• 대한인간공학회지
• /
• 제19권3호
• /
• pp.39-49
• /
• 2000

During human-computer interaction(HCI), people typically send inputs to computers through electromechanical pointing devices. Many applied studies have therefore evaluated cursor-positioning movements made with various pointing devices. Though there were so many studies about performance of various pointing devices, it was nearly impossible to compare device performance each other until the Fitts' law was applied. It does appear that Fitts' law may predict performance reasonably well for the one C-D gain level. But in varying C-D gain levels, Fitts' law could not predict movement time. This study investigated the effects of C-D gain in mouse movement time and suggested a revised Fitts' model including C-D gain as an independent variable. The revised Fitts' model may use to measure the performance of various devices in varying C-D gain levels.

• 전기의세계
• /
• 제18권5호
• /
• pp.12-19
• /
• 1969

The sensitivity of transistorized d.c. amplifiers is mainly limited by drift at operating point caused by ambient temperature changes. A chopper-type transistorized amplifier is necessary to obtain a high sensitivity without recourse to drift compensation which requires the adjustment of several balancing controls. A chopper-stabilized system consisting of an electro-mechanical chopper for input and output and a high-gain a.c. amplifier is designed and analyzed. The gain of the a.c. amplifier, expressed as the ratio of voltages, is larger than 80db in the band of 50C/S - 100KC/S. The complete system gives an open-loop gain of 68db at direct current. The offset voltage is 20.mu.V referred in input and the voltage drift at the input is less than 10.mu.V/hr at 25.deg.C. This type of amplifier would be useful for the high-gain transistorized d.c. amplifier for analog computers. Also, due to the high input impedance, it is suitable for amplification of signals from wide range of source impedances.

• 한국광학회지
• /
• 제14권1호
• /
• pp.12-16
• /
• 2003

$0^{\circ}C$에서 5$0^{\circ}C$까지 온도를 변화시켜 가며 100 GHz의 채널 간격으로 L-band 40채널을 운용했을 때, 온도에 따른 L-band EDFA의 출력 스펙트럼 변화와 이득 변동폭을 측정하였다. 이득 포화 영역에서의 이득의 변화로 인한 출력 스펙트럼의 변화는 온도에 따른 출력 스펙트럼의 변화와 상반되는 점을 이용하여 1단과 2단 사이에 삽입한 가변 감쇄기를 조절하여 온도에 따른 이득 변동을 보상하였다. 그 결과, $0^{\circ}C$에서 최대 3 dB까지 차이를 보이던 이득 변동 폭은 가변 감쇄기를 이용한 온도 보상으로 1 dB 이내로 줄어듦을 볼 수 있었다.

• 전기학회논문지
• /
• 제63권2호
• /
• pp.257-260
• /
• 2014

In this paper, a high gain waveguide array antenna combining horn antenna on slot radiator was designed. And the fabricated antenna showed enough gain, improved efficiency and broadband characteristics for receiving satellite signals, compare to conventional microstrip antenna which has dielectric loss and radiation loss on transmission line. For easy fabrication, the waveguide structure was composed by 3-stages of radiator, signal coupler and transmission line. By experiment, the array waveguide antenna of 4 by 16 showed 28.3[dBi] gain and 2:1 of VSWR. And by combining horn antenna structure, the gain was increased 1[dB]. The received signal from Koreasat 6 by measurement showed 16[dBc] of C/N on BS(Broadcasting Satellite)-band and 14[dBc] of C/N on CS(Communication Satellite)-band.

• Journal of the Optical Society of Korea
• /
• 제18권6호
• /
• pp.657-662
• /
• 2014

We demonstrate a simulation of a parallel hybrid fiber amplifier in the C+L-band with a gain controlling technique. A variable optical coupler is used to control the input signal power for both EDFA and RFA branches. The gain spectra of the C+L-band are flattened by optimizing the coupling ratio of the input signal power. In order to enhance the pump conversion efficiency, the EDFA branch was pumped by the residual Raman pump power. A gain bandwidth of 60 nm from 1530 nm to 1590 nm is obtained with large input signal power less than -5 dBm. The gain variation is about 1.06 dB at a small input signal power of -30 dBm, and it is reduced to 0.77 dB at the large input signal power of -5 dBm. The experimental results show close agreement with the simulation results.

• ETRI Journal
• /
• 제42권6호
• /
• pp.943-950
• /
• 2020

We propose 8.2-GHz band radar RFICs for an 8 × 8 phased-array frequency-modulated continuous-wave receiver developed using 65-nm CMOS technology. This receiver panel is constructed using a multichip solution comprising fabricated 2 × 2 low-noise amplifier phase-shifter (LNA-PS) chips and a 4ch RX front-end chip. The LNA-PS chip has a novel phase-shifter circuit for low-voltage operation, novel active single-to-differential/differential-to-single circuits, and a current-mode combiner to utilize a small area. The LNA-PS chip shows a power gain range of 5 dB to 20 dB per channel with gain control and a single-channel NF of 6.4 dB at maximum gain. The measured result of the chip shows 6-bit phase states with a 0.35° RMS phase error. The input P1 dB of the chip is approximately -27.5 dBm at high gain and is enough to cover the highest input power from the TX-to-RX leakage in the radar system. The gain range of the 4ch RX front-end chip is 9 dB to 30 dB per channel. The LNA-PS chip consumes 82 mA, and the 4ch RX front-end chip consumes 97 mA from a 1.2 V supply voltage. The chip sizes of the 2 × 2 LNA-PS and the 4ch RX front end are 2.39 mm × 1.3 mm and 2.42 mm × 1.62 mm, respectively.

