• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.9
• /
• pp.685-697
• /
• 2017

In this paper, it is presented the result of design and fabrication for C-band solid state high power amplifier unit and components using in search radar. The solid state power amplifier(SSPA) assembly was fabricated using GaN(Gallium Nitride), which is semiconductor device, and the transmit signal output power of the solid state high power amplifier unit is generated by combining the transmit signal power of the solid state power amplifier configured in parallel through a design and fabricated waveguide type transmit signal combine assembler. Designed solid state high power amplifier unit demonstrated C-band 500 MHz bandwidth, maximum 10.5% duty cycle, transmit pulse width from $0.0{\mu}s{\sim}000{\mu}s$, and transmit signal power is 44.98 kW(76.53 dBm).

• ETRI Journal
• /
• v.36 no.3
• /
• pp.498-501
• /
• 2014

A C-band 50 W high-power microwave monolithic integrated circuit amplifier for use in a phased-array radar system was designed and fabricated using commercial $0.25{\mu}m$ AlGaN/GaN technology. This two-stage amplifier can achieve a saturated output power of 50 W with higher than 35% power-added efficiency and 22 dB small-signal gain over a frequency range of 5.5 GHz to 6.2 GHz. With a compact $14.82mm^2$ chip area, an output power density of $3.2W/mm^2$ is demonstrated.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 1996.06a
• /
• pp.27-31
• /
• 1996

In this paper, The SSPA(Solid State Power Amplifier) is 100 watts amplifier which is used with C-Band Satellite communication Up-Link frequency, 5.875 ∼6.425 GHz. SSPA requires more output power than is available from a single GaAs FET with result it is necessary to combine the output of many device. To achieve a high power, it is important to make a good N-way power divider which has a small different phase, good combining efficiency and high power handling capability. The reliability of Power GaAs FET decrease with increasing junction temperature, power amplifier in general dissipate amount of power. It is important to provide them with a heatsink and a temperature compensation circuit to dispose of the unwanted heat. To compensate temperature, Using PIN diode attenuator, it is enable to get a precision gain control. The output power of the SSPA is more than 100 watt with which the TWTA (Traveling-Wave Tube Amplifier) can be replaced. Each stage was measured by the Network analyzer PH8510C, Power meter Booton 42BD, The gain is more than 53 dB, flatness is less than 1.5 dB.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.3
• /
• pp.135-140
• /
• 2019

In this paper, a frequency split type broadband drive amplifier operating in the L, S and C bands was designed and fabricated. Transistor is difficult to efficiently use when the fractional bandwidth of the drive amplifier is more than 100%, In particular, the characteristics of the driving amplifier are important for operating the power amplifier in which the characteristics of the output power and the efficiency are sensitively changed according to the frequency band. A frequency split methods was applied to maximize the bandwidth of a drive amplifier and to divide the output of the drive amplifier into low band and high band so that the transistor of the power amplifier located at the rear of the drive amplifier can be efficiently used. The designed drive amplifier was fabricated in GaAs HBT technology and 9-layer SiP, and verified by the measurements. The fabricated drive amplifier shows a gain of more than 8 dB and an output power of more than 15 dBm in the operating frequency range.

• ETRI Journal
• /
• v.24 no.2
• /
• pp.81-96
• /
• 2002

This paper describes our design of a hybrid amplifier composed of a distributed Raman amplifier and erbium-doped fiber amplifiers for C- and L-bands. We characterize the distributed Raman amplifier by numerical simulation based on the experimentally measured Raman gain coefficient of an ordinary single mode fiber transmission line. In single channel amplification, the crosstalk caused by double Rayleigh scattering was independent of signal input power and simply given as a function of the Raman gain. The double Rayleigh scattering induced power penalty was less than 0.1 dB after 1000 km if the on-off Raman gain was below 21 dB. For multiple channel amplification, using commercially available pump laser diodes and fiber components, we determined and optimized the conditions of three-wavelength Raman pumping for an amplification bandwidth of 32 nm for C-band and 34 nm for L-band. After analyzing the conventional erbium-doped fiber amplifier analysis in C-band, we estimated the performance of the hybrid amplifier for long haul optical transmission. Compared with erbium-doped fiber amplifiers, the optical signal-to-noise ratio was calculated to be higher by more than 3 dB in the optical link using the designed hybrid amplifier.

