• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.4 no.2 s.7
• /
• pp.81-87
• /
• 2005

In this paper, a VCDRO(Voltage Control Dielectirc Resonator Oscillator) for signal source of doppler radar system is designed and fabricated. The proposed VCDRO is made with new tuning mechanism using CPW line. The coplanar waveguide of $\lambda_{g}$/2 in length with varactor diode is placed on the metallization side under the dielectric resonator and coupled to it. Tuning varactor diode is mounted at one end of the CPW. The proposed circuit tuned by a CPW allows one more varactor diode to be mounted on the optimized CPW, where a greater sensitivity of frequency tuning is needed. With varying the biasing voltage for the varactor diode from 0 V to 15 V, output frequency tuning of 12 MHz is obtained. The PLDRO exhibits output power of 16.5 dBm with phase noise in the phase locked state characteristic of -115 dBc/Hz at 100 Hz, -105 dBc/Hz at the 10 kHz, and -102 dBc/Hz at 1 Hz offset from 10.525 GHz , respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.12
• /
• pp.2773-2778
• /
• 2015

In this paper, the compact antenna with three folded patches for use in a number of bands of LTE, WCDMA, US-PCS, and WLAN at the same time is proposed. As the changes in widths of the 3 patches to widen the insufficient bandwidth are given, it is optimized for $S_{11}$<-6dB(VSWR<3). The CPW with a number of advantages is used in the proposed antenna. The proposed antenna is designed and fabricated with FR4 substrate to the size of $44.9{\times}35{\times}1mm^3$. Fabricated antenna has within $S_{11}$<-6dB under operating bands. And measured characteristics of radiation patterns and gains are shown under operating bands.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.4
• /
• pp.19-25
• /
• 2002

In this paper, to improve the characteristics of a transmission line on silicon substrate, we fabricated air-bridge interconnected CPW transmission line on a 10-${\mu}{\textrm}{m}$-thick oxidized porous silicon(OPS) substrate using surface micromachining. Air-bridge interconnected CPW of S-W-S = 30-80-30 ${\mu}{\textrm}{m}$has insertion loss of -0.25 ㏈ and return loss of -28.9 ㏈ at 4㎓ And return loss of CPW with stepped compensated air-bridge(S-W-S : 30-100-30 ${\mu}{\textrm}{m}$) is improved -0.98㏈ at 4㎓. The results indicate that the thick OPS provides an approach to incorporate high performance, low cost microwave and millimeter wave circuits in a high-resistivity silicon-based process.

• Journal of Advanced Navigation Technology
• /
• v.24 no.6
• /
• pp.581-586
• /
• 2020

In this paper, the design process and method for a compact wideband loop antenna for terrestrial digital TV (DTV) and ultra high definition (UHD) TV applications was proposed. Horizontal slits were added on the two circular sectors of the proposed loop antenna in order to miniaturize the existing wideband loop antenna consisting of a square loop and two circular sectors. A CPW transmission line was inserted in the center of the lower circular sector as a feed line. The CPW feed line was designed using the 75 ohm port impedance for DTV and UHD TV applications, and a tapered center-signal line was designed to improve the impedance matching. The final designed antenna was fabricated on an FR4 substrate with a thickness of 0.8 mm. The experiment results show that the proposed compact loop antenna operates in the frequency band of 444.3-820.1 MHz for a VSWR < 2, which fully covers the DTV and UHD TV bands.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.2
• /
• pp.267-272
• /
• 1999

In general, printed antennas have a narrow bandwidth characteristic and many people want to find out the method of bandwidth improvement through complicated procedures. So we want to reform the conventional printed antenna characteristic by using the folded dipole's superiority to unit dipole. But it is hard to feed the printed folded dipole antenna, we use the CPW, which is widely used in microwave IC or MMIC applications and have many advantages to the conventional microstrip line, to feed the printed folded slot antenna. It is confirmed that the improvement in the bandwidth characteristic of CPW fed folded slot antenna, as much as 20%, through the measurement of designed and implemented antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.11
• /
• pp.1248-1253
• /
• 2008

