• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.619-621
• /
• 1996

This paper presents the study on the development of the power factor correction convener with ZVT Boost converter, which is better than the conventional PWM Boost converter to increase the switching frequency for high density and lower stress of switch. A simple DC and small signal model for the power factor correction converter with constant switching frequency is derived. The guide line for design of controller is summarized.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.124-130
• /
• 1997

The main switch of high-frequency boost converter may be failed because the high switching current or voltage can damage this switch. The high switching stress can be reduced by snubber circuit. In this paper, a new passive snubber circuit which can recover trapped snubber energy without added control is proposed for boost converter. The control of boost converter with proposed snubber is the same as the conventional one. In addition, the energy recovery circuit can be implemented with a few passive components. The analysis for proposed circuit is presented, and the validity of the circuit is verified through simulation and experiment.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.166-169
• /
• 2003

In this paper, a PWM Buck-Boost AC-AC converter for improvement of power quality of custom power is presented. The PWM Buck-Boost AC-AC converter is modelled by using circuit DQ transformation whereby the design guideline is obtained. Based on the analysis, the converter system is implemented with the design criteria and the experimental results show the validity of modelling and analysis.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.384-387
• /
• 2000

In this paper Power factor correction circuit of single-phase three-level boost converter is proposed. The advantage of the proposed control scheme for three-level boost converter are low blocking voltage of each power device low THD(Total Harmonic Distortion) and high power factor. The control scheme is based on the current comparator capacitor compensator and region detector, In simulations the proposed system is validated.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.348-350
• /
• 1994

In this paper, bi-directional buck-boost DC-DC converter for bus regulation system is presented. This converter which has one buck and one boost topology achieves bi-directional power flow using a common power inductor and alternative power switches. By connecting the battery to bus line, it can be regulated to bus voltage and charged the battery alternatively. And as an application, a mode controller is adopted to the converter.

• Proceedings of the KIEE Conference
• /
• 2009.04b
• /
• pp.168-170
• /
• 2009

This article analyzes a three phase interleaved boost converter for photovoltaic PCS, and compares with a single phase boost converter. The advantage of this approach, such as higher efficiency and reduced input and output ripple, are demonstrated by a three phase boost converter simulation.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.510-513
• /
• 2001

In this paper, an application of asymmetrical duty control method to a boost input type active clamp DC-DC converter is discussed. In order to verify the discussed results, a 50W prototype converter is built and is tested. Through the experimental results an asymmetrical controlled boost input type active clamp converter is validated.

• Proceedings of the KIPE Conference
• /
• 2002.11a
• /
• pp.129-132
• /
• 2002

In this paper, a PWM Buck-Boost AC-AC converter for improvement of power quality of custom power is presented. The PWM Buck-Boost AC-AC converter is modelled by using circuit DQ transformation whereby the both static and dynamic characteristics are analyzed completely. Finally, the converter system is implemented with the design criteria and the experimental results show the validity of modelling and analysis.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.355-357
• /
• 1996

With the wide-spread use of rectifier in electronic equipments, such problems as electronic components failures or equipment disorders have been occurred due to current harmonics. To overcome these problems, power factor correction circuits employing boost converter have been used. The switching stress of boost converter can be reduced by snubber circuit. Recently, research activities in snubber circuits have been directed to energy recovery snubber for improving the efficiency of power converter. In this study, a new passive snubber circuit which can recover trapped snubber energy without added control is proposed for boost converter The control of boost converter with proposed snubber is the same as the conventional one. In addition, the energy recovery circuit can be implemented with a few passive components. The circuit operation is confirmed through simulation.

• Proceedings of the KIPE Conference
• /
• 2009.11a
• /
• pp.155-157
• /
• 2009

This paper proposed a soft switching boost converter with an auxiliary circuit, and a modified control method for reduction of switch stress. The proposed converter applies an auxiliary circuit, which is added to the conventional boost converter and used to achieve soft switching for both a main switch and an auxiliary switch. The auxiliary circuit consist of a resonant inductor and two capacitors, an auxiliary switch. The main switch is operated ZVS turn-on, turn-off also auxiliary switch is operated ZCS turn-on, ZVS turn-off. The proposed soft switching boost converter has lower switch loss and higher efficiency than conventional soft switching boost converter.