• Journal of the Optical Society of Korea
• /
• 제12권4호
• /
• pp.303-308
• /
• 2008

Directly modulated fiber-optic links generally suffer higher link loss and larger signal distortion than externally modulated links. These result from the electron-photon conversion loss and laser modulation dynamics. As a method to overcome the drawbacks, we have experimentally demonstrated the RF performance of directly modulated, ultra-strong injection-locked gain-lever distributed Bragg reflector (DBR) lasers. The free-running DBR lasers exhibit an improved amplitude modulation efficiency of 12.4 dB under gain-lever modulation at the expense of linearity. By combining gain-lever modulation with ultra-strong optical injection locking, we can gain the benefits of both improved modulation efficiency from the gain-lever effect, plus improved linearity from injection locking. Using an injection ratio of R=11 dB, a 23.4-dB improvement in amplitude response and an 18-dB improvement in spurious-free dynamic range have been achieved.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제16권5호
• /
• pp.675-681
• /
• 2016

A 41dB gain control range $6^{th}$-order band-pass receiver front-end (RFE) using CMOS switched frequency translated impedance (FTI) is presented in a 40 nm CMOS technology. The RFE consists of a frequency tunable RF band-pass filter (BPF), IQ gm cells, and IQ TIAs. The RF BPF has wide gain control range preserving constant filter Q and pass band flatness due to proposed pre-distortion scheme. Also, the RF filter using CMOS switches in FTI blocks shows low clock leakage to signal nodes, and results in low common mode noise and stable operation. The baseband IQ signals are generated by combining baseband Gm cells which receives 8-phase signal outputs down-converted at last stage of FTIs in the RF BPF. The measured results of the RFE show 36.4 dB gain and 6.3 dB NF at maximum gain mode. The pass-band IIP3 and out-band IIP3@20 MHz offset are -10 dBm and +12.6 dBm at maximum gain mode, and +14 dBm and +20.5 dBm at minimum gain mode, respectively. With a 1.2 V power supply, the current consumption of the overall RFE is 40 mA at 500 MHz carrier frequency.

• 한국정보통신학회논문지
• /
• 제20권7호
• /
• pp.1303-1310
• /
• 2016

본 논문에서는 전원전압 0.5V의 심전도 검사기(ECG)를 설계하고 칩으로 제작하여 성능을 확인하였다. ECG는 계측 증폭기, 6차 gm-C 저역 통과 필터 그리고 가변이득증폭기로 구성되어 있다. 계측증폭기는 이득이 34.8dB, 6차 gm-C 저역 통과 필터는 400Hz의 차단주파수를 가지게 설계되었다. 저역 통과 필터의 연산 트랜스컨덕턴스 증폭기는 저전압 동작을 위하여 차동 바디 입력 방법을 사용하였다. 가변이득증폭기의 이득 범위는 6.1~26.4dB로 설계되었다. 설계된 심전도 검사기는 TSMC $0.18{\mu}m$ CMOS 공정을 이용하여 $858{\mu}m{\times}580{\mu}m$의 칩크기로 제작되었다. 측정은 입력 신호를 포화시키지 않도록 외부 연결 저항을 조절하여 이득을 낮춘 상태에서 진행한바, 중간 주파수 이득 28.7dB, 대역폭은 0.5 - 630Hz을 얻었으며, 전원전압 0.5V에서 동작함을 확인하였다.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2000년도 추계 기술심포지움 논문집
• /
• pp.61-64
• /
• 2000

IMT 2000 단말기용 2.14 GHz 대역의 저잡음 증폭기 (Low Noise Amplifier, LNA)를 MCM-C 기술을 이용하여 제작하고 그 특성을 측정하였다. 먼저 저잡음 증폭기 회로를 설계한 후, 각 소자들의 고주파 library를 이용한 회로 시뮬레이션으로과 특성을 확인하였다. 시뮬레이션 상에서 이득(Gain)은 17 dB 였으며, 잡음지수 (Noise Figure)는 1.4 dB 였다. MCM-C 저잡음 증폭기는 LTCC 기판과 전극 및 저항체의 동시소성에 의해 코일(L), 콘덴서(C), 저항(R)을 기판 내부에 넣었으며, 마이크로 스트립 라인과 SMD 부품의 실장을 위한 Pad를 최상부에 제작하였다. 기판은 총 6 층으로 구성하였으며, 내부에 포함된 수동소자는 코일 2개, 콘덴서 2개, 저항 3개 등 총 7 개 였다. 시작품의 특성 측정 결과, 2.14 GHz에서 이득은 14.7 dB 였으며, 잡음지수는 1.5 dB 정도의 값을 가졌다.