• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.7
• /
• pp.1282-1288
• /
• 2010

This paper proposes a novel microstrip patch antenna to make impedance matching possible by using slot/T-slot capacitive coupling between the patch and 50 $\Omega$ feed line on a ground plane. The single band/linear polarization patch antenna shows linear polarization at 2.4 GHz band. Under -10 dB return loss, the single band/linear polarization patch antenna obtains 50 MHz bandwidth at 2.37 GHz~2.42 GHz. The dual band/dual polarization microstrip patch antenna shows circular polarization at 2.4 GHz band and linear polarization at 3.1 GHz band. Under -10 dB return loss, The dual band/dual polarization microstrip patch antenna obtains 340 MHz bandwidth at 2.23~2.57 GHz and 375 MHz bandwidth at 2.95~3.325 GHz.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.59 no.3
• /
• pp.317-324
• /
• 2010

It was used as measuring system to diagnose insulating condition, by which was kept a insulating resistance of inner stack and at the same time was cooled electrochemical heat of reaction of FCEV(fuel cell electric vehicle) stack that used a compressed hydrogen gas reacting with oxygen in accordance with variation on thermal degradation of nonconductive heat transfer fluid. Consequently it was developed a cylindrical multi-terminal capacitive-conductive sensor that could be attached to the internal surface of cooling system pipe to evaluate capacitance and conductivity of heat transfer fluid.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.9
• /
• pp.786-791
• /
• 2009

Transformer failures are mostly due to partial discharges (PDs) caused by the deteriorated insulation. It is, therefore, important to monitor PD occurrence in insulation system and prevent their deterioration. The presented paper deals with a PD detection method by a capacitive probe, which easily apply to cast - resin dry - type transformers. The PD detection system consists of a capacitive probe and a low noise amplifier having the frequency bandwidth of 500 $Hz{\sim}30$ MHz. In the experimental set-up, sensitivity of the system is 7.16 mV/pC.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.3
• /
• pp.406-412
• /
• 1998

This paper describes a contact position detection method of a capacitive touch screen panel. The proposed method is composed of a circuited compensating algorithm generating an output signal having phase difference to an input signal associated with contact position, converts both input and output signals into digital waveform (5V logic), and calculates the phase difference. Finally, position information with the phase difference is obtained by using a low-cost microprocessor, which is convenient to compensate non-linearity error. The proposed method, that computes phase difference directly, has advantages in feasibility and cost because it minimizes the use of analog devices; rather, it utilizes, cost effective digital circuit. Analytical results are also given.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.1
• /
• pp.23-32
• /
• 2011

A 40 fJ/c-s, 1 V, 10-bit SAR ADC is presented for energy constrained wearable body sensor network application. The proposed 10-bit dual sampling capacitive DAC topology reduces switching energy by 62% compared with 10-bit conventional SAR ADC. Also, it is more robust to capacitor mismatch than the conventional architecture due to its cancelling effect of each capacitive DAC. The proposed SAR ADC is fabricated in 0.18 ${\mu}m$ 1P6M CMOS technology and occupies 1.17 $mm^2$ including pads. It dissipates only 1.1 ${\mu}W$ with 1 V supply voltage while operating at 100 kS/s.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.569-575
• /
• 2001

The three-phase diode rectifier with capacitive Inter is highly sensitive to line voltage unbalance. Because of its inherent nonlinear characteristics small line voltage unbalance may cause highly unbalanced line current causing detrimental effects on power quality. This paper presents a theoretical basis on this 'unbalance amplification effect' and derives an analytical model of line current characteristics under unbalanced line voltage condition for various modes of operation. The results provide a basic and important guideline for optimal design of a three-phase diode rectifier with capacitive filter that is most commonly used for interfacing various power conversion equipments to power lines.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.476-477
• /
• 2007

This paper described the partial discharge (PD) measurement techniques for diagnosing gas-insulated switches in overhead power distribution system. A capacitive voltage probe to detect PD pulse was designed and fixed on the surface of a bushing. We also designed a coupling network to attenuate AC voltage by 270 dB, and a low-noise amplifier having the gain of 40 dB and 500 kHz~20 MHz 3 dB. From the calibration, it was calculated that the sensitivity of the measurement system was 0.94mV/pC. In the application experiment, we could measure a PD pulse of 45 pC.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.8
• /
• pp.1397-1404
• /
• 2007

It is important to measure the resistive component separately from the total leakage current at power distribution line. It is because electric disasters such as electric shock and fire are caused mainly by the resistive component of the total leakage current. In this paper, a new theory for measuring the resistive component separately from the total leakage current is suggested, and is embodied to an actual circuit using operational amplifiers, analog switch and R-C low pass filter. Through experiments for various cases containing both the resistive and capacitive leakage currents, the suggested algorithm is confirmed to be able to measure the resistive leakage current within 4.1% of error even when the capacitive leakage current is much bigger than the resistive one. The suggested method is expected to lower the total cost because it can be realized using simple and cheap devices, and implies the measuring time can be possibly reduced because the resistive leakage current is computed exactly from the signals during only a half period of power voltage.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.561-564
• /
• 2000

Silicon capacitive pressure sensor has been fabricated by using electrochemical etching stop and silicon-to-glass electrostatic bonding technique. A diaphragm structure is designed to compensate the nonlinear response. A cavity is etched into the silicon to the depth of 2$\mu\textrm{m}$ by anisotropic etching in 20wt.% TMAH solution at 80$^{\circ}C$. A fabricated sensor showed 3.3 pF zero-pressure capacitance, 297 pp.m/mmHg sensitivity, and a 7.4 7%F.S. nonlinear response in a 0-1 kgf/cm$^2$pressure range.

• Journal of the Korean institute of surface engineering
• /
• v.52 no.5
• /
• pp.239-245
• /
• 2019

To increase the throughput of tip-based nanolithography (TBN), one approach is to use a large array of such tips working in parallel. It is important to maintain co-planarity between the tip array and the writing surface. A slight misalignment can cause large discrepancies of contact force and feature sizes. We report a capacitive proximity sensor built-in with the TBN array for leveling an arrayed polymer pen array. The device allows alignment between an array of writing tips and the writing substrate without contact and contamination. The angular sensitivity of the sensor is $0.05^{\circ}$ for an array with maximum tip-to-tip separation of 100 mm.