• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.3
• /
• pp.69-75
• /
• 2016

This study investigated the effect of heat treatment conditions not only on the Cr surface crack propagation behaviors but also on the Ni/Cr interfacial reaction characteristics in electroless Ni/electroplated Cr double coating layers on Cu substrate. Clear band layer of Ni-Cr solid solutions were developed at Ni/Cr interface after heat treatment at $750^{\circ}C$ for 6 h. Channeling cracks formed in Cr layer after 1 step heat treatment, that is, heat treatment after Ni/Cr plating, while little channeling cracks formed after 2 step heat treatment, that is, same heat treatments after Ni and Cr plating, respectively, due to residual stress relaxation due to crystallization of Ni layer before Cr plating.

• Journal of the Korean Magnetics Society
• /
• v.8 no.6
• /
• pp.374-379
• /
• 1998

$Mn_1-xCr_xPt_3$ alloy films have been prepared by depositing (Mn, Cr)/Pt multilayers using a rf magnetron sputterer followed by heat treatment. Small and wide angle x-ray diffractometry, magnetic hysteresis loops and Kerr rotation angle spectra of the films have been measured and used to investigate structural, magnetic and magneto-optic properties of the films. The films had a crystal structure of ordered AuCu$_3$ type and the strong preferred orientation of a (111)plane parallel to the film surface. The saturation magnetization of the films was decreased with Cr content reaching almost zero near x=0.58 and then increased for further increasement of Cr content up to x=0.77 over that stayed almost constant. This indicated that Cr atoms were antiferromagnetically coupled with Mn atoms. The magnetic easy axis of MnPt$_3$(x=0) film was parallel to the film surface but those of the films with x$\geq$0.58 increased as Cr content increased reaching about 4 kOe at x=1(CrPt$_3$). The dependence of the Kerr rotation angle on the Cr content was similar to that of the saturation magnetization on the Cr content. The films with x=0.77 and x=1 showed the larger Kerr rotation angle at the wavelengths of near infrared compared to the magneto-optic recording medium, TbFeCo, currently being used.

• Journal of the Korean Magnetics Society
• /
• v.15 no.5
• /
• pp.257-260
• /
• 2005

We investigated the half-metallicity and magnetism for the zinc-blende CrS(001) surfaces by use of the full-potential linearized augmented plane wave (FLAPW) method. We considered two-types of (001) surfaces terminated by Cr (Cr-Term) and S (S-Term) atoms, respectively. From the calculated layer-by-layer density of states, it is found that both of the systems retain the half-metallicity at the (001) surfaces. The calculated magnetic moment ($4.07\;{\mu}_B$) for the CrS(S) atom in Cr-Term is enhanced considerably compared to the bulk value ($3.61\;{\mu}_B$) while that ($3.15\;{\mu}_B$) of the Cr(S-1) in S-Term is much reduced.

• Journal of the Korean Chemical Society
• /
• v.33 no.2
• /
• pp.164-167
• /
• 1989

The rate for the aquation of $trans-[Cr(tmd)_2FX]^+(X=F^-,\;Cl^-)$ ion in aqueous acidic solution has been measured by spectrophotometric method at various temperatures and pressures. The rate constants are increased with increasing temperatures and pressures. The values of activation entropy are 5.2 eu for $trans-[Cr(tmd)_2F_2]^+$ and -16.62 eu for $trans-[Cr(tmd)_2FCl]^+$ ions. Activation volumes have all negative values and lie in the limited range $-3∼-2\;cm^3mol^{-1}$ for $trans-[Cr(tmd)_2F_2]^+$ and $-8∼-7\;cm^3mol^{-1} for $trans-[Cr(tmd)_2FCl]^+$ ion. From the above results, we may deduce that the mechanism for the aquation of $trans-[Cr(tmd)_2F_2]^+$ and $trans-[Cr(tmd)_2FCl]^+$ ions is interchange-associative mechanism and dissociative mechanism respectively.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.46.2-46.2
• /
• 2009

