• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.888-895
• /
• 2000

As conventional grouting materials for the sheath such as cement slurry or cement-mortar are mixed and pumped in site, those harden with bleeding or shrinkage and meets low compressive strength. Also the materials haven't always same cements, sand size distributions, additives in site, so those materials have unstable quality properties. We have studies on ready-mixed-mortar for grouting pretensioned or post-tensioned cables and rods to encapsulate the steel so that we have developed a formulation of specially selected, flowable, shrinkage-compensating materials.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 춘계 학술발표회
• /
• pp.836-843
• /
• 2009

The Water Glass grouting method has been applied frequently to impermeable grouting in practice. But there is raising problems which are durability decrease by passage time and environmentally adverse effect. So, Earth Natural Grouting method which uses micro cement is developed to overcomes the problems of the Water Glass grouting method. And it is displayed ground injection extent like Water Glass grouting method. For verifying impermeability of ENG, it is carried out a triaxial permeability test about manufacturing specimen of ENG, SGR method which is a presentative Water Glass grouting method. Although Coefficient of permeability, k, of SGR is measured a little high than k of ENG whose value is $a{\times}10^{-6}cm/sec$, the value of ENG belong to impermeable rage. And, k of SGR shows relatively rapid increase according to cure time due to durability decrease of water glass. Also, in-situ test result of ENG has similar value with SGR method for similar ground.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 지반공학 공동 학술발표회
• /
• pp.188-197
• /
• 2005

Square patterned jet grouting technique is the soil improvement method that shakes the special end monitor left and right like as tail fin and mixing the soil and cement paste after cutting the soil in square shape by injecting the cement paste from installed two nozzles. The structure shape by jet grouting technique can be constructed in various shapes and sizes like as square, circle, and sector form designed by an engineer. Also, it can be constructed without waste material and reduced a construction time of work economically. In this study, the applicability of Square Jet Grouting to reduce permeability is estimated by FEM analysis and in-situ test in many cases which are various coefficient of permeability and breadth of grouting structure.

• Geomechanics and Engineering
• /
• 제12권5호
• /
• pp.739-752
• /
• 2017

This study was intended to evaluate the improved strength of the ground by applying the bio grouting method to a loose sandy ground. The injection material was prepared in the form of cement-like powder, with the bio injection material produced by microbial reactions. The grouting test was conducted under the conditions similar to the field where the bio injection material can be applied. In addition, the injection materials (cement and sodium silicate No. 3) used for Labile Waterglass (LW) method and the conventional grouting methodwere prepared through a two-solution one-step process. The injection into the specimens was done at a pressure of 150 kPa and then, with a bender element, their moduliof elasticity were measured on the 7th, 14th, 21st and 28th curingdays to analyze their strengths according to the duration of curing. It was confirmed that in all injection materials the moduli of elasticity increased over time. In particular, when 30% of the bio injection material was added to 100% cement, the modulus of elasticity tended to increase by about 15%. This confirmed that the applicability became higher when the bio injection material was used in place of the conventional sodium silicate.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 지반공학 공동 학술발표회
• /
• pp.581-590
• /
• 2005

The grouting method is widely used as the impermeable effect and ground reinforcement in construction. But, it has a problem that cement and grout material are not mixed well in the injection tip equipment and an opposite flow and interception state of the chemical grouting is happened. so, continuous work is difficult. McG method installed a special grouting and device, made possible go well mixing of grouting material and prevent flowing backward and block of nozzle also diversify powder rate of cement that is grouting material to select sutible material in layer conditions. YSS that lowered $Na_2O$ influencing durability and circumstance is developed by gel-forming reaction material. so eco-circumstance and durability is increased by minimizing dissolution of underground water. In this study, it is assumed that seepage state of the injection material using a special injection tip equipment and a unconfined compressive strenth by mixing a various injection material of various. And it is confirmed that strenth increase effect and permeable decrease of the improved body through the test execution and field execution.

• 한국지반신소재학회논문집
• /
• 제17권4호
• /
• pp.1-10
• /
• 2018

쏘일네일링 공법은 일반적으로 중력식 그라우팅 방법으로 사용되고 있으나, 그라우팅으로 인한 공동발생 및 충진 불량 문제를 해결하고자 최근에는 가압식 쏘일네일링 공법의 개발과 적용사례가 증가하고 있다. 가압식 그라우팅은 일반적으로 포틀랜트 시멘트와 물을 혼합하여 사용하나 소요강도 발현까지 10일 이상 걸리기 때문에 초속경 시멘트를 혼합하여 사용하고 있다. 이에 이 논문에서는 가압식 그라우팅 주입시간을 고려하여 적정 겔타임이 확보되는 초속경 시멘트 혼합비 30%가 가압식 쏘일네일링을 하기에 적합하다고 판단하였다. 화강풍화토 지반을 대상으로 모형토조를 제작하여 네일체의 인발실험을 한 결과, 주입시간 10초에서는 변형률 15% 일 때의 인발력이 5.7kN으로 중력식과 비교하였을 때 약 1.5배의 보강효과가 나타났다. 압력시간을 10초, 20초, 30초, 40초의 조건으로 달리할 경우에는 주입시간 증가에 따른 마찰저항력이 선형적으로 증가하나, 한계주입압력을 넘는 수준의 주입시간에서는 수압파쇄 효과로 인해 마찰저항력이 감소하는 것을 확인하였다. 또한, 수치해석을 통하여 무보강 사면과 중력식, 가압식 쏘일네일링으로 보강된 사면의 안정을 비교분석 하였다.

