• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.27 no.3
• /
• pp.180-186
• /
• 2017

Objectives: The purposes of this study were to compare the surface resistance of cassettes according to the material, and to evaluate the wall deposition of carbon nanotubes(CNTs) by electrostatic loss in the inner wall of the cassette. Methods: Surface resistance was measured for three types of cassettes(25 mm polypropylene conductive cowl, 25 mm and 37 mm clear styrene cassettes) with a surface resistance meter. Also, electrostatic wall loss was measured at different weights of CNTs depending on the cassette. CNTs were laid on a weight dish with the cassette for five minutes to provide sufficient time to attach on the wall. Wipe sampling was performed to collect CNTs deposited on the wall and elemental carbon, known as a surrogate for CNTs, was analyzed. Results: The cassette with conductive materials(18% of black carbon) showed the lowest surface resistance($<1.21{\times}10^3{\Omega}$). Cassettes made from clear polystyrene showed the relatively highest surface resistance(25 mm: $10.02{\times}10^9{\Omega}$, 37 mm: $10.59{\times}10^9{\Omega}$). This means that particles are more likely to stick to the internal wall of styrene cassettes due to electrostatic electricity. This may lead to an underestimation of the airborne concentration of CNTs. The experiment showed that EC was not detected when using a 25 mm conductive cowl cassette, while EC was detected at the internal wall of 25 mm and 37 mm polystyrene cassettes. Conclusions: This study confirms that cassettes with a conductive cowl have low surface resistance and are more appropriate for CNT sampling. In addition, this finding could be applied for other types of particulate, especially regarding electrostatic charge and sampling.

• International Journal of Aeronautical and Space Sciences
• /
• v.12 no.2
• /
• pp.115-133
• /
• 2011

Fiber reinforced polymer composites (FRPs) are being increasingly used for a wide range of engineering applications owing to their high specific strength and stiffness. However, their through-the-thickness performance lacks some of the most demanding physical and mechanical property requirements for structural applications, such as aerospace vehicles and military components. Carbon nanotubes (CNTs) and carbon nanofibers (CNFs), due to their excellent mechanical, thermal and electrical properties, offer great promise to improve the weak properties in the thickness direction and impart multi-functionality without substantial weight addition to FRPs. This paper reviews the progress made to date on i) the techniques developed for integration of CNTs/ CNFs into FRPs, and ii) the effects of the addition of these nanofillers on the interlaminar properties, such as such interlaminar shear strength, interlaminar fracture toughness and impact damage resistance and tolerance, of FRPs. The key challenges and future prospects in the development of multiscale CNT-FRP composites for advanced applications are also highlighted.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.6
• /
• pp.615-620
• /
• 2013

There is considerable interest in developing energy sources capable of larger power densities. In our previous works, we proved that by coupling an exothermic chemical reaction with 1D nanostructures, a self-propagating reactive wave can be driven along its length with a concomitant electrical pulse of high specific power, which we identified as a thermopower wave. Herein, we discuss details about many different aspects of a thermopower wave. Different alignment degree in vertically aligned CNT films is evaluated in the reactive wave speed and correlated with its thermal reaction that affects the change in the magnitude of energy generation. The effects of the temperature-dependent properties of chemical fuels and CNTs are evaluated. Furthermore, we explore the convection and radiation portions in this thermal wave as well as the synchronization between the thermal reaction transfer and the oscillation of the electrical signal.

• Korean Chemical Engineering Research
• /
• v.60 no.2
• /
• pp.184-192
• /
• 2022

Porous NiO synthesized via hydrothermal synthesis was used in the electrodes of lithium-sulfur batteries to inhibit the elution of lithium polysulfide. The electrode of the lithium-sulfur battery was manufactured as a freestanding flexible electrode using an economical and simple vacuum filtration method without a current collector and a binder. The porous NiO-added S/CNT/NiO electrode exhibited a high initial discharge capacity of 877 mA h g^-1 (0.2 C), which was 125 mA h g^-1 higher than that of S/CNT, and also showed excellent retention of 84% (S/CNT: 66%). This is the result of suppressing the dissolution of lithium polysulfide into the electrolyte by the strong chemical bond between NiO and lithium polysulfide during the charging and discharging process. In addition, for the flexibility test of the S/CNT/NiO electrode, the 1.6 × 4 cm² pouch cell was prepared and exhibited stable cycle characteristics of 620 mA h g^-1 in both the unfolded and folded state.