휴대전화, 랩톱 컴퓨터 등 각종 모바일기기 및 디스플레이 기기의 경박단소화 및 고기능화에 따라 연성회로기판(FPCB)의 사용량이 증가하고있다. 연성회로기판의 핵심소재인 동박적층필름(FCCL)은 폴리이미드필름과 접착층, Cu 층으로 구성되는데, 이 중접착층으로 사용되는 Ni-20Cr합금은 에칭공정 후 Cr의 잔류에 의해 불량률 증가가 문제되고 있어, Ni-Cr합금 스퍼터링 타깃의 Cr 함량 저감 또는 Cr-free Ni합금 개발 등이 요구되고 있다. 본 연구에서는 차세대 FCCL 본드층에 적합한 Ni기 합금을 개발하기 위한 기초연구로써 Cr 함량 및 가공열처리조건에 따른 미세조직과 집합조직 변화를 조사하였다. 4N급의 고순도Ni과 Cr을 진공 플라즈마 용해장치로 용해하여Ni-xCr (x=5, 10, 15, 20wt.%)합금 잉곳을 만들고, 이를 두께감소율 90%로 냉간압연한 후, $600^{\circ}C$ 및 $800^{\circ}C$에서 10~120분 동안 어닐링하여 시편을 준비하였다. 광학현미경으로 미세조직을 관찰하고, Micro-Vickers 경도시험을 통해 어닐링 조건에 따른 경도변화를 조사하였다. 또한 SEM-EBSD를 이용하여 집합조직 및 입계특성을 분석하였다. $600^{\circ}C$ 어닐링 시 Cr함량이 증가할수록 재결정 완료시간이 증가하여 Ni-20Cr합금의 경우 2시간이상 어닐링에도 재결정이 일어나지 않았다. $800^{\circ}C$ 어닐링 시 10분 어닐링 조건에서 4종류 합금 모두 재결정이 완료되었으며, 동일한 어닐링 조건에서 Cr함량이 증가할수록 결정립이 작아지는 것으로 나타났다. $800^{\circ}C$ 2시간 어닐링 조건에서 Ni-5Cr 합금의 주요 집합조직은 {223}<113>과 {122}<112>로 나타났으며, 이중 {223}<113>은Cr 함량이 증가함에 따라 점차 {122}<112>에 가까운 방향으로 변화되어 Ni-20Cr 합금의 경우 {123}<112>만이 형성되었다. 이러한 집합조직의 변화는 적층결함에너지 감소에 의한 ${\Sigma}3$ 입계의 분율 증가와 밀접한 관련이 있는 것으로 사료된다.

• Korean Journal of Materials Research
• /
• v.4 no.6
• /
• pp.704-709
• /
• 1994

The $(LaS)_xCrS_2(x \approx 1.20$) of the incommensurate misfit layer was systhesized from reactant mixture of$La_S_3$,Cr and S at 1273K. Powder X-ray diffration of $(LaS)_xCrS_2(x \approx 1.20$) was indexed as a complex structure consisted with a monoclinic LaS-sublattice, a triclinic $CrS_{2}$-sublattice and their superlattice. The temperature dependence of sublattice dimension was investigated by the X-ray diffraction analysis at low temperature. The magnetic susceptibility of $(LaS)_xCrS_2(x \approx 1.20$) was measured between 77K and room temperature using a Faraday balance method. $(LaS)_xCrS_2(x \approx 1.20$) was paramagnetic on a $\sigma$-H plot at room temperature. The observed effective magnetic moment( p dr) was in fair agreement with the value calculated by spin-only contribution for $Cr^{3+}$ and spin and orbital contribution for $La^{3+}$.