The MCS(Micro-Coplanar Strip) line with ground has been analyzed. The conformal mapping method is used to calculate the quasi-static effective dielectric constant and characteristic impedance of this MCS line. The computed results of the present work are found to be in good agreement when compared with the results obtained using commercial S/W, IE3D. And in this paper, the stepped-impedance low pass filter is designed and fabricated with MCS lines for improving the frequency responses. The LPF proposed structure has been also designed and implemented to have the sharp attenuation characteristics in stop band. The agreement between simulation and measurement results verify the implemented LPF.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.4C no.4
• /
• pp.165-169
• /
• 2004

This paper reports a miniaturized conductor-backed CPW (CBCPW) bandpass filter based on a thin film polyimide layer coated on CMOS-grade silicon. With a 20 ${\mu}{\textrm}{m}$-thick polyimide interface layer and back metallization on the CMOS-grade silicon, the interaction of electromagnetic fields with the lossy silicon substrate has been isolated, and as a result a low-loss and low-dispersive CBCPW line has been obtained. Measured attenuation constant at 20 GHz is below 1.2 ㏈/cm, which is compatible with the CPW on GaAs. In addition, by using the proposed CBCPW geometry, miniaturized BPF for Ku band application is designed and its measured frequency response shows excellent agreement with the predicted value with validating the performances of the proposed CBCPW geometry for RFIC interconnects and filter applications.

• Journal of electromagnetic engineering and science
• /
• v.2 no.2
• /
• pp.59-64
• /
• 2002

In this paper, 10$\mu$ m-elevated MEMS CPWs on various substrates are presented. Effective dielectric constants of elevated CPW(ECPW) on polyimide-loaded silicon or alumina substrate are examined and characteristic impedances are also computed versus elevation height. Dispersive property of ECPW and its electromagnetic field distributions are studied through 3-D FDTD algorithm for optimum design. Attenuation of ECPW is measured with TRL calibration procedure and revealed about 3.2 43 lower than that of conventional CPW on the same low-resistivity silicon at 40 CHz. ECPW on polyimide-loaded silicon with overlapped configuration reveals 0.2 dB/mm. Especially, alumina substrate imposes better attenuation than silicon.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.7
• /
• pp.704-709
• /
• 2007

In this paper, a CPW band-pass filter with a rejection band is proposed for UWB(Ultra-Wideband) communication systems. The proposed filter has a band-pass characteristic of wide-band by inserting only a slot in $50{\Omega}$ transmission line. To obtain the band-rejection function at WLAN frequency band($5.15{\sim}5.725GHz$), the designed filter is combined with folded slot resonators on the ground plane of the CPW structure. The fabricated CPW band-pass filter shows a compact size of $15.35{\times}13.60mm$, a wide passband of 2.8 GHz to 9.8 GHz and the narrow stop-band of 5.15 GHz to 5.71 GHz for 3-dB bandwidth. Also, the measured group delay is less than 400 psec throughout the operation frequency band except the rejection band.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.9
• /
• pp.11-18
• /
• 2002

This paper presents a CPW phase shifter and shunt stub with air-bridge on a 10-${\mu}m$-thick oxidized porous silicon(OPS) substrate using surface micromachining. The line dimensions of the CPW phase shifter was designed with S-W-Sg = 100-30-400 ${\mu}m$. And the width and length of the air-bridge with "ㄷ“ shape were 100 ${\mu}m$ and 400-460-400 ${\mu}m$, respectively. In order to achieve low attenuation, stepped air-bridge CPW phase shift was proposed. The insertion loss of the stepped air-bridge CPW phase shift is more improved than that of no stepped air-bridge CPW phase shift. The measured phase characteristic of the fabricated CPW phase shifter is close to 180$^{\circ}$ over a very broad frequency range of 28 GHz. The measured working frequency of short-end series stub is 28.7 GHz and the return loss is - 20 dB. And the measured working frequency of short-end shunt stub is 28.9 GHz and the return loss is - 23 dB at midband. As a result, the pattering of stub in the center conductor of CPW lines can offer size reduction and lead to high density chip layouts.