• 한국지반환경공학회 논문집
• /
• 제4권4호
• /
• pp.45-51
• /
• 2003

암반 내에서 주입재는 토사지반에서와는 달리 절리면을 따라 맥상으로 주입되며 그 결과 암반 내의 불연속면의 특성을 변화시키게 된다. 그러므로 그라우팅 후 암반의 변형특성은 주입재가 주입되는 절리의 방향, 절리의 특성, 그리고 현지암반의 응력상태에 따라 달라지게 된다. 즉 그라우팅에 의한 보강효과를 정확히 평가하기 위해서는 암반 내의 불연속면의 특성과 주입재의 특성이 암반의 변형거동에 미치는 영향을 규명하여야 한다. 그러나 현재까지 현장에서 적용되고 있는 그라우팅공법은 시공자의 경험에 의존하고 있으며, 그 효과에 대한 검증도 현장에서의 탄성파속도 측정, 투수시험 등을 통하여 평가하고 있다. 따라서, 본 연구에서는 그라우팅에 의한 댐 기초 암반절리면의 전단변형특성을 파악하기 위해서 자연암석 절리면에 OPC(Ordinary Portland Cement)와 Micro Cement를 각각 주입하여, 주입재의 종류, 절리면 거칠기의 평균진폭(a)에 대한 주입두께(t)를 변화시켜가면서 암석절리면 직접전단시험을 실시한 실험결과들을 비교 분석하여 최대전단강도, 잔류전단강도 등의 전단특성에 미치는 영향에 대하여 검토하였다.

• Geomechanics and Engineering
• /
• 제34권2호
• /
• pp.155-171
• /
• 2023

Aiming at the grouting treatment of water inflow in karst conduits, a visualized experiment system for conduit-type grouting blocking was developed. Through the improved water supply system and grouting system, and the optimized multisource information monitoring system, the real-time observation of diffusion and deposition of slurry, and the data acquisition of pressure and velocity during the whole process of grouting were realized, which breaks through the problem that the monitoring element is easy to fail due to slurry adhesion in conventional test system. Based on the grouting experiments in static and flowing water, the diffusion and deposition behavior of the quick-setting slurry under different working conditions were analyzed. The temporal and spatial variation behavior of the pressure and velocity were studied, and the blocking mechanism of the grouting were further revealed. The results showed that: (1) Under the flowing water condition, the counter-flow diffusion distance of slurry was negatively correlated with the flow water velocity and the volume ratio of cement and sodium silicate (C-S ratio), and positively correlated with the grouting volume. The slurry deposition thickness was negatively correlated with the flowing water velocity, and positively correlated with the grouting volume and C-S ratio. (2) The pressure increased slowly before blocking of the flowing water and rapidly after blocking in karst conduits. (3) With the continuous progress of grouting, the flowing water velocity decreased slowly first, then significantly, and finally tended to be stable. According to the research results, some engineering recommendations were put forward for the grouting treatment of the conduit-type water inflow disaster, which has been successfully applied in the treatment project of the China Resources Cement (Pingnan) Limestone Mine. This study provided some guidance and reference for the parameter optimization of grouting for the treatment projects of water inflow in karst conduits.

• Geomechanics and Engineering
• /
• 제20권1호
• /
• pp.67-73
• /
• 2020

With the increasing number of underground projects, the problem of rock-water coupling catastrophe has increasingly become the focus of safety. Grouting reinforcement is gradually applied in subway, tunnel, bridge reinforcement, coal mine floor and other construction projects. At present, cement-based grouting materials are easy to shrink and have low strength after solidification. In order to overcome the special problems of high water pressure and high in-situ stress in deep part and improve the reinforcement effect. In view of the mining conditions of deep surrounding rock, a new type of cement-based reinforcement material was developed. We analyses the principle and main indexes of floor strengthening, and tests and optimizes the indexes and proportions of the two materials through laboratory tests. Then, observes and compares the microstructures of the optimized floor strengthening materials with those of the traditional strengthening materials through scanning electron microscopy. The test results show that 42.5 Portland cement-based grouting reinforcement material has the advantages of slight expansion, anti-dry-shrinkage, high compressive strength and high density when the water-cement ratio is 0.4, the content of bentonite is 4%, and the content of Nano Silica is 2.5%. The reinforcement effect is better than other traditional grouting reinforcement materials.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.137-144
• /
• 2005

Recently a pressurized grouting soil nail is demanded due to problems beyond of economical and engineering purpose. In this study, a newly modified soil nailing technology named as the PGSN (Pressurized Grouting Soil Nailing) system is respected to reduced displacements of nails and increase of global slope stability. And effects of various factors related to the design of the PGSN system, such as the length of the soil nail, injected pressure and W/C ratio of cement grout in the pressurized grouting soil nail are examined throughout a series of the displacement-controlled field pull-out tests. Displacement-controlled field pull-out tests are performed in the present study and the volume of grouting are also evaluated based on the measurements. In addition, both short-term and long-term characteristics of pull-out deformations of the newly proposed PGSN system are analyzed and compared with those of the general soil nailing system by carrying out the stress-controlled field pull-out tests. From the pull-out characteristics of pressurized grouting soil nails, it is found that the effect of the length of the soil nail, injected pressure and W/C ratio of cement grout are important parameters.