• Journal of Microbiology and Biotechnology
• /
• v.23 no.8
• /
• pp.1123-1132
• /
• 2013

The removal of toxic Cr(VI) by microorganisms is a promising approach for Cr(VI) pollution remediation. In the present study, four indigenous bacteria, named LY1, LY2, LY6, and LY7, were isolated from Cr(VI)-contaminated soil. Among the four Cr(VI)-resistant isolates, strain LY6 displayed the highest Cr(VI)-removing ability, with 100 mg/l Cr(VI) being completely removed within 144 h. It could effectively remove Cr(VI) over a wide pH range from 5.5 to 9.5, with the optimal pH of 8.5. The amount of Cr(VI) removed increased with initial Cr(VI) concentration. Data from the time-course analysis of Cr(VI) removal by strain LY6 followed first-order kinetics. Based on the 16S rRNA gene sequence, strain LY6 was identified as Pseudochrobactrum asaccharolyticum, a species that had never been reported for Cr(VI) removal before. Transmission electron microscopy and energy dispersive X-ray spectroscopy analysis further confirmed that strain LY6 could accumulate chromium within the cell while conducting Cr(VI) removal. The results suggested that the indigenous bacterial strain LY6 would be a new candidate for potential application in Cr(VI) pollution bioremediation.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.421-425
• /
• 2009

A study has been performed to investigate the thermo-mechanical effects of thermal barrier coating on liquid rocket regenerative cooling chamber using finite element analysis. Two kinds of thermal barrier coatings were studied on the same loading condition: first, NiCrAlY-$ZrO_2$, coating which is currently applied to the developing combustion chamber and second, Ni-Cr coating which might be applied in the future. Analysis results showed that NiCrAlY-$ZrO_2$ coating has better decreasing effect of temperature than the Ni-Cr coating. As a results, temperature and deformation of the cooling channel in the NiCrAlY-$ZrO_2$ coating were also less than those of the Ni-Cr coating. The Ni-Cr coating has no effect on a structural stability of the outer jacket but the NiCrAlY-$ZrO_2$ coating reduced the effective stress of the outer jacket and enhanced the structural stability of the chamber.

• Journal of the Korean Magnetics Society
• /
• v.25 no.2
• /
• pp.31-38
• /
• 2015

Recently, a first-principles study led to a prediction that quaternary Heusler compounds, CoFeCrZ (Z = Ga, Ge) are excellent half-metallic ferromagnets. In this study, we investigate the electronic and the magnetic properties at the (001) surfaces of CoFeCrGa and CoFeCrGe by means of the full-potential linearized augmented plane wave (FLAPW) method within generalized gradient approximation. We considered two types of surface termination: CoFe-terminated and CrZ-terminated surfaces, Z being either Ga or Ge. From the calculated total magnetic moments and the local density of states, we found that half-metallicity is not preserved for all the surfaces. But the calculated atomic density of states showed that CrGa-terminated surface of the CoFeCrGa is almost half-metallic. The magnetic moment of the Co, Fe, or Cr atoms at the surface or subsurface layers in each system had very different values.

• Journal of the Korean institute of surface engineering
• /
• v.43 no.5
• /
• pp.238-242
• /
• 2010

In the present work, the influence of oxide on the Cr-Si-N coatings was investigated for the Cr-Si-O-N coatings on AISI 304 and Si wafer deposited by hybrid system, which combines the DC magnetron sputtering technique and arc ion plating (AIP) using Cr and Si target in an $Ar/N_2/O_2$ gaseous mixture. As the O content in the Cr-Si-N coatings increased, the diffraction patterns of the Cr-Si-O-N coatings showed CrN and $Cr_2O_3$ phases. However, as the O content increased to 28.8 at.%, diffraction peak of $Cr_2O_3$ was disappeared in the Cr-Si-O-N coating. The $d_{200}$ value was decreased with increasing of O content. The average grain size increased from about 40 nm to 65 nm as the O content increased. The maximum micro-hardness of the Cr-Si-O-N coating was obtained 4507 Hk at the O content of 24.8 at.%. The average friction coefficient of the Cr-Si-O-N coatings was gradually decreased by increasing the O content and the average friction coefficient decreased from 0.37 to 0.25 by increasing the O content. These results indicated that amorphous phase was increased in the Cr-Si-O-N coatings by increasing of O content.