• Journal of IKEEE
• /
• v.26 no.4
• /
• pp.722-727
• /
• 2022

In this paper, we present the design and characterization of a power amplifier (PA) monolithic microwave integrated circuit (MMIC) in the X-band. The device is designed using a 0.25 ㎛ gate length AlGaN/GaN high electron mobility transistor (HEMT) on SiC process. The developed X-band AlGaN/GaN power amplifier MMIC achieves small signal gain of over 21.6 dB and output power more than 46.11 dBm (40.83 W) in the entire band of 9 GHz to 10 GHz. Its power added efficiency (PAE) is 43.09% ~ 44.47% and the chip dimensions are 3.6 mm × 4.3 mm. The generated output power density is 2.69 W/mm². It seems that the developed AlGaN/GaN power amplifier MMIC could be applicable to various X-band radar systems operating X-band.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.5C
• /
• pp.522-529
• /
• 2002

MMIC circuits in whole receiver system was fabricated based on GaAs pHEMT technology. And a V-band downconverter module was fabricated by integrating these circuits. The downconverter module consists of a LO drive power amplifier which generates 24dBm output power, a low noise amplifier(LNA) which shows 20 dB small signal gain, an active parallel feedback oscillator which generates 1.6 dBm output power, and a cascode mixer which shows over 6dB conversion gain. The good conversion gain performance of our mixer made no need to attach any IF amplifier which grows conversion gain. Measured results of the complete downconverter show a conversion gain of over 20 dB between 57.5 GHz and 61.7GHz without IF amplifier.

• Journal of the Optical Society of Korea
• /
• v.18 no.6
• /
• pp.657-662
• /
• 2014

We demonstrate a simulation of a parallel hybrid fiber amplifier in the C+L-band with a gain controlling technique. A variable optical coupler is used to control the input signal power for both EDFA and RFA branches. The gain spectra of the C+L-band are flattened by optimizing the coupling ratio of the input signal power. In order to enhance the pump conversion efficiency, the EDFA branch was pumped by the residual Raman pump power. A gain bandwidth of 60 nm from 1530 nm to 1590 nm is obtained with large input signal power less than -5 dBm. The gain variation is about 1.06 dB at a small input signal power of -30 dBm, and it is reduced to 0.77 dB at the large input signal power of -5 dBm. The experimental results show close agreement with the simulation results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.11
• /
• pp.1081-1090
• /
• 2013

In this paper, a C-band 10 W power amplifier with internally matched input and output matching circuit is designed and fabricated. The used power transistor for the power amplifier is GaAs pHEMT bare-chip. The wire bonding analysis considering the size of the capacitor and the position of transistor pad improves the accurate design. The matching circuit design with the package effect using EM simulation is performed. To reduce the unsymmetry of IMD3 in 2-tone measurement due to the memory effect, the bias circuit minimizing the memory effect is proposed and employed. The measured $P_{1dB}$, power gain, and power added efficiency are 39.8~40.4 dBm, 9.7~10.4 dB, and 33.4~38.0 %, respectively. Adopting the proposed bias circuit, the difference between the upper and lower IMD3 is less than 0.76 dB.

• Electronics and Telecommunications Trends
• /
• v.37 no.5
• /
• pp.11-21
• /
• 2022

GaN (Gallium-Nitride) is a promising candidate material in various radio frequency applications due to its inherent properties including wide bandgap, high carrier concentration, and high electron mobility/saturation velocity. Notably, AlGaN/GaN heterostructure field effect transistor exhibits high operating voltage and high power-density/power at high frequency. In next-generation radar systems, GaN power transistors and monolithic microwave integrated circuits (MMICs) are significant components of transmitting and receiving modules. In this paper, we introduce technological trends for C-/X-/Ku-band GaN MMICs including power amplifiers, low noise amplifiers and switch MMICs, focusing on the status of GaN MMIC fabrication technology and GaN foundry service. Additionally, we review the research for the localization of C-/X-/Ku-band GaN MMICs using in-house GaN transistor and MMIC fabrication technology. We also discuss the results of C-/X-/Ku-band GaN MMICs developed at Defense Materials and Components Convergence Research Department in ETRI.