• Clean Technology
• /
• v.29 no.3
• /
• pp.178-184
• /
• 2023

Transition metal chalcogenides have garnered significant attention as anode materials for sodium-ion batteries due to their high theoretical capacity. Nevertheless, their practical application is impeded by their limited lifespan resulting from substantial volume expansion during cycling and their low electrical conductivity. To tackle these issues, this study devised a solution by synthesizing a nanostructured anode material composed of porous CNT (carbon nanotube) spheres and (Ni,Co)Se₂ nanocrystals. By employing spray pyrolysis and subsequent heat treatments, a porous-structured (Ni,Co)Se₂-CNT composite microsphere was successfully synthesized, and its electrochemical properties as an anode for sodium-ion batteries were evaluated. The synthesized (Ni,Co)Se₂-CNT microsphere possesses a porous structure due to the nanovoids that formed as a result of the decomposition of the polystyrene (PS) nanobeads during spray pyrolysis. This porous structure can effectively accommodate the volume expansion that occurs during repeated cycling, while the CNT scaffold enhances electronic conductivity. Consequently, the (Ni,Co)Se₂-CNT anode exhibited an initial discharge capacity of 698 mA h g^-1 and maintained a high discharge capacity of 400 mA h g^-1 after 100 cycles at a current density of 0.2 A g^-1.

• Korean Chemical Engineering Research
• /
• v.61 no.3
• /
• pp.426-438
• /
• 2023

Lithium-sulfur batteries, recently attracting attention as next-generation batteries, have high energy density but are limited in application due to sulfur's insulating properties, shuttle phenomenon, and volume expansion. This study used an economical and simple vacuum filtration method to prepare a freestanding electrode without a binder and collector. Carbon nanotubes (CNTs) are used to improve the electrical conductivity of sulfur, where CNT also acts as both collector and conductor. In addition, metal oxides (MO_x, M=Ni, Mg), which are easy to adsorb lithium polysulfide, are added to the CNT/S electrode to suppress the shuttle reaction in lithium-sulfur batteries, which is a result of suppressing the loss of active sulfur material due to the excellent adsorption of lithium polysulfide by metal oxides. The MO_x@CNT/S electrode exhibited higher capacity characteristics and cycle stability than the CNT/S electrode without metal oxides. Among the MO_x@CNT/S electrodes, the NiO@CNT/S electrode displayed a high discharge capacity of 780 mAh g^-1 at 1 C and an extreme capacity decrease to 134 mAh g^-1 after 200 cycles. Although the MgO@CNT/S electrode exhibited a low discharge rate of 544 mAh g^-1 in the initial cycle, it showed good cycle stability with 90% of capacity retention up to 200 cycles. Further, to achieve high capacity and cycle stability, the Ni_0.7Mg_0.3O@CNT/S electrode, mixed with Ni:Mg in the ratio of 0.7:0.3, manifested an initial discharge rate of 755 mAh g^-1 (1 C) and a capacity retention rate of more than 90% after 200 cycles. Therefore, applying binary metal oxides to CNT/S provides a freestanding electrode for developing economical and high-performance Li-S batteries, effectively improving lithium polysulfide's high capacity characteristics and dissolution.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.93-93
• /
• 2000

