 원자비가 2:1인 타겟을 고주파 스파터링하여 $ZnO-SnO_2(ZTO)$박막을 증착하고 열처리에 따른 구조적 특성변화를 조사하였다. 이 ZTO박막을 활성층으로 사용하여 투명박막트랜지스터(TTFT)를 제조하였다. 약 100 nm 두께의 $SiO_2$위에 100 nm의 $Si_3N_4$막을 기른 후 TTFT의 게이트 절연막으로 채택하였다. TTFT의 전달 특성을 통해 이동도, 문턱전압, 작동전류-차단전류 비($I_{on}/I_{off}$), 계면트랩밀도를 구하였다. 기판 가열 및 후속 열처리가 ZTO TTFT의 특성 변화에 미치는 영향을 분석하였다.

• 한국표면공학회지
• /
• 제52권2호
• /
• pp.96-102
• /
• 2019

Magnesium and its alloys are prone to be corroded, thus surface treatments improving corrosion resistance are always required for practical applications. As a surface treatment of magnesium alloys, plasma electrolytic oxidation (PEO), creating porous stable oxide layer by a high voltage discharge in electrolyte, enhances the corrosion resistance. However, due to superhydrophilicity of the porous oxide layer, which easily allow the penetration of corrosive media toward magnesium alloys substrate, post-treatments inhibiting the transfer of corrosive media in porous oxide layer are required. In this work, we employed a hydrophobizing method to enhance the corrosion resistance of PEO treated Mg alloy. Three types of hydrophobizing techniques were used for PEO layer. Thin Teflon coating with solvent evaporation, self-assembled monolayer (SAM) coating of octadecyltrichlorosilane (OTS) based on solution method and SAM coating of perfluorodecyltrichlorosilane (FDTS) based on vacuum method significantly enhances corrosion resistance of PEO treated Mg alloy with reducing the contact of water on the surface. In particular, the vacuum based FDTS coating on PEO layer shows the most effective hydrophobicity with the highest corrosion resistance.

• 한국전기전자재료학회논문지
• /
• 제34권2호
• /
• pp.99-104
• /
• 2021

Ion-beam sputtering (IBS) was used to deposit semiconducting IZTO (indium zinc tin oxide) thin films onto heavily-doped Si substrates using a sintered ceramic target with the nominal composition In0.4Zn0.5Sn0.1O1.5, which could work as a channel layer for oxide TFT (oxide thin film transistor) devices. The crystallization behavior and electrical properties were examined for the films in terms of deposition parameters, i.e. target tilt angle and substrate temperature during deposition. The thickness uniformity of the films were examined using a stylus profilometer. The observed difference in electrical properties was not related to the degree of crystallization but to the deposition temperature which affected charge carrier concentration (n), electrical resistivity (ρ), sheet resistance (Rs), and Hall mobility (μH) values of the films.

• 한국전자파학회논문지
• /
• 제20권4호
• /
• pp.323-332
• /
• 2009

본 논문에서는 기존의 $\lambda_0$/4 단락 스터브 대역 통과 필터의 특성을 개선하여 LTCC(Low Temperature Co-fired Ceramic)을 이용하여 UWB(Ultra Wideband) 응용에 적합한 필터 기술을 소개한다. 높은 유전 상수의 기판($\varepsilon_r$ = 40)상에 기존의$\lambda_0$/4의 단락 스터브 대역 통과 필터 기술을 적용하기 위하여 기존의 필터와는 다르게 낮은 특성 임피던스 선로를 이용하여 결과적으로 스터브의 수를 다섯 개에서 두 개로 감소시켰다. 또한, 3개의 단락 결합 선로를 이용해서 5.15 GHz에서 5.825 GHz의 주파수 범위에서 WLAN(Wireless Local Area Network) 저지 대역을 특성 내에 삽입하였다. 본 필터는 통과 대역에서 1 dB 미만의 삽입 손실과 10 dB 이상의 반사 손실을 갖는 것으로 측정되었고, 109.49 %의 대역폭 율이 달성되었다. 측정 결과는 시뮬레이션 결과와 잘 일치한다. 필터의 크기는 $4{\times}8{\times}0.57\;mm^3$이다.