수소화된 비정질 탄소(a-C:H)는 그 증착 조건에 따라서 여러 가지 다른 구조와 특성을 갖게 되며, 특히 DLC(diamond-like carbon) 및 CNT(Carbon nanotube)는 FED (field emission display) 개발 면에서 중요하게 연구되고 있다. 우리는 a-C:H 박막을 PECVD (plasma-enhanced chemical vapor deposition) 방법으로 증착하고 CH4 가스를 사용하였고 기판 온도는 상온-32$0^{\circ}C$ 사이에서 변화되었다. 기판은 Corning 1737 glass, quartz, Si, Ni 등을 사용하였다. 증착 압력과 R.F. power는 각각 0.1-1 Torr 와 12-60w 사이에서 변화되었다. ESR 측정은 X-band(주파수 약 9 GHz)에서 그리고 상온에서 행해졌다. 상온에서의 스핀밀도는 약한-표준피치(weak-pitch standard) 스펙트럼과 비교하여 얻을 수 있었다. 그리고 a-C:H 박막의 구조는 He-Ne laser(파장 632.8 nm)를 이용하는 micro-Raman spectroscopy로 분석하였다. 증착조건에 따른 스핀밀도의 변화 및 Raman 스펙트럼에서의 D-peak, G-peak의 위치 및 반치록, I(D)/I(G) 등을 조사하였다. 증착된 a-C:H 박막은 R.F.power가 증가할수록 대체로 스핀밀도가 증가하였으며, Raman 스펙트럼에서의 I(D)/I(G) 비율은 대체로 감소하였다. 증착된 박막들은 polymer-like Carbon으로 추정되었으며, 스핀밀도가 증가할수록 대체적으로 흑연 구조 영역이 증가됨을 알 수 있었다. 또한 glass나 Si 기판에 비해 Ni 기판위에서 polymer-like Carbon 구조는 향상되는 경향을 보였다.

• Journal of Powder Materials
• /
• v.29 no.4
• /
• pp.297-302
• /
• 2022

This study compares the characteristics of a compact TiO₂ (c-TiO₂) powdery film, which is used as the electron transport layer (ETL) of perovskite solar cells, based on the manufacturing method. Additionally, its efficiency is measured by applying it to a carbon electrode solar cell. Spin-coating and spray methods are compared, and spray-based c-TiO₂ exhibits superior optical properties. Furthermore, surface analysis by scanning electron microscopy (SEM) and atomic force microscopy (AFM) exhibits the excellent surface properties of spray-based TiO₂. The photoelectric conversion efficiency (PCE) is 14.31% when applied to planar perovskite solar cells based on metal electrodes. Finally, carbon nanotube (CNT) film electrode-based solar cells exhibits a 76% PCE compared with that of metal electrode-based solar cells, providing the possibility of commercialization.

• Science of Emotion and Sensibility
• /
• v.24 no.2
• /
• pp.65-74
• /
• 2021

With recent innovations in the ICT industry, the demand for wearable sensing devices to recognize and respond to biological signals has increased. In this study, a three-dimensional (3D) spacer fabric was embedded in a single-wall carbon nanotube (SWCNT) dispersive solution through a simple penetration process to develop a monolayer piezoresistive pressure sensor. To induce electrical conductivity in the 3D spacer fabric, samples were immersed in the SWCNT dispersive solution and dried. To determine the electrical properties of the impregnated specimen, a universal testing machine and multimeter were used to measure the resistance of the pressure change. Moreover, to examine the changes in the electrical properties of the sensor, its performance was evaluated by varying the concentration, number of penetrations, and thickness of the specimen. Samples that penetrated twice in the SWCNT distributed solution of 0.1 wt% showed the best performance as sensors. The 7-mm thick sensors showed the highest GF, and the 13-mm thick sensors showed the widest operating range. This study confirms the effectiveness of the simple process of fabricating smart textile sensors comprising 3D spacer fabrics and the excellent performance of the sensors.

• The Journal of the Convergence on Culture Technology
• /
• v.4 no.3
• /
• pp.287-291
• /
• 2018

The CNTFET, which is attracting attention as a next-generation semiconductor device, can obtain ballistic or near-ballistic transport at a lower voltage than that of conventional MOSFETs by depositing CNTs between the source and drain of the device. In order to increase the performance of the CNTFET, a large number of CNTs must be deposited at a high density in the CNTFET. Thus, various manufacturing processes to increase the density of the CNTs have been developed. Recently, the Directional Shrinking Transfer Method was developed and showed that the current density of the CNTFET device could be increased up to 150 uA/um. So, this method enhances the possibility of implementing a CNTFET-based integrated circuit. In this paper, we will discuss how to evaluate the performance of the CNTFET device compared to a MOSFET at the circuit level when the CNTFET is fabricated by the Directional Shrinkage Transfer Method.